Isolation Amplifiers
-
Product
Amplifiers
-
Amplifiers from Analog Devices deliver both high performance and high value. These amplifier ICs combine circuit design, manufacturing process innovation, and applications expertise to create products that simplify signal conditioning design.
-
Product
Logarithmic Video Amplifiers
DLVAs, ERDLVAs & SDLVAs
-
PMI’s Detector Logarithmic Video Amplifiers (DLVA, ERDLVA, SDLVA) are offered covering DC to 40 GHz with extended range models offering dynamic ranges over 70 dB. Our standard products provide exceptional temperature stability, log linearity and frequency response. As well, most SDLVAs provide a limited IF output. PMI offers custom DLVA’s and SDLVA’s to meet your requirements or replace obsolete products, please email your requirement to sales@pmi-rf.com so we can propose an instant solution.
-
Product
Single-Ended to Differential Amplifiers
-
Analog Devices has developed a broad portfolio of single-ended to differential amplifiers that help designers meet their high performance requirements. ADI single-ended to differential amplifiers enable the processing of both single-ended inputs to complementary differential outputs or differential inputs to differential outputs. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single-ended output.
-
Product
32-Ch Isolated Digital Input PCI Card
PCI-1733
-
ISA-Compatible with PCL-73332-ch Isolated digital inputHigh output driving capacityInterrupt handling capabilityD-type connector for isolated input channels
-
Product
RGB 1×3 Video Distribution Amplifier
VDA403
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.The second application is when the video signal is run over distances greater than 50 feet. The coaxial cable has a fair amount of signal loss over long distances. When multiple monitors are connected after long runs of coax, the degradation can be severe, especially when dealing with modern, high bandwidth signals that have 500+ lines of resolution.The VDA403 is a Video Distribution Amplifier designed for professional applications. It will operate with NTSC & PAL video signals as well as many common Black & White signals. These units use the latest integrated amplifier technology for superior performance and reliability. Custom units or modifications can be manufactured at a reasonable cost.
-
Product
Isolated Digital Input/Output Card
PCI-IDIO-16
-
The PCI-IDIO-16 is a low-cost, 6.8" card that provides isolated input and output for PCI-bus computers. The card has sixteen optically-isolated digital inputs for AC or DC control signals and sixteen isolated FET outputs. For safety reasons in working with AC voltages, insulating shields are provided with each card.
-
Product
High Isolation USB Switches
-
RF gain block amplifier from Pasternack is featured in our extensive in-stock RF amplifier selection. Our connectorized gain block RF amplifier uses SMA connectors. This SMA gain block amplifier has a minimum frequency of 500 MHz, a maximum frequency of 2 GHz and a typical gain of 17 dB.
-
Product
Composite 1×6 Video Distribution Amplifier
VDA106
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Amplitude Detectors with Isolators
-
Full band waveguide detectors are GaAs beam lead Schottky diode-based detectors that are specially designed for millimeterwave network analyzer applications. With a proprietary circuitry design and careful diode selection, these zero-biased detectors exhibit high sensitivity and extremely flat output characteristics. The below standard offering covers the frequency range of 18 to 170 GHz and offers a 1 MHz video bandwidth and 1 MΩ video output impedance. The standard models also have the capacity to handle a maximum RF input power of up to +17 dBm. The RF interface of these detectors is a standard waveguide with an integrated Faraday isolator to improve the port VSWR. The output voltage polarity is negative and the connector type is a female SMA. Other configurations are offered as custom models.
-
Product
Analog Summing Amplifier
SIM980
-
Stanford Research Systems, Inc.
The SIM980 Summing Amplifier has four input channels that can be added or subtracted from each other. The output noise is less than 60 nV/√Hz, and crosstalk between channels is less than -80 dB. With a bandwidth of 1 MHz, a slew rate of 40 V/ms, and input offsets that are trimmed to ±100 µV, the SIM980 is extremely useful in many analog applications.
-
Product
RF & Microwave Broadband Amplifiers
-
SHF Communication Technologies AG
SHF has been active in the design and production of broadband RF-microwave amplifier. The outstanding performance makes our amplifiers suitable for a wide variety of applications in R&D. This includes not only optical communications, but also satellite communications, high-speed pulse experiments, data transmission, quantum communication, radar and antenna measurements.
-
Product
16-Ch Isolated Digital Input Modules
ADAM-5051S
-
50 Vmax Input Voltage2500 Vdc Optical Isolation70 Vdc Over Voltage Protection16-channel
-
Product
8-Channel Amplifier and Low-Pass Filter Module
SCS-816
-
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
Product
10-Ch. 0… 5V 400mA Isolated
YAVAP955
Programmable Voltage Source
The YAV board AP955 contents 10 CAN Bus programmable bipolar Isolated precision and low noise 0 to 5VDC voltage sources up to 400mA output, with Tripaddle VPC connector.
-
Product
12-bit, 100KHz, 16SE/8DIFF Isolated Analog Input Board
APCI-3001-16
-
16 single-ended or 8 differential inputs 12-bit resolution Optical isolation 500 V 100 kHz data transfer rate Automatic analog acquisition 8 digital I/O, 24 V, isolated, timer Trigger functions Graphical display of the measured data
-
Product
Amplifier Systems
-
Sutter Instrument provides a complete line of electrophysiology recording hardware and software, ideal for applications ranging from tissue slice patch clamp over dissociated cell recordings to cell line studies.
-
Product
16-CH Latching Relay Outputs & 16-CH Isolated DI Card
PCIe-7256
Analog Output Module
ADLINK's PCIe-7256 features all Form C type relays, ideal for device connection with on/off control. With latching relays, the PCIe-7256 further provides operating power conservation, while the status of each latching relay output is indicated by onboard LED. When the relay is in SET, its corresponding LED lights. Latching relays also feature unchanged status even when the system powered off, making the PCIe-7256 suitable for critical applications requiring output status to be maintained even under fault conditions. All digital input channels are non-polar and optically isolated, and may be set for optional use of RC filter. The PCIe-7256 also features a change-of-state (COS) function generating interrupt when any digital input changes state.
-
Product
Isolated PWM Controllers
-
Renesas' communications product portfolio includes a synchronizing pulse width modulating (PWM) current mode controller for subscriber line interface circuits (SLICs).
-
Product
Portable Power Amplifier
PAV250Bip
-
PAV250Bip is the portable OPAL-RT used amplifier model, which is specially designed for R&D of power system simulation. It is designed with linear type amplifier so that it is with precise accuracy, which could be adapted to various capacitive and inductive load.
-
Product
Solid State Power Amplifiers (SSPAs)
-
CHANGSHA KAIYUAN INSTRUMENTS CO., LTD.
* Ruggedized for use in pulsed airborne, naval and ground radar* Found in weather forecasting Doppler radar systems* Utilized world-wide in air traffic control and precision approach radar systems
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, 1 kV Isolation
41-752A-103
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI Isolated Single Channel Voltage/Current Source, 100V
M9186A
Source Measure Unit
The V/I source lets you source a voltage and measure the resultant current, or source a current and measure the resultant voltage. It consist of two separate amplifiers, denoted "low" and "high" that share a common output connection. The "low" amplifier provides voltages in the range of 16 volts at up to 200ma and the "high" amplifier provides voltages in the range of 100V at up to 20mA.
-
Product
Limiting Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink's limiting amplifiers use FET device with good consistency and distributed traveling wave amplifying circuit to design. Good amplitude and phase consistency characteristics can be achieved in a wide input dynamic range. It's the key component of the electronic system. Keylink's limiting amplifiers can be categorized as follows.
-
Product
Low Noise Amplifiers for Radio Amateurs
-
Our Low Noise Preamplifiers are remarkable for extremely low noise, excellent SWR, high efficiency and a high IP3. The Low Noise amplifiers are especially selective and absolute stable therefore oscillation is avoided. Even if you have a bad SWR. This is the reason why radio amateurs and club-stations all around the world trust in Kuhne electronic equipment. The products are perfect for use in contests, EME, MeteorScatter, Aurora and Tropo DX. Small mechanical measurements and technical innovations from the professional sector, e. g. milled aluminium cases, enable high temperature stability and tower mounting. Numerous contest victories, records and first contacts with a country were and are achieved with Kuhne products. Don't compromise and get technology from Kuhne electronic!
-
Product
16-Ch Isolated Digital I/O Module With LED
ADAM-5055S
Digital I/O Module
I/O Type: 8 DO & 8 DIOptical Isolation: 2500 VdcPower Consumption: 0.68 W (Typical)16-channel
-
Product
PXI 5A Power Multiplexer, 8-Bank, 5-Channel, Isolated Common
40-651A-014
Multiplexer Module
The 40-651A-014 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats.
-
Product
Amplifiers
-
Holzworth Instrumentation, Inc.
Holzworth amplifier products are designed for use in applications where low phase noise is critical. An added benefit of the low phase noise characteristic is extremely low additive jitter, making Holzworth amplifiers beneficial for some communications systems.
-
Product
1U, Rack Mount, Pulse Distribution amplifier
A5000P
-
The Quartzlock A5000P is a 1U, rack mount, pulse distribution amplifier
-
-
Product
High Voltage Linear Amplifier
A800X
-
This unit is a version of A800 amplifier equipped with two inputs, DC-offset and output atenuation. Input A is a normal non-inverting one. Using this input alone makes A800X functionally identical with A800 amplifier.Input B can act as a inverting or non-inverting depending on the position of the corresponding switch.
