Simulators
create what could be.
See Also: Simulation, Simulation Software, Simulation Testing, Emulators
-
Product
PCI High Density Resistor Card 5-Channel, 12-Bit, 0 To 4k Ohm
50-295A-021-5/12
Programmable Resistor Modules
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
AFDX ® / ARINC 664 Test Cards
-
Our AFDX ® / ARINC664 test cards can be used for test and simulation applications in which it is necessary to send and receive data via the AFDX® data bus. They support the 10/100 Mbit / s ARINC 664 Part 7 Ethernet interface as well as the next generation 1 Gbit / s Ethernet. / ARINC 664 test cards are delivered with device drivers, high-level interfaces (APIs) for Windows Linux, VXWorks and LabVIEW / LabVIEW Real-Time (further on request).
-
Product
PXI Millivolt Thermocouple Simulator Module - 8 Channel
41-760-004
Simulator
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 26 or 8 channels—each channel providing a low-voltage output across two connector pins capable of providing ±20mV with 0.7µV resolution, ±50mV with 1.7µV resolution and ±100mV with 3.3µV resolution, covering most thermocouple types.
-
Product
Bidirectional DC Power Supply
62000D
DC Power Supply
Chroma 62000D programmable bidirectional DC power supplies provide both power source and load characteristics. These two quadrant power supplies allow power from the DUT to be converted back to the utility grid and so are ideal for testing renewable energy power systems such as PV, storage, and EV inverters as well as a wide range of bidirectional power conditioning system (PCS) and may also be used as a battery simulator.
-
-
Product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD | VP 230036
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.
-
Product
PCI High Density Pecision Resistor Card, 6-Channel, 3.5Ω To 395kΩ
50-298-042
Programmable Resistor Modules
The 50-298-042 is a high density programmable resistor card with 6 channels which can be set between 3.5Ω and 395kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Precision Resistor Card 9-Channel, 2Ω To 52.4kΩ
50-297-033
Programmable Resistor Modules
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Electrostatic Discharge Simulator
ESD61000-2
-
ESD simulator (Electrostatic Discharge Generator or Electrostatic Gun) is in full compliance with IEC 61000-4-2, EN61000-4-2, ISO10605, GB/T17626.2, GB/T17215.301 and GB/T17215.322. The ESD generator is designed for the assessment of electrical and electronic equipment to withstand ESD performance. ESD61000-2/ESD61000-2A has LCD display in both English and Chinese, they equipped with an infrared remote control which can allow you do the test in some special place.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 472Ω
50-298-120
Programmable Resistor Modules
The 50-298-120 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 472Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Dual Bus 64-Channel 2A PCI Fault Insertion Switch
50-190-102
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
Optical Design and Simulation Services
-
The key area of expertise and the basis for all developments at the Fraunhofer IOF is optical and mechanical design as well as the simulation and analysis of optical and opto-mechanical systems inclusive of thermal and thermo-optical effects. Extensive design and modeling tools enable the simulation and optimization of systems for the THz to X-ray range - from micro-optics to astronomical telescopes.
-
Product
Thermometer / Cardiac / Invasiv, non Invasiv Blood Pressure Simulator
TBH-400
-
Test device for functional testing of medical thermometers (DIN EN ISO 80601-2-56), cardiac output, invasive (IEC 60601-2-34) and non-invasive blood pressure devices (IEC 60601-2-30).
-
Product
Fault Simulation
Concurrent Fault Simulator
-
TurboFault combines high performance, versatility and accuracy. It is highly competitive with hardware accelerators for classical test fault grading. It supports synchronous and asynchronous designs at the gate level, including tri-state gates, latches, flip-flops, single and multi-port RAMs, complex bus resolution functions, and User Defined Primitives (UDPs).
-
Product
PCI High Density Pecision Resistor Card
50-298-024
Programmable Resistor Modules
The 50-298-024 is a high density programmable resistor card with 9 channels which can be set between 2.5Ω and 6.97kΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PCB S.I/P.I (Signal Integrity/ Power Integrity)
-
Why need for PCB Simulators?Higher data speed (>GHz) Higher density Larger system size EMI concern Cost cut down Reduce of project term
-
Product
Analyze RTL
-
ASICs and FPGA routinely have millions of gates with memories, transceivers, third party IP and processor cores. Problems can be time consuming and complex to debug in the lab and through simulations. Designers need verification tools that can identify problems quickly to reduce their verification and debug time before simulation, before synthesis, and definitely before burning chips in the lab.
-
Product
Intelligent Interface Card
IIB-1553-VXI-4C
-
The IIB-1553-VXI-4C is an intelligent interface card which provides 4 independent channels for full MIL-STD-1553 test, simulation and bus analysis functions on the VXI bus. All 1553A, 1553B, McAir and STANAG 3838 variants are supported. Each independent channel may be operated as a concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with a windowed Bus Monitor (BM), or as a stand-alone Chronological Bus Monitor (CBM) with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. Each channel provides a variable amplitude dual redundant 1553 interface, with 2 Mbytes of dual ported RAM. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
Product
Communication Data Logger
LE-270AR
-
LE-270AR is an Analyzer and Communication Data Logger of CAN/LIN. It has logger mode with which you can records CAN/LIN communication logs in the SD/SDHC card for long hours and remote mode with which you can monitor data at real time by connecting the analyzer with PC. It also has simulation mode with which you can repeatedly transmit CAN/LIN data which is registered in advance and selected on the PC. You can measure 2 channels of CAN/LIN communication lines and can simultaneously register voltage data of 4 external signals.Its power failure protection, waterproof, and low power consumption widens the usage of analyzer such as in the automation factories and other production factories.
-
Product
USB 2.0 SmartCable™ For ARINC429Test And Simulation
ASC429-x
-
USB 2.0 SmartCable™ for ARINC429 Test and Simulation with 6 channels (2Tx/4Rx) and 12 channels (4Tx/8Rx).
-
Product
Engine Speed Control and Measurement (Test Set A)
MS 1100
-
*Checks the parameters such as current, voltage, speed, and turbine gas temperature of 804E and 811 engines Portable instrument*Testing of Automatic engine control system and after burner control system*Simulates the temperature signal derived from the engine TGT (Temperature Gas Turbine) thermocouples*Simulates the speed signal, NL (low pressure shaft speed signal) drive from the L.P shaft Probe*Indicates the current signal to the FCU solenoid derived from the engine control amplifier*Measure the TGT and NL simulated signal at static position*Measure the signal produced by the engine TGT thermocouples*Measure the NL signal produced by the LP shaft*Measure the NH (High-pressure shaft speed) signal produced by HP shaft*Indicates the solenoid current, produced by the engine control amplifier*Indicates the solenoid voltage, produced by the engine control amplifier*Used to test engine in both static and dynamic states
-
Product
FPGA Simulation
Active-HDL
-
Active-HDL™ is a Windows® based, integrated FPGA Design Creation and Simulation solution for team-based environments. Active-HDL’s Integrated Design Environment (IDE) includes a full HDL and graphical design tool suite and RTL/gate-level mixed-language simulator for rapid deployment and verification of FPGA designs.
-
Product
Clamping Force Tester
KRD102
-
KRD102 series clamping force tester is an indispensable test method for improving products into high-quality fields. It is suitable for research, development, quality control and manufacturing of electronics, electromechanical, optoelectronic, automotive, toy, packaging and other industries. It can simulate the situation that the goods in the container are clamped when they are transported from the container to the warehouse. Whether the goods are damaged due to the clamping, so as to evaluate the anti- clamping ability of the packaging.
-
Product
Electronics
-
Electromagnetic, Signal Integrity, Thermal and Electro-Mechanical Simulation Solutions. The use of Ansys Electronics solution suite minimizes the testing costs, ensures regulatory compliance, improves reliability and drastically reduces your product development time. All this while helping you build the best-in-class and cutting-edge products. Leverage the simulation capability from Ansys to solve the most critical aspects of your designs
-
Product
Educational Patient Simulator
EasySim®
-
The new and improved EasySim® arrhythmia simulator fits in the palm of your hand! The ultra-portable (6.6″ x 2.4″ x .5″), ultra-lightweight (10 oz.) remote control will place you on the leading edge of medical education technology. The highly intuitive design features 48 direct-access keys in a remarkably easy to use format. No codes to memorize! No fuss to set up!
-
Product
Interface
RP-708
Interface
The RP-708 is a two-channel ARINC 708 weather radar display data bus PMC module interface, supporting variable frame sizes for embedded applications, simulation and test. Abaco Systems provides integrated support for this module on PCI, PCIe, CompactPCI, VME, VXI and native PMC platforms. Each RP-708 channel can be configured as two transmit channels, two receive channels, or one transmit channel and one receive channel simultaneously.
-
Product
IPX7 Water Ingress Protection Immersion Test Chamber
CX-IPX7
-
Shenzhen Chuangxin Instruments Co., Ltd.
IPX7 Water Ingress Protection Immersion Test ChamberThe main function of the immersion test equipment is for the electronic and electrical products, lamps, electrical cabinets, electrical components, automobiles, motorcycles and their parts and other products in the simulated rain conditions, the physical and other related properties of the test.
-
Product
Electronic Loads/Sinks
-
An electronic load offers the possibility of testing the specimen under different loads. Various load changes are simulated, as they can occur in normal operation. For this purpose, the relevant load current is set in a defined range and electronically controlled. For the test, different operating states are either programmed or entered into the system via an interface (USB, RS-232, GPIB...). For easy handling and quick use, there are four operating modes.
-
Product
PXI/PXIe Fault Insertion Switch, 32-Chan 2A, N/C Through Relays, Fault Buses on M & U
40-190C-212
Fault Insertion Unit
The 40-190C-212 (PXI) and 42-190C-212 (PXIe) are fault insertion switches with 32 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Aircraft Simulator
ePlane PC
-
Pneumatic connections Ps, Pt and AoA (option)High accuracy, high resolutionSelectable pressure units: hPa; mb; in Hg; mmHg; ft; m; kts; km/h, ft/min; and Mach number and needle equipment visualisationSoftware executable under Windows 2000 and XPUSB cable for PC connection
