Simulators
create what could be.
See Also: Simulation, Simulation Software, Simulation Testing, Emulators
-
Product
Electronics Cooling Simulation Software
FloTHERM
-
Perform thermal analysis, create virtual models, and test design modifications of electronic equipment before physical prototyping. FloTHERM uses advanced CFD techniques to predict airflow, temperature, and heat transfer in components, boards, and complete systems, including racks and data centers. It''s also the industry''s best solution for integration with MCAD and EDA software.
-
Product
PCI High Density Potentiometer Card 5-Channel, 8-Bit, 0 To 255 Ohm
50-296A-021-5/8
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI 1A Fault Insertion Switch 11-Channel
40-195-101
Relay
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
-
Product
Distributed Test Manager
DTM
-
The Distributed Test Manager (DTM) is a Windows™ application which enables many different types of system level testing by simulating multiple devices in a system. DTM is a system level simulator that is unique compared to other Triangle MicroWorks tools which test the communications of a single device. DTM is a highly extensible tool with multiple options for configuring devices, creating test cases, and simulating data in the system.
-
Product
Vibration Testing System
-
Torontech is now offering Vibration Test Systems, Shock Test Systems, Bump Test Systems, Drop Tester, and Packaging Transportation Simulators.
-
Product
Towing Dynamometer
RS-200K
-
RS-200K towing dynamometer is designed for testing Class A trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-200K is built with a heavy-duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-200K is designed to maintain 200,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are nolead-acid batteries to charge and testing is unlimited at low speeds.
-
Product
PXI RTD Simulator Module, 4 Channel, PT1000
40-263-503
Simulator
The 40-263-503 is a 4-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Physiology / Altitude Testing Rooms
-
Darwin Chambers Company has teamed up with Colorado Altitude Training (CAT), located in Boulder, Colorado, to offer a unique chamber for altitude simulation. CAT advances altitude simulation technology by maintaining the largest research and development division in the industry. CAT has invested heavily in technology and research to maximize comfort.A CAT system can reduce the oxygen content from 20.9% to 15.2% to simulate 9,000 feet at sea level, while keeping the pressure unchanged. Whether at real altitude, in a hypobaric chamber, or in an environmental room/CAT system, the amount of inspired oxygen and physiological effects are the same.
-
Product
MIL-STD-1760
M4K1553Px(S)-1760
-
The M4K1553Px(S)-1760 interface module for the multimode, multiprotocol, Excalibur 4000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M4K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M4K1553Px-1760 modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.
-
Product
V2X Test Tools
-
Validate and verify your V2X application with our Mx-Drive Mobility Simulator. Use the Mx-DSRC Compliance tester for USDOT certification.
-
Product
MCDU Simulator
-
Square Peg Communications Inc.
The Multi-Function Control and Display Unit (MCDU) is an input device for the flight management system and other computer systems of modern aircraft. It consists of a screen and an alphanumeric keyboard and can be found within reach of the pilot in the cockpit of the aircraft. The operation of the MCDU is described in the ARINC 739 specification.
-
Product
Temperature Simulators
-
A single select button scrolls quickly between the 3 factory set calibration points for efficiency. Two models to choose from: 271-018 (0°F, 32°F, 212°F) and 271-019 (32°F, 212°F, 500°F). Each unit includes a 3-point UKAS Accredited Calibration Certificate so you know that you''re using a precision instrument. Also included is a 3 foot type K test lead for connecting up your type K meters. You get precision at an economic price. Simple and fast!
-
Product
PCI Precision Resistor Card 4-Channel, 2Ω To 26.7kΩ
50-297-132
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCIe-7858, Kintex-7 325T FPGA, 1 MS/s, DRAM Multifunction Reconfigurable I/O Device
786457-01
Multifunction Reconfigurable I/O
PCIe, Kintex-7 325T FPGA, 1 MS/s, DRAM Multifunction Reconfigurable I/O Device - The PCIe‑7858 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7858 features a dedicated analog-to-digital converter per channel for independent timing and triggering. This device offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
Product
PXI RTD Simulator Module 18 Channel PT100
40-262-001
Simulator
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the design principles of our 40-260 PXI Precision Resistor, this RTD simulator module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels.
-
Product
PXI 16 Channel Switch Simulation Module
40-480-121
Switch Simulation Module
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
Product
Flight Processor Emulator
-
Flight Processor Emulators are an essential part of satellite simulators – both for testing of flight software and at the heart of operational simulators. The Terma Emulator is a suite of instruction-level emulators, based in the ESOC Emulator Suite, supporting several processors used in the Space industry: MIL-STD-1750 in both A and B variants. ERC32 in both 3-chips configuration (691-E) and single chip configuration (695-F). LEON 2 (AT-697)...
-
Product
PXI Arbitrary Waveform Generators
-
Keysight's PXI arbitrary waveform generator (AWG) deliver unprecedented performance for creation of complex wideband waveforms. High sampling rate and high bit resolution provided in a single instrument enable designers to create ideal waveforms for accurate test of radar, satellite and frequency agile systems. Providing up to 500 MHz of modulation bandwidths and over 65 dBc of spurious free dynamic range, PXI arbitrary waveform generators can be combined with a wideband I/Q upconverter to achieve modulation bandwidth of 1 GHz at microwave frequencies for realistic signal simulations for IF and RF subsystem test.
-
Product
Systems Integration (SIL) Lab Data Acquisition
System
Bloomy’s SIL data system allows testing and simulation of every system component on the aircraft. The functionality of these complex integrated systems are fully tested, debugged, and verified safely in the lab prior to flight testing. This reduces cost and schedule for new aircraft. Bloomy has applied its expertise to multiple SILs.
-
Product
PXI-6733, 16-Bit, 8-Channel, 1 MS/s PXI Analog Output Module
778512-01
Analog Output Module
16-Bit, 8-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6733 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response tests (including acoustic distortion testing) and simulation (such as three-phase power simulation). In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6733 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
Voltage Sag Generator
SKS-1120GTA
-
Shanghai Sanki Electronic Industries Co., Ltd.
The cycle drop simulator is used to reproduce the voltage fluctuation phenomenon of commercial power supplies. Simulate the grid voltage drop and short-term interruption caused by the accident or the sudden change of the large load in the low-voltage power grid, or the grid voltage change caused by the continuous change of the load. Used to evaluate the performance of the equipment under these voltage changes.
-
Product
Configurable Simulation Of ECU Diagnostics.
TestCUBE2
-
Softing Automotive Electronics GmbH
The ECU simulation TestCUBE2 is the counterpart for all cases of application in which an ECU is not yet (e.g. preparation of workshop tests) or no longer (e.g. tester regression test) available. TestCUBE2 is a configurable hardware and software solution for simulating ECU diagnostics with real bus communication. With just one device, you can simulate several ECUs or even an entire vehicle at the same time.
-
Product
Acceleration Simulation Mode (ASM) Roller Set
ASM-P-PLUS | VP 230047
-
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-P-PLUS roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The increased tractive force of its eddy current brake means that the ASM-P-PLUS is also suitable for power measurements at constant speed and constant tractive force.
-
Product
Signal Integrity Studio, Analysis & Simulation SW for WAVEPULSER High-Speed Interconnect Analyzer
WavePulser-Signal Integrity (SI) Studio
Analyzer
WavePulser Signal Integrity (SI) Studio is included as a single license in the WavePulser 40iX-BUNDLE or can be purchased as an additional license for offline access to additional users. WavePulser Signal Integrity (SI) Studio combines S-parameter, Impedance profiling and de-embedding measurements, channel and equalizer modeling, eye diagrams and jitter analysis in a single affordable software package for emulating the complete serial data channel.
-
Product
PathWave RF Sythesis (Genysys)
-
Analyze RF and microwave circuits and systems with fast simulation and powerful optimization tools. Explore performance trade-offs with automatic circuit synthesis technology. PathWave RF Synthesis (Genesys) provides entry-level functionality suitable for all RF and microwave circuit board and subsystem designers.
-
Product
50 Pin D-type Connectors & Cables
-
These standard voltage and high voltage 50 Pin D-type connectors are used for both PXI & LXI switching and simulation products for medium density applications.
-
Product
Distributed Simulation & Test Environment
-
Modular hardware and software architecture with multipurpose modules and components in a common and reconfigurable simulation and test environment easily adaptable to meet project‐ and customer‐specific requirements.
-
Product
GPS Simulator
ADIVIC MP6220
Simulator
Multi-channel GPS simulator for GPS receiver position fix testIndividual channel is power adjustableSingle channel mode for receiver S/N ratio testTunable power output level from -160dBm to -55dBm
-
Product
Environmental Simulation
-
During the development phase of new products, we analyze the weak points in simulation tests and test the products for environmental influences. The relevant standards are used as the basis for the simulation tests.
-
Product
Waterproof Test Chamber
JL-XC
-
JL-XC series waterproof test chamber is mainly used for small electronic and electrical products. Such as lamps, electrical cabinets, electrical components and so one. The products are tested for physical and other related properties under simulated climatic conditions. After the test, it is judged whether the performance of the product meets the requirements by verification, so as to be used in the design, improvement, verification and factory inspection of the product. Comply with IEC60529:2001 《Degrees of protection provided by enclosures (IP Code)》, GB4208-2008 《Shell Protection Grade (IP Code)》 14.2.8 Terms and GB7000.1 《Lamps Part 1: General Requirements and Tests》 9.2.9 Terms.
