-
Product
Emulators
-
High fidelity DC power system and motor drive inverter testing is made achievable with the use of advanced power emulation.
-
Product
High-Performance JTAG Emulators
XDS560 Series
-
Blackhawk XDS560-class models are offered with PCI, USB, and Ethernet host interfaces. These XDS560 models support the first generation of TI XDS560-class high-speed JTAG connection between Code Composer Studio and the target device.
-
Product
Network Emulators
-
Rohde & Schwarz offers class-leading signaling testers. We established our position as leading supplier of LTE communications testers with the popular, all-in-one R&S®CMW500 platform. Now we are building on the expertise that enabled its success with the high-performance R&S®CMX500 radio communication tester.Secure the industry-leading wireless network emulators for your 5G NR and legacy technology challenges – from R&D design stages up to end-to-end application testing, production and conformance tests.
-
-
-
Product
System Trace Emulators
XDS560v2
-
The XDS560v2 System Trace Emulator is the second generation of the XDS560-class emulator design from Texas Instruments. It provides cost effective real-time emulation, debugging, and high-performance System Trace (STM) for Texas Instruments devices over both USB and Ethernet PC interfaces.
-
Product
Wireless Network Emulators
-
Keysight’s industry-leading range of wireless network emulators and device test solutions enable the entire mobile device ecosystem to accelerate the market introduction of new wireless devices by streamlining the workflow from early prototyping, development, and design verification to conformance, carrier acceptance, and high-volume manufacturing.
-
-
Product
Chromatic Dispersion Emulator
CS-CDE
-
The ClearSpectrum™-CDE is a chromatic dispersion emulator suited for test and measurement. This 1U half 19-inch rack-mountable module is designed to emulate tens of thousands of picoseconds per nanometer in a compact unit while maintaining very low insertion loss. It is a passive, ready-to-use emulator which can be cascaded several times to achieve higher levels of dispersion.
-
Product
Accessories: Intermittent Fault Emulator
-
The Intermittent Fault Emulator (IFE) is the solution. The IFE enables manufacturers, suppliers and operators of any Intermittent Fault Detection (IFD) tester to demonstrate and verify its capabilities to detect and isolate intermittent faults.
-
Product
Sensor Signal Emulator
-
This Sensor Signal Emulator is specially designed for Automotive Technicians to troubleshoot electrical control systems problems in the car. It simulates the signals generated from different sensors in the vehicle and the ECU which enables technicians to pinpoint the actual faults in the electrical control system in cases of doubt over their judgment of replacing the sensors or the entirety of the connecting wires to the ECU.
-
Product
Dual Mobile Comm DC Source w/ Battery Emulation
66319B
DC Power Supply
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections. The Keysight 66319B dual output mobile communications dc source provides two outputs for testing both the main battery power and the battery charger circuitry, allowing customers to test phones and chargers with the same equipment. This feature helps save on rack space (2 outputs in a rack box) and eliminates the need for two separate power supplies.
-
Product
Channel Emulator
-
Qosmotec Software Solutions GmbH
Knowledge about channel models is not necessary to run tests with the QPER Channel Emulator. It applies the visualised virtual drive test concept, which is also used in the handover tester, to a fully fledged channel emulator: The tester outlines the network layout on the screen and defines a drive test route on the map. While running a simulated drive test, all channel effects are automatically calculated by QPER and applied to the channel emulation hardware.
-
Product
V5.1/V5.2 Local Exchange Emulator
Emutel Virtuoso
-
Emutel Virtuoso supports both V5.1 and V5.2 protocols including PSTN, BCC, LINK, PROTECTION GROUP 1 and PROTECTION GROUP 2. Up to 8 E1 connections are available for V5.1 / V5.2 and multiple V5.1 and V5.2 can be established simultaneously.
-
Product
PCIe Basic Protocol Multi Terminal Emulation
Sy629PCIe-BPT
-
The Sy629PCIe-BPT card provides a convenient means for transmitting and receiving data over an ARINC 629 bus in accordance with the transmit and receive programme defined by data written into the XPP and RPP memory. In particular, this product can emulate up to 120 terminals transmitting on an ARINC-629 data bus whilst correctly maintaining the approved Basic Protocol.
-
Product
HEV / EV / Grid Emulators and Test Systems
-
With Scienlab test systems and test software, Keysight offers customized test environments for the development and testing of electronic components according to hybrid and electric vehicle testing standards. Our solutions help you to accelerate your e-mobility applications from the battery, Battery Management System (BMS), inverter, the charging interfaces of Electric Vehicle (EV), and Electric Vehicle Supply Equipment (EVSE).
-
Product
Emulates AT8xC5122 Derivatives with 6/12 Clocks/Cycle
FE-5122
-
* Emulates AT8xC5122 Derivatives with 6/12 Clocks/Cycle * 32K Code Memory * Software Trace * Real-Time Emulation * Frequency up to 40MHz * MS-Windows Debugger for C and Assembler * Keil Vision2 Debugger Compatible * PLCC-68, PLCC-28, LQFP-32 and VQFP-64 Emulation Headers * Serially Linked to PC at 115Kbaud
-
Product
Mobile Network Emulator
-
Qosmotec Software Solutions GmbH
QPER Mobile Network Emulator enables engineers to simulate handover scenarios in mobile networks without a fully-fledged test lab. Based on Qosmotec’s QPER technology, it allows to test UE and SIM-Card behaviour in a completely emulated mobile network: Cells can be configured with all relevant cell parameters (MCC, MNC, LAC, CI, etc.), SIMs can be added to the HLR, and UEs can use standard circuit switched and packed switched services. Thus, the QPER Mobile Network Emulator emulates the all components of a mobile network – consisting of core and radio functionality – and creates RF signals. It supports GSM, GPRS and EDGE (900 MHz, 1800 MHz) as well as UMTS (2100 MHz).
-
Product
PCIe Exerciser & PCIe LTSSM Exerciser with L1 Substate Analysis
U4305B
Protocol Exerciser
Supports 2.5 GT/s (Gen1), 5.0 GT/s (Gen2) and 8.0 GT/s (Gen3) speeds Link width support x1 through x16 lanes Standard PCIe half-size card form factor to fit into most platforms Emulate Root Complex (RC) or Add-In-Card (AIC)
-
Product
Development System
FE-51MX
-
* Emulates Philips P8xC51MA/B/C , P89C669 Microcontrollers * 1MByte Code Memory * Based on bond-out Technology * Frequency up to 24MHz 3V / 5V Operation * Huge Real Time Trace Memory * Windows Debugger for C/C++ and Assembler * Target Board Included * RS-232 or USB Interface * 64K C/ASM and 8K C++ Included
-
Product
Development System
FE-SND2
-
* Emulates Atmel AT89C51SND2 Microcontrollers * 62K Code Memory * Real-Time Emulation * Frequency up to fmax * ISP and X2 Mode Support * Windows Debugger For C, C++ and Assembler * USB or RS-232 Linked to PC * C Compiler and Assembler
-
Product
PathWave BenchVue Advanced Battery Test And Emulation
BV9210B
-
The BenchVue Advanced Battery Emulation Software helps determine your device's power consumption, emulate battery, and import existing battery models.
-
Product
Emulators
-
Comware Technical Services, Inc.
Comware’s emulators replace your legacy system with modern hardware without changing the operating system and the application software.
-
Product
Network Emulator
Netropy® 100G
-
Developed for the pre-deployment testing and validation of high-speed 100GbE networks, the 100G is capable of precisely emulating 25, 40, 50 and 100Gbps WAN links. It allows service providers and storage system manufacturers to validate how WAN impairments--such as latency, packet loss or congestion--will affect performance over all data center links prior to going to market. Available 1/18
-
Product
Virtual Network Emulator
NetropyVE™
-
NetropyVE™ is the virtual edition of the Netropy network emulator. It offers advanced capabilities to benchmark, troubleshoot, and optimize the performance of critical applications in virtualized test environments. Every virtual machine can be assigned a unique WAN access profile, and then controlled to insert latency, jitter, packet loss, and congestion. Simulate Bandwidth, Latency & Jitter, Loss.
-
Product
Emulates Winbond W78ERD2
FE-WRD2
-
* Emulates Winbond W78ERD2 * 62K Code Memory * Real-Time Emulation * Frequency up to fmax at 5V * Windows Debugger For C/C++ And Assembler * 44-PLCC Emulation Header * Target Board and Programmer Included * RS-232 or USB Interface * 64K C/ASM and 8K C++ Included
-
Product
Network Emulator
Calnex SNE-X
-
A multi-port, high-performance network emulator to drive product/application quality and reduce the cost of test with rigorous, scalable test capability.
-
Product
Low Cost Emulator
EB-ST62
-
# Supports Most of the ST62 Microcontrollers# Real-Time Emulation up to Device Frequency# 3.3V and 5V Operating Voltages# Real-Time Trace Buffer# Source-Level Debugger for C and Assembler# Unlimited Number of Breakpoints# Stack Overflow Debug Breakpoints# 8K Bytes Emulation ROM# 192 Bytes Emulation RAM# 128 Bytes Emulation EEPROM# On-Board Switches and LEDs
-
Product
Lightning "Emulator" Shield
SEN-39002
-
Arduino shield, ideal for AS3935 lightning sensor development. The lightning "emulator" generates a RF signal that mimics lightning strikes. This board is in an Arduino Uno form factor, and only uses GPIO and I2C, so can be stacked on many form factors (developed on an Uno and Mega).
-
Product
eNodeB Emulator
-
The eNodeB Emulator includes UE simulation, and can be used to test the complete LTE Packet Core or individual Core Network elements, MME, SGW, PGW. It implements all the required protocols - S1AP/SCTP to communicate with MMEs over S1-MME interface and GTP-u to communicate with S-GW over S1-U interface.
