- Virginia Panel Corporation
product
Receiver, 9025, 25 Module, EMI Gasket
310104431
The 25 Module Receiver is a rugged system devised to accommodate medium I/O. With high contact point availability, the 25 Module Receiver is suited for larger test and measurement systems. This 9025 offers a gasket for EMI applications.
-
product
Backplane Test System
402HV
Our model 402HV is the result of 25 years of high voltage / high pin count test systems experience. We produced our first high voltage system back in 1985. It was programmable up to 600 volts / 600 Mohms and had over 49,000 test points. It could test a 5k point board in less that 15 seconds. Since then we have built hundreds of high voltage test systems, with our highest voltage system capable of testing up to 2000 Volts DC / 1500 Volts AC. (One of our 600 volt systems, built in 1986 is still in operation testing boards for a defense contractor.)
-
product
Voyager Intermittent Fault Detection Tester
This family of testers is available as the portable VIFD™ tester (previously called the Ncompass-Voyager) with 128, 256 or 512 test points, and it is available as a 19” rack-mount system – the IFD & Isolation System (IFDIS™) – with thousands of test points. Testers are available from Copernicus Technology for purchase or lease. Alternatively we can provide the full test service for you and we also provide all the corresponding test accessories listed under the Test Equipment menu button.
-
product
Holiday Detector
VHD
Veer Electronics make Holiday Detector is capable to test various insulative coatings like Coal tar, Paint etc. It generates high Voltage DC for testing. When this Voltage is applied to the coated area and if pinhole or any defective point of coating is detected high voltage spark occurs on pipe or surface where we are testing. At the same time, an electronic Buzzer also beeps which gives Audio indication as well as Red colour Fault LED also glows as Visual indiction of fault.
-
product
Cable Harness Test System
Data Patterns has built high reliability Cable Harness Test Systems for large installations. These are primarily used in launch vehicle aircraft and missile level cable harness test validation. Installations with upto 20,000 lines test capability at a single location have been supplied by Data Patterns. Portable version capable handling of as small as 384 points have also been addressed.
-
product
Phasing Voltmeter/Sensor (2 in 1)
STB Electrical Test Equipment, Inc
STB unit replaces 3 separate units manufactured by competitors - line phasing, capacitance phasing and line to ground Versatile, lightweight and easy to useEach portable meter has a single rangeMeter usage: Voltage detection and phasing at capacitance test points or voltage detection and phasing on bare energized conductors (overhead & underground)Probes can be separated to be used as a voltage sensor or capacitance sensorFive position selector.
-
product
Breakout Box
T1000-62HD
Our most expansive breakout box, using dual High Density 62 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 124 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity.
-
product
Averaging Extensometers for ASTM D5656 Shear Tests
Model 4013
Jinan Testing Equipment IE Corporation
The Model 4013 extensometer meets the requirements of ASTM D5656 for measuring the strain properties of an adhesive in shear. It uses different contact point spacing compared to the extensometer shown in D5656. This makes it much easier to mount and eliminates the slippage problems associated with the design shown in the ASTM standard. The Model 4013 is available with all of Epsilon’s temperature configurations. It has a 3.0 mm (0.12 inches) full scale measuring range. The conical point contacts...show more -
product
Switches
Whether you are performing high-accuracy, low-speed measurements on a dozen test points or high-channel, high-frequency characterizations of integrated circuits, National Instruments delivers a flexible, modular switching solution based on PXI or SCXI to help you maximize equipment reuse, test throughput, and system scalability.
-
product
PRECISION GAUGE
PVX
PVX is equipped with an alpha-numeric data logger to provide increased versatility for those custom reporting needs. The high speed scan feature speeds up the inspection process by making 32 measurements per second. Remove transducer from the test material and display the minimum measurement scanned.Visual and audible alarm with hi and lo limit settings for specific application tolerances. Auto find features locates the detection point(s) and adjusts the display settings to bring the waveform into view. PVX comes complete with our Windows PC software for transferring data to and from a PC.
-
product
LiFi HotSpot Evaluation Kit
The Li-Fi HotSpot Evaluation Kit allows the establishment of an optical wireless bidirectional point-to-point full-duplex data connection over medium distances in the meter range. Data rates of up to 1 GB/s are supported at a distance of up to 5 meters. The kit consists of two Li-Fi HotSpots, two CAT-6 cables (RJ45), two external power supplies and a user manual. Users can thus get to know the technical advantages of Li-Fi technology with little effort and test and evaluate them in their own network or environmental conditions.
-
product
PXIe-8623, 4-Port, 100/1000BASE-T PXI Automotive Ethernet Interface Module
787992-01
PXIe, 4-Port, 100/1000BASE-T PXI Automotive Ethernet Interface Module - The PXIe-8623 is a 100/1000BASE-T unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module that helps you develop applications with the NI‑XNET driver. With the PXIe-8623, you can develop applications that require Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8623 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboar...show more -
product
Damp-Heat Tester
King Design Industrial Co., Ltd.
1. Technical index:*Power: 380V, 3-, 50/60HZ 110A*Temperature range: 50°C~120°C*Humidity range: 20%~95% RH*Accuracy: 1) temperature ± 0.3°C；2) humidity ± 2.5% RH*Uniformity: 1) temperature ± 2.0°C；2) humidity ± 3.0% RH*Uniformity test: measured at T=85°C, RH=85%; set 9 points for temperature measurement and 2 points for humidity.*Inner wall is above 50 cm; within 20 min after temperature/humidity meets the setting value, the distribution uniformity of temperature/humidity can meet the aforesaid requirement.
-
product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781420-11
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
Automatic Wire Test Set
AWTS
The Automatic Wire Test Set (AWTS) is automated test equipment that aids wiring diagnostics of electrical and electronic devices. The Test Control Unit (TCU) uses resistance measurements, capacitance measurements, and AC/DC voltage measurements to perform continuity, insulation, and isolation tests. The AWTS Laptop CPU, hereafter referred to as CPU, controls the AWTS. The Eclypse Language Integrated Test Environment (ELITE) is application software that controls the TCU. The majority of the hardw...show more -
product
Alternate 17.00 (482.00) - 35.00 (992.00) Switch Probe
MSP-3C-1
Current Rating (Amps): 3Average Probe Resistance (mOhm): 50Alternate Force at switch point: 23.3 (661)Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 140Full Travel (mm): 3.56Recommended Travel (mil): 85Recommended Travel (mm): 2.16Mechanical Life (no of cyles): 100,000Overall Length (mil): 2,140Overall Length (mm): 54.40Switch Point (mil): 30Switch Point (mm): 0.76
-
product
RMC
Receive Multicoupler (Rx AIT)
*Provides a common receive distribution point for multiple basestations*Each Cellular and PCS unit supplies 8 ports and supports 2 channels*The single 1U tray includes integrated Bias- T and test ports*QMA receive connectors provide quick and sure connections
-
product
SWB-2812, 16x9, 1 A, Reed Matrix Module for SwitchBlock
781420-12
16x9, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2812 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
Reference Thermometers
Our Reference Thermapen takes lab accuracy into the field. Each unit is factory calibrated at 5 test points and includes a UKAS accredited calibration certificate with test data. A true "system calibration" is performed matching its Platinum RTD sensor and the built-in electronics so all errors are included in the spec.
-
product
CAM/TRAC Test Kits
Series 43
The GR Series 43 CAM/TRAC®1 kits, utilizing the patented CAM mechanism, offer precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance. The Series 43 provides interface compatibility by using a 12 position, GR2270 style I/O block interface. This interface accepts the industry standard I/O, power, and coax blocks.
-
product
802.11a,b,g RF Shielded Test Enclosure
JRE 0814-A
Testing tall devices? The 0814-A stands up to any test up to 18 GHz! Featuring a wide swing open door with durable latch handle, this enclosure is ideal for testing IEEE 802.11 a,b,g devices such as; WLAN, VoIP, access points and other RF devices.
-
product
Automatic Asphalt Content Tester
4000g sample capacity, integrated +0.1gm accuracy weighing scale, High temperature ceramic filtration system and afterburner for accurate measurement of bitumen content in asphalt mixes. Automatic operation through user defined automatic end point detection and 24 hour start timer. User defined control of furnace chamber temperature from 200 – 650oC, Digital display and printing of test data through bright LED displays and integrated printer, Software activated mechanical door lock to prevent door from opening during test process and cutting off power from the heating elements upon opening the door. Operates on Single Phase, 220V, 50 Hz, 20 Amp and consumes less than 5000 W.
-
product
Low Voltage Test System
CKT T1
The CKT T1 is a compact size solid-state test system featuring 128 test points.
-
product
Breakout Box
T1000-15
T1000-15 breakout box with dual 15 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 30 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
-
product
PXI-6733, 16-Bit, 8-Channel, 1 MS/s PXI Analog Output Module
778512-01
16-Bit, 8-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6733 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response tests (including acoustic distortion testing) and simulation (such as three-phase power simulation). In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PX...show more -
product
Monitor and Test Video Quality
Torque Electronic Couch Potato (ECP)
The ECP is designed to monitor and test video quality of experience. This affordable, compact, palm-sized monitoring probe monitors true customer viewing experience by providing measurements from the end users’ point of view, after the STB. Scanning through available channels or navigating through interactive content menus via an external IR blaster, the ECP provides a single dashboard highlighting service quality across all channels.
-
product
Audio Test Software
1. Distortion free stimulus even the equalized stimulus.2. Unlimited channels acquisition and processing. (Hardware limited)3. Human correlated listening test(Bark Scale intensity chart). (Requires large memory)4. Hi Res intensity chart for buzz/pop detection. (Requires large memory)5. Auto equalization method with target dBSPL accuracy.6. TCP client for test framework integration.7. Easy limits and logs development.8. Easy logs visualization module.9. Auto waveform alignment and triggering.(Upt...show more -
product
PCB Test Fixture Kits
Emergent's fixture kits are available in bottom and double sided probing versions. They are fully scalable, from compact benchtop testers to full size multi-UUT production floor models. The removable, interchangeable plate design allows you to easily add and move test points, or swap out plates to test a completely different product. Each kit comes with a standard linear collapse over-clamp. A cam-follower closing system can be specified for higher force applications. Our fixture kits are manufactured using industrial grade phenolic laminate, which is similar to G10 in hardness and strength but easier to machine. The standard kit comes pre-assembled with blank plates for machining.
-
product
PXI High-Density Multiplexer: 64-ch, 2-Wire, 100Vrms/1A, Reed Relays
M9101A
The M9101A, a high-density, 64-channel PXI multiplexer routes many different channels to a single point. The switches operate in a break-before-make mode that ensures no two points are connected at the same time or, if needed multiple channels can connect simultaneously. Ideal for routing multiple analog signals to a measurement device in automated test environment (ATE) or data acquisition systems. Each channel switches a high and a low for 2-wire switching up to 100Vrms, with up to 10W of power. Connection options include the durable connector block or the standard cable connections.
-
product
CAM/TRAC Test Kits
Series 40
The CT Series 40 CAM/TRAC mechanical kits, utilizing the patented CAM mechanism, offer precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance.
-
product
SWB-2833, 4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-33
4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2833 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under...show more
