Test Systems
group of interoperable devices whose integration perform a common test purpose.
See Also: Systems, Equipment, System Integrators, System Test, System Integration
-
product
Sapphire/SIC Wafer Flatness and Surface Appearance System
FM200
Sapphire/SIC wafer flatness and surface appearance system provide a previous surface flatness testing solution, though non-contract lighting testing to record the whole information of the surface, rapid and fast measurement for various of surfaces, line and all kinds of surface information.
-
product
Wafer Level Multi-Die Test System
ITC55WLMD
The ITC55WLMD series of test systems has been developed by ITC to be stand-alone UIL test systems configured specifically to test on wafer. The systems include an ITC55series UIL tester and inductor box, a current limiter module and a system controller
-
product
Software for System-Based Protection Testing
RelaySimTest
RelaySimTest is a software solution for system-based protection testing with OMICRON test equipment that takes a novel, future-oriented approach: the test is independent of relay type and relay manufacturer and the often very extensive parameter settings. Instead, it completely focuses on the correct behavior of the protection system. This is made possible by simulating realistic events in the power system.
-
product
PXI 8x9 RF Matrix 250MHz 75 SMB
40-725-721
The 40-725 is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz (50Ω version). The 40-725 is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connections, these disconnect the matrix from the external test fixture maximizing isolation and RF performance.
-
product
Minirator
MR-PRO / MR2
The Minirator MR-PRO provides a full set of analog audio signals including sine wave, pink noise, white noise, delay test signal, polarity test signal, stepped sweep and continuous sine sweep. Further, a set of wav-files, useful for system optimization, is stored in the internal flash memory. Add your own personal favorites to this set.
-
product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 62.1Ω
40-252-111
The 40-252-111 is a programmable resistor module with 2 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
Circuit Simulation Software
Proteus Virtual System Modelling (VSM) blends mixed-mode SPICE simulation with world leading fast microcontroller simulation. It enables rapid prototyping of both hardware and firmware designs, in software! Design, Test and Debug your embedded projects in the Proteus electronic circuit simulator before a physical prototype is ordered. Agile development for the embedded systems workflow.
-
product
SAS Protocol Test System
M124A
The SAS Sierra M124A Protocol Test System is Teledyne LeCroy's 7th generation protocol analyzer system that provides 100% accurate protocol capture of both SAS (SAS 3.0) and SATA (SATA 3.0). The industry's most widely used test platform for SAS and SATA features unmatched analysis and debug capabilities to help pinpoint problems at every layer of the protocol.
-
product
Rotary Table Handler
6000 Series Rotary Handler
Rotary table handlers are an excellent choice for PCBA or product – level test, programming, part marking, automatic part rejecting, and vision inspection in order to satisfy manufacturing applications that require high throughput. Rotary table based systems used in production can also help reduce the impact of load and unload times for the operator, because the device-under-test (DUT) automatically moves to the next cell within the station as each DUT is loaded. Circuit Check’s 6000 series hand...show more -
product
Eddy Current Dynamometer
EC Series
Specifically designed for small displacement diesel engines, the Eddy Current (EC-Series) engine dynamometer features in-line eddy current absorption units in a robust, compact frame. The air-cooled eddy current absorbers eliminate the need for an expensive water recirculation system and most engines being tested can be cooled with a standard closed-circuit radiator system. This compact air-cooled design results in a minimal environmental impact and the ability to be easily relocated with no need for a permanent installation. When combined with PowerNet LT, our fully automated dynamometer control system, all of your testing needs can be performed at the touch of a button.
-
product
CableEye Generic Surface Mount & TH Board | Cable & Harness Tester
CB51
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with solder pads to accept both aligned and staggered, 1.25mm and 1.5mm pitch, surface mount and through hole (TH) connectors, the board addresses any market with a demand for board-to-board connections. Rated to 700Vdc/500Vac, the CB51 may be used on all CableEye models.
-
product
Battery Load Tester
BT-100
Schumacher Electric Corporation
FOR EVERYDAY DIY USEEasy to operateTest load, battery condition, starter motor draw and complete charging system diagnosis.Works on 6 and 12 volt batteries50 amp load test for 6 volt batteries100 amp load test for 12 volt batteries Tests 6 and 12 volt batteries ─ up to 1000 CCATop-mounted rocker switch for easier operationSuper-grip, heavy-duty color-coded battery clampsEasy-to-read meter ─ accurate and shock resistantBaked enamel, steel case ─ ventilated to keep coolRubber insulated carrying handle ─ for comfort and safety
-
product
PXI BRIC8 FIBO Matrix Dual 18x4 3pin brkout
40-595A-008
The 40-595A is a matrix module based on the BRIC format that is designed for fault insertion applications in safety critical testing. As with other BRIC modules the matrix size can be scaled to suit the user application. The 40-595 has a very high current rating of 10 Amps, ideal for higher power systems, and can be used as a conventional matrix.
-
product
Mixed Signal Automated Tester
MSAT
Whether you are testing radar systems for the Department of Defense (DoD), or the next actuator circuit card for aircraft landing systems, ARC’s Mixed Signal Automated Tester (MSAT) offers flexible automated testing capabilities for nearly every budget.
-
product
Efficient All-In-One Test Solution for Low-Cost IoT Devices
KT RFCT 2400
The low price point creates a cost effective means for testing wireless communication units, while generating a favorable cost to performance ratio.The calibrated RF test system has a small footprint, integrating seamlessly into test system infrastructures via a single Ethernet connection. GPIOs control the DUT and peripherals. The test system enables communication interfaces like SPI, I2C, UART and CAN. Simple Go/No-Go tests can be performed in parallel. The KT-RFCT 2400A features a 70 MHz to ...show more -
product
Battery Extra Load Units
Performing capacity/discharge test on a high-capacity battery may be challenging since high requirements are set on the discharge system. In cases when discharge test times need to be reduced, high load capacities are required from the discharge system. The battery extra load unit BXL is an additional load unit designed especially for this purpose.It is primarily used with BLU battery testers. However, the unit is a universal add-on device. This means it can be used as an additional load with an...show more -
product
IOL & Power Cycling Test Systems
Our IOL & power cycling systems increase measurement quality and throughput and reduce testing costs on an open platform. The focus is on seamless monitoring and precise determination of all parameters of each DUT. In addition, the systems are equipped for the special requirements of wide-bandgap technology.
-
product
PCI/PCIe Bus Extenders
Enables PCIe x16/x8/x4/x2/x1 boards to be rapidly tested, removed and swapped without having to reboot or power down the host system. Enabling rapid production testing and engineering debug, the hot insertion, current reporting, overcurrent indication and limiting and voltage margining capabilities make this board the highest performance PCI-e bus extender in the industry.
-
product
USB Power Sensor - 100 MHz To 8 GHz, Average, Peak (Pulse), Pulse Profile
GT-8552B
The Spanawave/Giga-tronics GT-8550B USB Power Sensors offer easy-to-use high-performance RF and microwave power measurement. High dynamic range and high accuracy make these sensors ideal for testing in wireless communication applications and Defense EW systems. The GT-8550B series feature a ruggedized body and fast measurement speed. These broadband power sensors provide easy-to-use, fast, accurate power measurement for R&D laboratory, manufacturing test and field installation and maintenance applications.
-
product
PXI High Density Precision Resistor Module, 3-Channel, 3.5Ω to 102kΩ
40-298-140
The 40-298-140 is a high density programmable resistor module with 3 channels which can be set between 3.5Ω and 102kΩ with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
RF & ECM Test Set
MS 1109
The RF Tester is a computer-controlled system used to test the RF Unit, Logic Unit (ECM) and its modules.
-
product
Antenna Test Facility
Raytheon’s Antenna Test Facility (ATF) provides state-of-the-art measurement capabilities to assist in the development of advanced antenna technologies for a variety of airborne and space applications such as advanced radar and communication systems. The ATF is available for use by Raytheon businesses as well as other companies that design and prototype new and experimental antennas.
-
product
Cots Boards
Built in strict adherence to open architecture standards, Data Patterns designs COTS module products which are used in today's rugged applications and automatic test equipment platforms. Open standard form factors include cPCI, FMC & XMC, IP, MM, PCI, PCMCIA, PMC, VME, VPX and VXI.A portfolio of 'Off the Shelf ' products for testing and on-board applications have been developed by Data Patterns. COTS boards developed have been sold to many customers, in India as well as Europe and North Amer...show more -
product
PXI Hybrid Coaxial Switch: DC To 40 GHz, Single SP6T, Terminated
M9157CH40
M9157CH40 operates from DC to 40 GHz, providing a low-cost operation switching solution for measurement and automation of Automatic Test Equipment (ATE) systems without compromise in the RF performance. It is being used in applications such as ATE, RF communication and RF parametric measurements where a rugged switching module is needed for signal routing. Typical switching applications for multiport coaxial switches include signal routing to a single input - to multiple instruments and routing of multiple input signals.
-
product
Catalysis and Thermal Analysis
A system for catalyst characterisation, reaction testing, kinetic and thermodynamic measurements.
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 127 Ohm - SPST
50-294-112
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Software Development
In support of system, test and our tooling design, our software development team is ARC’s primary advantage in providing the superior performance in hardware (electrical), mechanical and software cohesiveness. The software team at ARC literally brings all of it together.Whether you want to leverage one of our standard platforms, such as TestCentre or harness the power of the process editor in our PVS software to build up your custom workflow, most customers are impacted by the power and scalabil...show more -
product
Fire Control System
MS 1120
PCI Based BTA is used to test FCC System Processor (8086) & Analog Boards. This system consists of a PC-AT, Digital Input / Output (DIO) Board and Analog Input / Output (AIO) Board to provide the necessary input/output signals to/from the board to be tested.
-
product
Multiplex Optical Maintenance Meter
LS280
LS280 is used to measure optical maintenance factor for high power LEDs, LED module, LED bulb or other LED luminaries. It is the important measuring equipment for performing the reliability of illuminants. • Freely set the time interval and time extent for automatic measurement • LCD Display, connect with PC via RS232 and English version software. • The test results can export Excel or PDF format and easy to compare. It can be saved by LS280 software or by USB directly. • The engineer can do LE...show more -
product
Test System Elowerk
eloZ1
The eloZ1 Manufacturing Defects Analyzer is an in-circuit tester of the latest generation. It reliably finds connection errors and assembly errors in electronic assemblies. The test electronics can be integrated both in table systems and in inline systems.
