-
Product
Pinless Moisture Meter
-
A large number of boards can be scanned quickly without leaving pin holes. No effort is needed to insert pins into hard wood.Pinless moisture meters measure lower moisture contents in hardwoods than pin moisture meters.
-
Product
3D Scanner
Raptor3DX
-
Raptor3DX is a hybrid type optical scanner, enabling both the automatic and stationary modes for users. The compact, detachable scanning sensor acts as a powerful sensor engine when as automatic mode; a flexible scanner itself when used as stationary mode, providing three FOV in one.
-
Product
Spectrometers
OCEAN FX
-
The next innovation in miniature spectrometers from Ocean Optics — Ocean FX™ — offers high-sensitivity CMOS detector performance, acquisition speed up to 3,000 scans per second, and a robust communications module that accommodates Ethernet and Wi-Fi. The new spectrometer is ideal for UV-Vis applications in food and agriculture, where acquisition speed helps with food sorting and processing; biomedical sciences, especially for absorbance measurements requiring enhanced UV sensitivity; and security and authenticity, where added communication interfaces enable simpler point-of-use instruments. Also, the onboard buffering feature ensures data integrity during kinetics measurements.
-
Product
Sputter Coater & Freeze Fracture Solutions
-
To obtain high-quality images of samples with scanning (SEM) or transmission electron microscopy (TEM), your samples need to be conductive to avoid charging. If a sample does not have a high enough conductivity, then you can quickly cover it with a conductive layer using the method of sputter coating. Also, a carbon or e-beam evaporator coating can be used. Such coatings protect the sample, allow enhancing of the EM image contrast, or can act as a TEM-grid support film for small scale samples.
-
Product
eDAK For MAC Panel
JT 2147/eDAC for MAC Panel
-
The JT 2147/eDAK is a new variant of the JTAG Technologies QuadPOD signal conditioning interface specifically designed for use within a MAC Panel ‘Scout’ mass interconnect interface. The unit integrates both the JT 2148 transceiver circuitry plus four independent, programmable TAP modules (two of type JT 2149 and two of type JT2149/MPV) on a single board that matches the MAC Panel Direct Access Kit (DAK) form factor. Overall this configuration offers four Test Access Ports, 64 Digital IO Scan channels and reconfigurable (SCIL) capabilities
-
Product
Analog Input Module, 16-bit A/D
IP330A
-
The IP330A has many features to improve your overall system throughput rate. You can scan all channels or define a subset for more frequent sampling. Burst mode scans selected channels at the maximum conversion rate. Uniform mode performs conversions at user-defined intervals. Both modes can scan continuously, or execute a single cycle upon receiving a trigger.
-
Product
PON Fiber Optical Monitor System
PON FOMA
-
PON FOMA ( PON Fiber Optical Monitoring Alarm System) is integrated RTU ( Remote Test Unit )、Center Monitoring Server and its management software to be integrated operation、remote control、periodic fiber scan、predictive analysis and support the instant fiber with status information and alarm warning, accurate of long-term fiber data record, fiber analysis and management. RTU monitoring station is embedded Linux system which is with the advantage of high security, stability, efficiency.
-
Product
Ambient Pressure Photoemission Spectroscopy With Nitrogen Environment
-
The APS04-N2-RH incorporates a tuneable deep ultra-violet (UV) source outputting 3.4 - 7.0 eV, for absolute work function and highest occupied molecular orbital (HOMO) measurements, a surface photovoltage spectroscopy (SPS) module outputting 400 - 1000 nm for Voc and Eg measurements, together with a 50 x 50 mm scanning area for planar relative work function measurements (Fermi level).
-
Product
Phased Array Acquisition and Analysis Software
Prelude
-
Prelude is a powerful and flexible software package. At TPAC, we understand our customers have a heavy investment in scanning equipment. With this in mind, we have developed a software suite that is adaptable and complimentary to your existing devices.
-
Product
Gate Scanner
SR200`
-
Stanford Research Systems, Inc.
The SR200 Gate Scanner module is designed to automate waveform recovery with the SR250 and SR255 Gated Integrator modules. Waveform recovery is done by slowly scanning the gate of the integrator over the waveform of interest.
-
Product
Confocal FLIM System
DCS-120
-
*FLIM Upgrade for Existing Conventional Microscope*Two Fully Parallel TCSPC FLIM Channels*Compact bh Simple-Tau or Power-Tau System*Scanning by Fast Galvanometer Mirrors*Channel Seperation by Dichroic or Polarising Beamsplitters*Individually Selectable Pinholes and Filters*One or Two BDL-SMN or BDS-SM ps Diode Lasers*Two Fully Confocal Detection Channels*Two HPM-100-40 GaAsP Hybrid Detectors*Optional: Two HPM-100-06 Hybrid Detectors, IRF Width < 20 ps FWHM*Optional: HPM-100-50 Hybrid Detectors for NIR FLIM*Optional: Multi-Wavelength FLIM*Excellent Time Resolution: Electrical IRF Width 6.5 ps FWHM*Time Channel Width Down to 813 fs*Megapixel FLIM, Up to 2048 x 2048 Pixels at 256 Time Channels*Simultaneous FLIM/PLIM*Wideband Version, Compatible with Tuneable Lasers*Electronic Pinhole Alignment*Z-Stack FLIM Acquisition with Zeiss Axio Observer Z1*Optional: Spatial Mosaic FLIM via Motorized Sample Stage
-
Product
LAN Check With Tone Generator
PH-01
-
The LANCHECK consists of two modular units, a tester and a remote terminator. The modular design enables the tester to be used for local loop-back testing of patch cable or remote testing of pre-installed premise wiring. The LANCHECK makes it easy to recognize opens and shorts within a cable as well as identify reversed and miswired cables. It can verify a cable up to 2,000 feet in length. Furthermore, it comes with shielded connectors, which enables the testing of shielded twisted pair (STP) cables. It also features convenient Auto Scanning and precision Manual Scanning modes.
-
Product
2-Sensor SWIR Line-Scan Cameras
Wave Series
-
The Wave Series camera is a 2-sensor prism line scan camera capable of sensing Short Wave InfraRed (SWIR) light.The camera is based on Indium/Gallium /Arsenide (InGaAs) sensor technology and combined with JAI’s prism line scan technology, making it capable of delivering dual-band imaging in the SWIR light spectrum (900 – 1700 nm).
-
Product
Side Scan Sonar for Gavia AUV
-
Several brands of Side Scan Sonars (SSS) can be installed on the Gavia in the control and communication module. Available frequencies range from 600 kHz to 1.8 MHz in both single and dual frequencies The SSS accumulates data at a rate of up to 40 megabytes per 1000 meters. A 16-gigabyte flash disk is provided standard for storage of SSS data, with larger disks available optionally.
-
Product
High-efficiency Fiber Stretcher
PZ2
-
The PZ2 provides the most extensive stretch of our stretcher product family. It is a fiber wound piezoelectric element for use in a wide range of optical interferometric measurement and sensing system applications. Typical uses include open loop demodulation, sensor simulation, white-light scanning interferometry and large angle modulation of interferometric phase. The PZ2 is ideal for use in OCT [Optical Coherence Tomography] and OCDR [Optical Coherence Domain Reflectometry] applications requiring scattering or boundary definition measurements.
-
Product
ATPG with Embedded Compression
TestKompress
-
TestKompress is an automatic test pattern generation (ATPG) tool that provides the highest quality scan test with the absolute lowest test cost. TestKompress has an industry-proven ATPG engine that applies effective fault models to your entire logic design. Manufacturing test costs are held in check by an award-winning test pattern compression technique called Embedded Deterministic Test (EDT).
-
Product
Line-scan Camera
-
The Avaatech XRF Core Scan can also be equipped with a high-resolution line-scan camera that allows to obtain detailed pictures of the sample material, including color data. The current generation camera is the JAI LT-400 CL-F Color Line Scan Camera.
-
Product
kSA MOS Ultra/ThermalScan
-
The kSA MOS UltraScan and kSA MOS ThermalScan systems are ex situ, flexible, high-resolution scanning curvature, bow, and tilt-measurement systems.
-
Product
Boundary Scan Program Development Service
-
No need for test fixtures. Integrates product development, production test, and device programming in one system. Test and Programming data can be reused in Production. Fast test procedure development. Reduced inventory management. Eliminates or reduces ICT usage time. Pre-production testing can begin as soon as prototype is released.
-
Product
4-Sensor R-G-B (Prism) Color Line Scan Cameras
-
In addition to 3-sensor prism line scan cameras, JAI's Sweep+ Series includes a set of 4-sensor multispectral line scan cameras designed to simultaneously capture R-G-B image data in the visible light spectrum and image data in the near infrared (NIR) light spectrum.
-
Product
Automated Optical Inspection System
AOI Series
-
Perform visual inspections of printed circuit boards (PCB) during manufacturing in which a camera is used to scan the board in extremely fine detail to check for any defects or failures.
-
Product
Scanning Probes
-
Scanning probes can acquire several hundred surface points each second, enabling measurement of form as well as size and position.
-
Product
Optical Measurement
-
• Vertical optical measuring machine for static and dynamic measurement of various elements on small cylindrical parts.• The parts can be mounted between two centres or held in place using various accessories.• Attractive design and robust construction with many new features: New touch screen control panel for easy operation directly at the workplace, bi-telecentric optical system, high resolution CMOS camera, precision sliding headstock with integrated and protected daily standard, quick and easy accessory changing system, integrated temperature sensors, dynamic LED indicator of the general status of the measured part (GO/NG) and operator messages. Equipped with an exclusive optics tilting system.• Machines specially designed to measure threads such as, parallel, trapezoidal, conical, round, square, conical, worms, ball screws, bone screws, dental implants, etc.• Reflex SCAN+ concept for measuring parts without prior programming at the touch of a button• Delivered complete with a PC and the Reflex SCAN+ software, which allows a multitude of elements to be measured easily and intuitively.
-
Product
Safety Laser Scanner
-
Leuze electronic GmbH + Co. KG
Thanks to the configurable protective and warning fields, safety laser scanners can be used versatilely for danger zone and access guarding. Their compact design makes them ideal both for stationary and for mobile applications. Our RSL 400 safety laser scanners are characterized by their performance, robustness and easy handling. Thanks to its high operating range of 8.25 m and a scanning angle of 270°, it can monitor even large areas. The series also includes models for integration via PROFIsafe/PROFINET interface and models with data output for the navigation of automated guided vehicles.
-
Product
Scanning Electron Microscopes
SEM
-
Scanning Electron Microscopes (SEM) scan a sample with a focused electron beam and obtain images with information about the samples’ topography and composition.
-
Product
Semi-automated Metrology System
-
Full wafer surface scanning for thickness, thickness variation, bow, warp, sori, site and global flatness
-
Product
3D Metrological Software
InnovMetric PolyWorks
-
Powerful metrological software which can effectively process vast amounts of data from 3D scanners in real time. Due to its modular architecture the software covers a large number of applications: one-point inspection by touch measurement systems, scanned data processing and data comparison to CAD models or complete reverse engineering – CAD model creation.
-
Product
2-Phase Stepper Drives Based On EtherCAT Field Bus
Nu-Step DA Series
Stepper Driver
The ADLINK Nu-Step DA Series is a stepper driver based on the EtherCAT bus featuring a 32-bit ARM processor and advanced variable current and frequency conversion technology. The driver generates less heat and motor vibration for more stable operation. It not only supports the standard EtherCAT specification, but also supports table comparison triggers for automated optical inspection (AOI) and linear comparison triggers for line scanning.
-
Product
Boundary Scan
TurboBSD
-
TurboBSD is SynTest high-performance Boundary Scan Designer. It is 100% compliant to the IEEE 1149.1 Boundary Scan Standard. TurboBSD performs Boundary Scan logic synthesis, creates BSDL (Boundary Scan Description Language) file, and generates Boundary Scan test patterns
-
Product
RF Safety Monitoring
MVG EME Guard XS 6GHz
-
The EME Guard XS is an RF measuring device to alert workers near RF emitters for protection of climbers and other RF-exposed workers. It continuously scans for electromagnetic waves and, via its built-in alarm and visual system, alerts users whenever the acceptable pre-selected limits have been exceeded. This RF Safety PPE is extremely easy to use and supports a safer working environment in the areas of installation and maintenance.
