AXI
1) Advanced eXtensible Interface 2) Automated X-ray Inspection
See Also: Automated X-ray Inspection
-
Product
Entry-Level 4-Axis Servo & Stepper Motion Controller
PCI-8134A
Motion Controller
The PCI-8134A is a 4-axis entry-level motion controller. A PCI interface provides plug-and-play capability for easy maintenance, and supports up to 12 cards in one system, to control 48 motors. The PCI-8134A provides pulse train command output up to 2.4MHz and encoder input up to 2.4MHz in 4xAB phase mode. Programmable acceleration and deceleration allows flexible programming of in-house applications, and dedicated motion I/Os shorten system installation. The PCI-8134A also supports 2~4 axis linear interpolation for simplified synchronous motion. The PCI-8134A is a cost-effective motion controller enabling implementation and control of most of point-to-point, conveyer, and load-and-unloader applications.
-
Product
Axis Play Tester
LMS 20.0 | VP 425017
-
Maschinenbau Haldenwang GmbH & Co. KG.
The LMS 20.0 axis play tester is used to reliably determine defects and wear on steering parts, wheel bearings, suspension and suspension by means of counter-rotating transverse and longitudinal movement of the test plates. The built-in hydraulic drive ensures a powerful and even movement of the test plates. An automatic mode and other different operating modes make the LMS 20.0 easy to use.
-
Product
Light Distribution Photometer Goniophotometer
LCG-1600
-
Shenzhen Chuangxin Instruments Co., Ltd.
LCG-1600 Goniophotometeric System carries out measuring methods of fixed location and rotating luminaires. The measured luminaire is installed on the two-dimension rotating table, using “+” laser to make the luminaire lighting center superposed with the rotating center of rotating table. The mechanical equipment allows turning the tested luminaires around a vertical axis and a horizontal axis. When tested luminaires turn around horizontal axis, the detector which is at the same level with rotating table will measure the intensity of each direction at this surface. When rotating with vertical axis, the detector will measure the intensity at the vertical surface. The vertical and horizontal axis can be rotated continuously at ±180° or 0~360°. According to the measurement requirements, the system can be operated in C-γ coordinates. When getting intensity distribution data, computer will calculate other photometric parameters automatically.
-
Product
Goniophotometers
-
Instrument Systems Optische Messtechnik GmbH
All goniophotometers are designed as Type C with a horizontal alignment of the optical axis (turning luminaire configuration). Each goniometer sets benchmarks in its class for precision, reliability and handling. If these goniophotometers are combined with a spectroradiometer from Instrument Systems, they are able to determine not only photometric data but also spectral quantities, such as color coordinates, color temperature, and even color rendering index as a function of angle.
-
Product
Three Axis Accelerometers
TAA
-
The Inertial Labs MEMS TAA-308, TAA-315 and TAA-340 are the third generation of the Inertial Labs MEMS, three-axis high-precision accelerometers released in a stand-alone design. The TAA-308, TAA-315 and TAA-340 are revolutionary, compact, self-contained, strapdown, Navigation-grade Accelerometers that measure linear accelerations with high precision due to their unique design and developed by Inertial Labs over last 20 years several significant know-know and technics in calibrations of inertial sensors. Measured by TAA Accelerometers accelerations are determined with low noise and very good repeatability for both motionless and dynamic applications.
-
Product
Angular Reflector
10771A
Accessory Kit
The Keysight 10771A Angular Reflector, used in the Keysight 5530Laser Calibration System, is ideal for precision calibration applications. Paired with the 10770A Angular Interferometer, it is used to measure pitch and yaw motions along each axis that a machine tool or measuring machine travels. The system can help quickly locate and evaluate unwanted angular motion.
-
Product
Shake Table Testing
-
Response Dynamics Vibration Engineering, Inc.
Shake table testing is often used in prototype analysis, failure analysis, shipping vibration testing and vibration sensitivity testing. We know what boundary conditions are vital for effective testing, how and where to instrument the system, how to deal with for off axis excitation (often not accounted for), and make the most efficient use of testing time. Let us have a look at your system and any specified vibration criteria before the shake test is designed. We can interpret the criteria, make sure it is applied appropriately, and make recommendations that will save valuable time and expense.
-
Product
PXI Fault Insertion Matrix Modules
-
All of our fault insertion matrices feature a breakout arrangement that allows faults to be attached to the sensor lines via the Y axis. This includes the breaking of a connection or the adding of a series defect – all of which can simulate connectivity problems in the system. The three pin breakout versions allow the connection to be swapped for a “bad” sensor simulation.
-
Product
SparkFun Triple Axis Accelerometer Breakout
ADXL335
-
Breakout board for the 3 axis ADXL335 from Analog Devices. This is the latest in a long, proven line of analog sensors - the holy grail of accelerometers. The ADXL335 is a triple axis MEMS accelerometer with extremely low noise and power consumption - only 320uA! The sensor has a full sensing range of +/-3g.
-
Product
Electric Servo Motor Type 1 Axis Vibration Tester
-
In Addition, The System Configuration Requires At Least 3 Main Units, A Control Panel, And A Controller, And Does Not Require Hydraulic Units Or Blowers. The Exciter Can Perform Standard Tests And Performance Tests Required For Automobile Seats Based On An Electric Servomotor Type Multi-Axis Vibration Tester.
-
Product
High Resolution Digital Radioscopy Compact System
FastRadio
-
Real time high resolution digital radioscopy. Motorized zoom axis. Horizontal flat sample holder. Very small footprint.
-
Product
Angular Optics Kit
55281A
Accessory Kit
The Keysight 55281A Angular Optics Kit adds pitch and yaw measurement capability to the 5530 Laser Calibration System. Ideal for use in precision calibration applications, it includes the 10770A Angular Interferometer and the 10771A Angular Reflector. Together the high-accuracy plane mirror interferometer and the angular reflector measure pitch and yaw motions along each axis that a machine tool or measuring machine travels. Results are displayed directly in arc-seconds or in mm/mm (in/in).
-
Product
Spinstand Automation For Media Testing With XY-Positioning
V2002
-
Guzik V2002 XY-positioning spinstand uses the X and Y coarse positioning stages actuated by linear motors and the micro-positioning stage actuated by the piezo element aligned with X coordinate axis to place the tested head on the specified track. WITE32 software converts the requested track number and skew angle into X and Y coordinates.
-
Product
CNC Rotary Axis Calibrator
API Swivelcheck
-
API SwivelCheck is light-weight & comes with a convenient carrying case to easily transport & install on a variety of CNC machines.
-
Product
Load Button Load Cells
-
Interface’s load button load cells are designed for customers who require the measurement of compression forces in a very low height space. They are designed to provide the most accuracy in as little space as possible. The smaller ConvexBT or LBMU can fulfill the need for force measurements at a very respectable precision level that is enough for most applications. Diameters range from ⅜ of an inch to just over 3 inches, with heights from ⅛ of an inch to 2 inches. The shaped load button has a spherical radius to help confine misaligned loads to the primary axis of the cell.
-
Product
Solvent Resistance Tester
NRJ-100
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.4-2008/IEC60851-4; Inspection standard: JB/T4279.10-2008Used to detect the solvent resistance performance of enameled round wires and flat wires with nominal conductor diameter above 0.250mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Pencil push unit would automatically lay down pencil and move ahead, lift pencil and automatically return to initial position;Used in combination with JRK-60 solvent thermostatic controller;Automatic pencil sharper can sharpen pencil tip to be 60° symmetrical to its axis;
-
Product
Cladding Alignment Splicer
95EA
-
OFS-95EA optical fiber fusion splicer is designed with high-speed image processing technology and special precision-positioning technology. It will automatically finish the whole fiber fusion process in 9 seconds by fast mode, and splice loss is lower than 0.02dB for single mode fiber. 3.5-inch LCD, dual CMOS monitors, X and Y axis separately display or simultaneously display, thus different fusion stages can be showed clearly. It is compatible with ITU-T SM/MM/DS/NZDS/ED fiber, and is equipped with 4-in-1 holders and SOC adapter.
-
Product
Transmission / Reflection Measurement
-
Measure spectral transmittance and reflectance of optical elements such as lens, plate glass, filter, reflector, prism and so on.The wavelength range is 350 to 1100 nm as standard and 220 to 2000 nm as an option.Reflection measurement of a general spectrophotometer can only measure several types of fixed angles, but in this device the incident angle of the sample at the time of reflectance measurement is variable at an arbitrary angle and the minimum incident angle at reflectance measurement is 15 ° ( Optical axis angle 30 °) can be set up.
-
Product
Single Axis Interferometers
-
Linear, single-beam, and plane mirror interferometers measure motion on a single axis.
-
Product
Coordinate Measuring Machines
VideoCheck® HA
-
Fixed bridge CMM for highest precision and flexibilityIntegrated Werth Zoom® provides advanced capabilities for automatic measurement even for workpieces with minimal contrastIntegration of additional sensor units to a multisensor system guarantees higher flexibility and measuring speedModular structure guarantees customized solutions for individual applicationsOptional integration of a high precision air bearing rotary / rotary tilt axis
-
Product
3-Component Quartz Force Rings
260 Series
-
Three-component quartz force ring sensors are capable of simultaneously measuring dynamic force in three orthogonal directions (X, Y, and Z). They contain three sets of quartz plates that are stacked in a preloaded arrangement. Each set responds to the vector component of an applied force acting along its sensitive axis. 3-component ring force sensors must be statically preloaded for optimum performance. Preloading provides the sensing elements with the compressive loading required to allow the proper transmission of shear forces. Versions are available with ranges up to 10k lb (45k N) in the z-axis (perpendicular to the top surface), and up to 4000 lb (18k N) in the x-and y (shear) axes. Both ICP® and charge output styles are available.
-
Product
Laboratory Instrumentation
-
Haydon Kerk Pittman has developed motion control systems used in: multi-axis sample management systems requiring high performance and reliability to meet high duty cycle requirements; microscopy stages demanding high precision positioning in multiple axis simultaneously; motion systems for automatic pipetting which requires very accurate motion for aspiration and dispense modes helping to eliminate manual pipetting errors.
-
Product
Reference Antennas
Type NRD
-
Reference antennas are precision dipole antennas that offer a fixed 2.15 dB of gain over an isotropic antenna along the major lobe axis at specified frequencies (2.15 dBi). They are intended to be used for antenna field pattern and gain measurements, or general RF sensing in the laboratory.
-
Product
High-Resolution Interferometer
10716A
-
The Keysight 10716A High Resolution Interferometer is used for single and multiple axis applications such as precision X-Y stages. The 10716A offers twice the resolution of conventional plane mirror interferometers and has the same excellent thermal stability as the 10706B High Stability Plane Mirror Interferometer. Measurement drift is typically of that exhibited by a conventional plane mirror interferometer. These features result in improved accuracy, repeatability, and thermal stability. However, slew rate is halved.
-
Product
Digital Gaussmeter
DGM-1D
-
DGM-1D: Digital Gaussmeter capable of measuring DC and AC magnetic field strength along one axis.
-
Product
VME System Electronics
-
Keysight VME electronics give the highest performance available in a laser interferometer system. Choose from a variety of axis and compensation boards.
-
Product
Omnidirectional Antennas
-
In radio communication, an omnidirectional antenna is a class of antenna which radiates equal radio power in all directions perpendicular to an axis (azimuthal directions), with power varying with angle to the axis (elevation angle), declining to zero on the axis.[1][2] When graphed in three dimensions (see graph) this radiation pattern is often described as doughnut-shaped. Note that this is different from an isotropic antenna, which radiates equal power in all directions, having a spherical radiation pattern. Omnidirectional antennas oriented vertically are widely used for nondirectional antennas on the surface of the Earth because they radiate equally in all horizontal directions, while the power radiated drops off with elevation angle so little radio energy is aimed into the sky or down toward the earth and wasted. Omnidirectional antennas are widely used for radio broadcasting antennas, and in mobile devices that use radio such as cell phones, FM radios, walkie-talkies, wireless computer networks, cordless phones, GPS, as well as for base stations that communicate with mobile radios, such as police and taxi dispatchers and aircraft communications.
-
Product
PXI/PXIe RF Matrix, Dual 2x2, 2.5GHz, 75Ω, SMB
42-837A-002
Matrix Switch Module
The 40-837A-002 (PXI) and 42-837A-002 are 75Ω 2x2 RF matrices with 2 banks in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-837A modules.
-
Product
Micrometers
-
In the hands of a skilled operator, the precision micrometer is the most accurate hand-held tool available. When close measurements are necessary, the micrometer is the ideal tool for the job because measurement and reading are on the same axis and the anvil end is supported by a strong frame.
-
Product
Inspection System
Pixie
-
3-D Metrology for automation. Pixie is a standard system for automated optical quality inspection. Pixie can be configured with 2 to 5 servo driven axis movement and the high-speed measurement capabilities make it suitable for inline and stand-alone solutions.
