Can bus
Controller Area Network
See Also: Serial, I2C, LIN, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus
-
Product
Diesel Fleet Maintenance Chassis Dynamometer
MD-7500
-
At the heart of the MD-7500 is a set of three air-cooled eddy current power absorbers. Each absorber, or brake, can hold up to 600-hp (total power of 1,800-hp) more than enough to simulate a fully loaded transit bus. As the systems PAU''s (brakes) are air-cooled, no water is required to or from the device eliminating the high cost of water consumption and/or the cost of an expensive water recovery system which can sometimes exceed the cost of the dynamometer system itself. Mustang is the only company that offers a Universal Fleet Test Bed without water supply requirements.
-
Product
Multi Protocol Boards
-
The EXC-4000 carrier board series was developed to meet the needs of avionic testers for multi-protocol integrated, digital bus testing. Modules may be selected out of a growing list which currently includes MIL-STD-1553/1760, MMSI, H009, ARINC-429, ARINC-708/453, Serial (232/422/485), Discrete and CAN bus. Additionally, an IRIG B decoder implements a global time stamp relative to the IRIG B pulses. The need for higher density, different protocols, and multi-channel on one integrated test card has made the EXC-4000 series very successful.
-
Product
Osprey / QXP Co-Processor
9740-Q
-
Quad+ speed Windows/NT Osprey Co-Processor for five times the system throughput, or more. Occupies one PCI slot. A writable control store, FPGA implementation of the PDP-11 architecture with 4 MBytes of tightly coupled, zero wait-state memory. Includes FPJ11® compatible hardware floating point. Performance equivalent 4.5 times the DCJ-11® and 130% of FPJ-11. On-card x86 microprocessor rapidly processes "virtual" I/O instructions. PCI bus speeds increase disk throughput by at least a factor of ten. Qbus®/Unibus® support logic for non-emulated devices is provided on-board with connector to wide bandwidth fibrechannel Qbus or Unibus adapter. Operates only under Windows/NT. WNT Support license included.
-
Product
OBD-II Breakout Box
PPECB
-
The Power Probe OBD-II Breakout Box is a CAN Bus circuit tester compatible with 12 and 24 Volt systems. The tool connects directly into the Vehicle’s Data Link Connector (DLC) testing for any abnormalities such as shorting and reverse polarity at the pins. If shorting or reverse polarity is present, connecting the PPECB first will prevent harm before connecting a Diagnostic Scan Tool. The Breakout Box provides a live display of present communicating signals without having to use a Digital Multimeter. Additionally, you can quickly test the voltages at all 16 pins.
-
Product
PCI Analog IO Board
MS 1803
-
*Bus Interface:- PCI Bus*Analog Inputs:- 16 Single Ended Inputs / 8 Differential Ended Inputs*Input Resolution:- 16 Bits*Input Range:- ±10V*Gain:- Programmable Gain Control (1, 2, 4, 8, 16)*Sampling Rate up to 100Ks/S*Peak Measurement +ve and -ve peak for all input channels
-
Product
PXI BRIC8 2Resource Distributor, 5Bus Matrix
40-569-125
Matrix Switch Module
The 40-569 PXI Matrix BRIC provides a range of high-density bus matrix inputs and resource distributor bussed configurations capable of switching up to 2A and up to 100VDC/70VAC. These large PXI matrix modules are available in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays.
-
Product
Remote I/O Systems
-
The clear assignment of a signal to a terminal while maintaining the existing instrumentation and wiring is a major advantage of remote I/O . A second is the significantly reduced wiring through the use of a bus interface to the control system - remote I/O offers the best of two technologies and is therefore ideally suited for modernizing and expanding process plants.
-
Product
PXI LIN Interface Module
Interface
The PXI LIN Interface Module is a bus interface for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LIN Description File (LDF) databases in integrated LIN databases. PXI LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
ccVPX Card
EXC-4500ccVPX/xx
-
Each channel using the M4K1553PxS (RT validated) module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The EXC-4500ccVPX/xx is supplied with C drivers (including source code), Merlin+ Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. Mating connector provided for I/O connection.
-
Product
Isolated Digital Input and Relay Output Card
104-IIRO-8
-
The 104-IIRO-8 is a low-cost card that provides isolated input and output for PC/104 Bus computer applications. The card has eight optically-isolated digital inputs for AC or DC control signals, eight TTL Inputs and eight electro-mechanical relay outputs. An Economy version can be ordered as Model 104-IIRO-8E which has no Change of State Detection or IRQs.
-
Product
Programmable Automation Controllers
-
Amplicon offers a broad range of programmable automation controllers (PACs) that can be deployed in a variety of industries. All support a broad range of automation and control protocols such as, Modbus TCP, Modbus RTU/ASCII, PROFIBUS, PROFINET, EtherNET/IP, EtherCAT and CAN bus. We have the technology capable of controlling simple edge processes through to complex automation applications across all industrial, infrastructure and building sectors.
-
Product
6U CompactPCI Enclosures & Systems
-
1~9U CompactPCI chassis for 6U CompactPCI boards , most of which are with front/rear panel I/O, H.110 CT bus and redundant power supplies.
-
Product
Eurocard Plugbord
E220-6U-1
-
VECTOR Electronics and Technology, Inc.
6U x 220mm Eurocard size for 96-pin DIN connectors. Pad-Per-Hole both sides. Voltage and ground buses around board perimeter on both sides. Pad and bus surfaces solder coated for user convenience.For solder, Wire-Wrap or mixed wiring methods. Row and column legends provided.
-
Product
NI-9861, 1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module
781962-01
CAN Interface
1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI‑9861 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The NI‑9861 is ideal for applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
Product
MIL-STD-1553 A / B Test And Simulation PCI Express Module
PCIe-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
12U (21") Insulated Bus Bar
BB-21-I
-
12U (21") insulated bus bar provides cabinets with recessed rail option and a convenient, isolated common grounding mechanism.
-
Product
Plugbord
4112
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side) on 0.156"(3.96mm) centers. 3-hole solder pads (0.28” x 0.080”) for interconnecting multiple component leads. Zig-Zag Bus Pattern on wiring side. Zig-Zag Bus Pattern provides access to voltage or ground at alternating hole positions. Continuous ground plane on component side with 0.085” etched clearance area around each hole Row and column legends provided
-
Product
Power And Bus Protection Units
-
Silver Engineering Inc. offers several Bus Protection Units designed to protect the power input to a spacecraft or payload during integration and test activates. The BPU’s monitor for over/under voltage and over current and disconnects power in the event of a fault condition.
-
Product
19" Rackmount Rugged, Fanless AIoT Platform for Real-time Video/Graphics Analytics
AVA-5600
Video Analytics Platform
- Intel® Core™ i7-7820EQ Processor and Mobile Intel® CM236 Chipset- NVIDIA Quadro® GPU MXM 3.1 Type A/B module on PCIe x164x M12 GbE with PoE, 4x USB 3.0- Rich Storage Options: 2.5" SATA 6.0 Gb/s drive bay, 1x M.2 2280 slot, 1x CFast socket- GNSS/3G/4G/WLAN support via 2x Mini PCIe slots and 2x USIM slots- MVB/CAN bus support by Mini PCIe add-on module (BOM option)- Nominal Voltage: 110VDC (EN50155 compliant)
-
Product
Signal Converters & Load Cell Signal Converter
-
Mantracourt provide a range of signal converter modules which take load cell or strain bridge inputs and provide a data output in a variety of bus and protocol formats. Hardware formats include RS232, RS422 RS485, CAN and USB. Signal converter protocols include Industry Standards such as MODBUS, or Mantracourt’s own proprietary protocols which have been optimised for either ease of use (MantraASCII2) or higher speed communications (MantraBus2).
-
Product
CPCI-Relay32
CPCI-Relay-32
Relay
CPCI Bus Interface 3.3 / 5 Volt PLX 9056 66MHz 32-bit, PCI r2.2compliant
-
Product
Digital Input/Output and Counter/Timer Card
PCI-DIO-96C3
-
This is a 96 line digital input/output card with counter/timer capabilities designed for use in high I/O density application requirements. I/O connections are made via four 50-pin header connectors. The card is 12.25 inches long (312 mm) and may be installed in any full-length 5V PCI-bus (or PCI-X bus) slot in X86 type PC’s.
-
Product
GPIB-RS232, Instrument Control Device - Taiwan 110VAC
779732-11
GPIB Controller
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
32-CH/64-CH Isolated Digital I/O PCI Express Card With Digital Filter
AX92351
-
The AX92351 is a 64-ch isolated digital I/O PCI Express card with 2,000VDC isolation protection. This high-density digital I/O card with high-speed PCI Express x1 bus is excellent for use in applications requiring digital control or monitoring, such as semiconductor machinery, PC-based industrial machinery, programmable I/O logic control, and process status monitoring. The AX92351 features 32 isolated digital input channels and 32 isolated digital output channels with isolation protection of 2,000V for industrial applications where high-voltage isolation is required. It is equipped with a board ID feature for easy identification of multiple cards in single system. There is a digital filter function to prevent input signals from carrying noise or a chattering. Each isolated input has a sink or source current which supports dry and wet contact for maximum application flexibility. The card has a wide range of input voltage from 10 to 30V to meet most industrial application needs. The AX92351 also provides two interrupt sources on digital input channels. Digital output has open controller and supports maximum 30VDC. The read-back function is another useful function that allows monitoring each output port.
-
Product
1-Channel 3.6 GHz or 2-Channel 1.8 GHz 12-bit A/D with Virtex-6 FPGA - XMC
Model 71640
-
- View product video- Ideal radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- One-channel mode with 3.6 GHz, 12-bit A/D- Two-channel mode with 1.8 GHz, 12-bit A/Ds- 2 GB of DDR3 SDRAM- Sync bus for multimodule synchronization- PCI Express Gen. 2 interface x8 wide- Optional user configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Clock up to four modules with Model 7194 High-Speed Clock Generator - PMC/XMC- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Open Test Platform for High Performance Automotive Applications
TSVP
Test Platform
The R&S®TSVP family of products is an open test platform from Rohde & Schwarz ideal for high performance automated test equipment (ATE) applications. The chassis contains a mechanical frame, digital backplane, analog backplane, mains switching and filtering, power supply and diagnostic extensions. A highlight is the analog bus for routing measurement signals between different slots without additional external wiring.
-
Product
Fibre Channel XMC Interface Module
XMC-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Supports DMA for high speed streaming of data to/from the board - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
1553 Bus Cables, Couplers, Terminators, and Kits
Terminator
Please review 1553 Bus Accessories to the right. You can also use the Login-Download link above (login required) to access all the Hardware Manuals with specific cable and connector information. Most 1553 Cards and ENET devices have optional 1553 Jack and AUX I/O DB cable assemblies. Please see the respective product pages part numbers tab. Most ARINC products include flying-lead cable assemblies.Please use the Contact link to email/phone sales for a login as needed.
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
42-203-001
Fault Insertion Unit
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
Product
Open Frame 3U 34HP Chassis
-
An open-frame solution for the open-minded engineer. With moveable rear profiles (up to 2.5mm,) 3U and 6U backplane compatibility options, air or conduction cooling options and the ease of fast and simple backplane interchangeability for fluid transition between VITA and PICMG bus architectures, the Hartmann Open Frame Chassis solution is the tool for customers who need versatility, accessibility and longevity.
