-
product
EMC Testing
D.L.S. Electronic Systems, Inc
EMC testing and consulting services to the Electronics, Medical Equipment, Automotive, Aerospace, Computer, Telecommunications, and other industries. We are a NVLAP certified test facility, capable of testing electronic equipment to today's high frequency requirements. Our 14 Test chambers and 3 Open Area Test Sites can perform full scan Immunity and Emission testing at frequencies up to 40 GHz. Please contact us for your specific requirements.
-
product
PXI Automotive Switch Simulator Modules
Pickering's Switch Simulator Modules are designed for automotive test applications. These modules simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. They allow automotive I/O devices to be tested for correct operation under adverse conditions.
-
product
AC Line Splitter
1937
Peaceful Thriving Enterprise Co Ltd
The AC line splitter is a helpful testing device for electrician. Electrician can measure the current with clamp meter through the X1 and X10 measuring rings. X1 is 1:1 measurement, and X10 is ten times (1:10) of the actual current, which is helpful for small current measurement. This device also combines the function of socket tester and GFCI tester, which means electrician can use this tester to test socket and load at the same time.
-
-
product
Solder Paste Analysis
SPA1000
The SPA 1000 also introduces new process control capability by accurately measuring the suitability of the solder paste prior to its implementation on the production line. It achieves this by determining the "Open-Time" for the paste. It also performs the Slump Test and both of these methods provide a "Go/No Go" answer in less than 30 minutes to ensure minimum delay for the production line.
-
product
HDMI Assembled Test Connector
HDMI Testplug with plug (1000 mm cable), HDMI Testplug with female socket (1000 mm cable), HDMI Testplug with 19-pin connection board. Applications in video and audio systems.
-
product
Emergency Battery Test Fixture
TA-60
This test fixture will allow servicing of the 60-1321-( ) series of emergency exit light power supply. These supplies are used in many aircraft to annunciate exit lighting when aircraft power failure occurs. The TA-60 test fixture is equivalent to the suggested test fixture in the OEM 60-1321 CMM. The four load lamps are conveniently placed behind an acrylic red lens for proper viewing while performing load test. The bench cable is provided as part of the test fixture.
-
product
International Marine Organization
GMDSS Tester MRTS-7
The International Marine Organization (IMO) orders all GMDSS equipment to pass regular maintenance and to confirm that it meets all the appropriate performance requirements. In case of test failure ships can be detained in Port.
-
product
Microelectronics Test & Engineering Services
EAG's Microelectronics Test and Engineering lab network provides semiconductor and electronics design firms worldwide with test, debug, and early engineering support to help you with new product introduction. We actively service a broad range of semiconductor and electronics companies worldwide. Services include ATE testing, Reliability testing and qualification, ESD testing, Failure Analysis, FIB Circuit Edit and Debug. for both ICs and systems
-
product
Mechanical Testing
The Mechanical Testing Department at IMR is well equipped to perform most standard mechanical testing, as well as specialized tests designed to the customer's requirements. A complete in-house machine shop supports the department with precise specimen preparation and fixture fabrication.
-
product
Vibration Monitoring
Vibration tests must be safe and reliable and this is especially true for high value specimens in critical aerospace testing applications. Here, m+p Coda offers maximum safety: The monitoring system captures and records data such as acceleration, temperature and strain continuously during vibration tests - irrespective of the vibration control system in use. Each channel can be configured separately for total flexibility.
-
product
Highly Accelerated Life (HALT) Test
HALT consists of high and low temperature and 3 axis vibration testing performed either individually or in combination.Highly accelerated life testing is performed to identify design weaknesses and problems prior to production. HALT subjects equipment to overstress conditions at a level which does affect life, but offers an advantage by reducing the design and development phases of a program.
-
product
Retractable Cable With Magnet Adsorption
3701
Peaceful Thriving Enterprise Co Ltd
*2 x 6m retractable test leads.*Used as an extension cord for cars, trailers, boats and more.*Optional accessory included alligator clips, test probes and banana plugs.*The tester can be used with any multi meter or device equipped with banana jack connectors.*Embedd A Magnet on the back to fix on suitable metal sheet of cars easily.
-
product
IP Code Test Equipment
Weice Testing Instrument Co.,Ltd.
IP Code, International Protection Marking, sometimes interpreted as Ingress Protection Marking, classifies and rates the degree of protection provided against intrusion (body parts such as hands and fingers), dust, accidental contact, and water by mechanical casings and electrical enclosures.
-
product
NI-9229, ±60 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Module
779785-01
±60 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Module - The NI‑9229 performs differential analog input. The NI‑9229 is an effective general-purpose analog module because of its resolution, sample rate, and input range. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating.
-
product
BNC (F) To Alligator Test Clips
3788
Minigrabber? test clip hooks attach to terminal sizes up to .060? diameter. Converts BNC (Male) cables to Minigrabber test clips for test versatility.
-
product
Optics Test Systems
Scientific Instrument Engineering
Optik Elektronik Gerätetechnik GmbH
Development, design, manufacture and assembly of opto-mechanical assemblies and complete devices, including software.
-
product
Shielded Test Cell
With an operating frequency starting at 10kHz, the Standard Test Cell (STC) creates an ideal environment for testing wireless devices for such technologies as GSM, UMTS, CDMA, Bluetooth, DECT, etc. Developed for the R&D, production and quality control environments where space is critical.
-
product
Energy Meter Test Bench
Bofa Instrument & Equipment Co., Ltd
Ideal instruments to test all kinds of energy meters accurately.
-
product
Low PIM Coaxial Switch, DC to 20 GHz, Matrix
87406Q
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87406Q is a low PIM matrix coaxial switch, operating from DC to 20 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency and ultimately maximizes test throughput.
-
product
Test Finger Probe
Shenzhen Bonad Instrument Co., Ltd.
BONAD’s test fingers, test probes and test needles comply with IEC 60065, IEC 60238, IEC 60335, IEC 60529 and IEC 61032 standards and are essential instruments for the protection against electric shock of household and similar electrical appliances. For more information, please contact us and BONAD will provide you with professional technical advice and high-quality testing equipment.
-
product
JTAG/Background Debug Mode Test System PXI Card
NX5300
The NX5300 is a single slot 3U PXI device and interfaces to the unit under test via an On-Chip Debug (OCD) or JTAG port. The NX5300 is a high performance JTAG based background debug mode (BDM) diagnostic system designed for functional test, development, programming and troubleshooting of microprocessor and microcontroller based embedded processor systems.
-
product
Solid Dielectric Test Cell
• 3 terminal design • 70pF at 1mm gap nominal capacitance • Max test voltage of 2.5kV AC or DC • Suitable for use with Eltel models DTR-3K, ADTR-2K Plus Test Sets
-
product
Acceleration Simulation Mode (ASM) Roller Set
ASM-P-PLUS | VP 230047
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-P-PLUS roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The increased tractive force of its eddy current brake means that the ASM-P-PLUS is also suitable for power measurements at constant speed and constant tractive force.
-
product
Rugged VPX Power Supplies
The NAI VPX family of power products include a variety of standard features, including continuous Background Built-In-Test (BIT); remote error sensing; and protection against transients, overvoltage, overcurrent, short circuits and over temperature. These intelligent designs also have the flexibility to address special needs. Optional current share is available on main outputs.
-
product
Cable/hamess Tester
LX-560B
Shenzhen Lian Xin Technology Co., Ltd.
Cable/Harness Tester (low-pressure type) features its capability of testing the components inside the wire, the test speed more than double faster than that of the traditional wire testers, and the provision of such functions as unilateral, turn-on resistance editing, and spot metering color editing.
-
product
Oxygen Sensor Tester And Simulator
7650
Peaceful Thriving Enterprise Co Ltd
This device is designed to test and to simulate 1V Zirconia and 1V/5V Titania type oxygen sensors. The simulation can help user to exam the function of the ECU. Moreover, it can analyze the type of connection wire.
-
product
LX-D Shore D Rubber Durometer, Hardness Tester
LX-D
Shenzhen Chuangxin Instruments Co., Ltd.
LX-D durometer is suitable for hardness test of high degree of hardness material, such as common hard rubber, hardened resin, glass, acryl, Plexiglas, thermos plastic rubber, printing plate, fibre, acryl,etc. The product conforms to GB/T531-1999 and other related standard request.
-
product
Handset One Box Testers
Anritsu's handset one box testers offers multi-system service test platforms. These are high-speed measurement solutions used in production testing and design proving.
-
product
Hign Speed Bare Board Test System By Non-Contact Test Technologies
SX-750SUPERⅣ
Suitable for a wide range of applications. Can be connected to a wide range of machines: from hand press to reel mechanism and in-line mechanism. We offer docking with our customers own machines. Compact main tester simplifies integration via installation inside a mechanism. If requested, we will perform a study to decide which functions should be added.
