Chip
Passive or active components test and their interconnected circuitry in silicon or germanium.
See Also: Integrated Circuit, IC
-
Product
Integrated Potentiostat and Multiplexer
EmStatMUX8
-
Based upon the EmStat range, there are two types of multiplexers to suit most types of sensor array work. The MUX8 is the most flexible offering the ability to connect arrays made of up to eight working electrodes in two or three electrode cell types and chips sharing a reference electrode and/or counter electrode. The MUX16 is suitable for sensor arrays or chips with sixteen working electrodes all sharing a RE and/or a CE. Both instruments are suitable for laminated layer corrosion analysis.The potentiostat is controlled and powered by USB and is used with PSTrace allowing for simultaneous sampling of each channel at a rate of 25 ms/channel. Standard packaging includes a shielded cable with connections for a working, a counter and a reference electrode by means of 2 mm banana connectors and mini-crocodile clips, a stripped end, Dsub-37 terminated flat cable and a USB cable. To make connections to chips simpler the Connection Terminal is an optional extra providing clearly marked screw terminals to the electrodes and can be directly joined to the ESMUX via their D-Sub connectors.
-
Product
AMC GBit link card/VITA 57 FMC carrier
SIS8100
-
The SIS8100 will be a single width mid height AdancedMC card. It will interface with a single PCI Express lane over a PLX Technology PEX811 PCI Express to local bus bridge chip and have an on board Virtex IV FPGA. The default stuffing option has a Small Form Factor (SFF) optical link medium that can be operated at 1, 2.5 and 4 GBit/s.
-
Product
DDR3 SODIMM
SQR-HS3I
-
Original Samsung/Micron IC chips adapted, Heatsink attached. Data transfer rate: 1600 MT/s, Operating temperature: -40 °C ~ 85 °C, 3years longevity, Fixed BOM, Lifetime warranty.
-
Product
High Soeed CMOS System on Chip (SoC) Line Scan Image Sensor
LS4k
-
The LS4k is a high speed CMOS System on Chip (SoC) line scan image sensor optimized for applications requiring short exposure times and high accuracy line rates. It incorporates on chip two pixel arrays consisting of 2 rows with 4,096 7µm pitch pixels and 4 rows with 2,048 14µm pitch pixels respectively, a high accuracy (12-bit) high speed (84MHz) analog-to-digital conversion (ADC), and sophisticated on chip optical calibration for PRNU, DSNU, and lens shading correction.
-
Product
Read-Write Analyzers
-
Guzik Read/Write Analyzers (RWA) work in conjunction with Spinstands to write data to the disk media and read back the signal for detailed analysis. We have two RWA-4000 series available for For Two Dimensional Magnetic Recording (TDMR) and non-TDMR technologies. The RWA 4000 series offer upto 8Gbit/sec maximum write data rate and 3.5 GHz analog bandwidth for all parametric measurements. Each RWA features a pattern generator with 1psec resolution of bit pre-compensation and supports PRML chip integration. Servo writing and processing is provided for Guzik Spinstand models. Select the pre-amplifier (UP14) as well as a variety of enhancements including programmable filters and PRML chip adapters.
-
Product
Fast Temperature Shift
CherryTemp
-
CherryTemp is a temperature controller based on two independent Peltier channels, allowing for very accurate temperature control and ultra-fast shifts from 5°C to 45°C. A thermalization liquid circulates from a reservoir to the heat exchangers (heating/cooling Peltier elements) where it is thermalized to a target temperature. Once thermalized, this liquid can be quickly injected to a microfluidic device (CherryTemp chip) mounted near the sample. Because of the small thermal mass (the distance between the microfluidic chip and the sample), the temperature transfer is very fast (less than 10 seconds) and of unprecedented accuracy due to a feedback loop control of the room temperature and the heat-sink played by immersion objective lenses.
-
Product
Isolation Amplifiers
-
Isolation Amplifiers provide power supply designers with a higher performing, single chip alternative to isolation techniques based on optocouplers and shunt regulators. Analog Devices ADuM3190 and ADuM4190 isolated error amplifiers have a 400 kHz bandwidth, with 0.5% typical initial accuracy at 25°C and 1% total accuracy over the extended temperature range of –40˚C to +125˚C. This provides manufacturers of ac-to-dc and dc-to-dc power supplies with a significant upgrade in speed and operating temperature range, as well as a 5× improvement in transient response.
-
Product
FPGA Card
VP869
-
The VP869 is a high-performance 6U OpenVPX FPGA processing board featuring two Xilinx® UltraScale+™ FPGAs and a Zynq® 7000 Series multiprocessor system-on-chip (MPSoC). It is designed for the most demanding mission critical military, defense, and industrial applications where extreme FPGA processing and I/O bandwidth capabilities are needed. Applications include electronic warfare, signal intelligence, radar/sonar, and high performance embedded computing.
-
Product
8GB SO-DDR5-5600 1GX16 1.1V SAM
AQD-SD5V8GN56-SC
Memory Module
SAM Original Chip, PCB: 30μ gold finger, Anti-sulfuration, On-die ECC for Enhanced RAS, Operating Temperature: 0°C ~ 85°C.
-
Product
Emulation Platform
Veloce
-
The Veloce® Emulation Platform dramatically reduces risk in the verification of today’s complex SoCs and is a core technology in the Mentor Enterprise Verification Platform™ (EVP). Mentor’s software and application solutions and continual enhancements enable a comprehensive verification environment for IP, chip, and system level verification.
-
Product
Chip Test Adapter
RAMCHECK Sync
-
The RAMCHECK Sync Chip Adapter tests popular TSOP SDRAM memory chips in sizes of 16Mx16, 4Mx16, 32Mx8, 8Mx8, 64Mx4, 16Mx4 and more. Picture above shows the adapter with all optional sockets for 54, 50 and 44-pin.
-
Product
Capacitors - High Q MNOS Series
-
Macom Technology Solutions Holdings Inc.
MACOM’s MMI-9000 and 9100 Series Chip Capacitors feature high stand-off voltage and low dielectric loss due to our use of nitride/oxide dielectric layers. Gold bonding surfaces, top and bottom provide ease of bonding and minimum contact resistance. MACOMs high Q MNOS series of capacitors have high insulation resistance, low dissipation factor, and low temperature coefficient, which are features that produce devices with excellent long term stability.
-
Product
WLCSP Probe Heads
-
Smiths Interconnect offers Wafer Level Chip Scale Package (WLCSP) Probe Heads utilizing spring probe technology which provide high parallelism in test, superior signal integrity and high speed / RF testing capability.
-
Product
Chip Obsolescence Solutions
-
Solve component obsolescence problems with an Ironwood adapter and an alternate device. Adapters convert the pinout of an alternate device to maintain compatibility with an existing footprint – no need to redesign a new circuit board. Very often, these adapters (called Package Converters) are a simple 1:1 pin mapping from the new package to the old. Here are a few examples of package converters and how they can solve chip obsolescence issues.
-
Product
Step Recovery Diodes
-
Macom Technology Solutions Holdings Inc.
MACOM’s Silicon and GaAs varactor multiplier diodes provide broadband performance ranging from 10 MHz to 70 GHz. They are ideal for multiplier circuits and are available in die form, plastic and ceramic packaging. These diodes boast a flip chip series for higher frequency millimeter wave applications; plastic packaged series for microwave frequency surface mount applications; ceramic packaged series for high power waveguide and coaxial applications.
-
Product
Cryogenic Temperature Sensors
Cernox®
-
Cernox® thin film resistance cryogenic temperature sensors offer significant advantages over comparable bulk or thick film resistance sensors. The smaller package size of these thin film sensors makes them useful in a broader range of experimental mounting schemes, and they are also available in chip form. They are easily mounted in packages designed for excellent heat transfer, yielding a characteristic thermal response time much faster than possible, with bulk devices requiring strain-free mounting. Additionally, Cernox sensors have been proven very stable over repeated thermal cycling and under extended exposure to ionizing radiation.
-
Product
Automated Programmer Superpro Sb05
-
※ Four Pick & Place nozzles, Eight socket pressing actuators and 2 tape feeders※ High throughput up to 2400UPH※ Embeded with eight ultra-high speed programmers SuperPro / 7500, each with up to 4 sockets, totally 32 sockets. Throughput 60 times higher than SuperPro / SB01 for eMMC devices※ Supports over 80,000 devices from over 300 IC manufacturers※ Supports tray, tape and tube input and output. Supports laser and ink marking※ Short change-over time※ Intelligent s/w cuts learning curve and setup time, makes task management an easy job※ Compact sizeHigh throughput：4 nozzles, 8 independent socket pressing actuators and 2 tape feeders. Up to 2400 UPH for devices with programming time less than 50 sec. Throughput 0.6 to 60 times higher than SuperPro/SB01, especially higher for large capacity devices like eMMC, NAND /NOR FLASH,SPI FLASH. Suitable for both small and large capacity devices. Prog. Time (S) 50 60 120 180 240 300 UPH (unit per hours) 1600 1600 840 560 420 336 Accurate positioning：Equipped with high performance servo system, precise CCD cameras and vision algorithm for device alignment and sockets / pick & place spots positioning.High performance programmers： 8 ultra-high speed universal gang programmers SuperPro/7500 resident. Each with up to 4 sockets, totally up to 32 sockets in the system. Supports up to 100,000 devices from over 300 IC manufacturers and growing.Varied I/O devices：Supports tray, tape and tube input and output. Supports laser and ink marking. Supports packing conversion and can work as a packing conversion machine alone.Short change-over time：I/O devices and socket adaptor are easy to be changed when programming task need to be changed. Socket positioning can be performed automatically. Projects can be loaded automatically with barcode scanning.Powerful and intelligent software：Setup data saved for next operation, log file and statistic reports for quality and yield traceability, flexible sockets prohibition strategy promises high yield rate for unattended operation, graphical user interface cuts learning curve, prevents chip over-lapping by socket checking before chip placing.Remote Control：Remote project loading, quality monitoring, volume control, file security.
-
Product
Photonic Device Testing
-
ficonTEC’s series of photonic device testing machines is focused on automated electrical, optical or mixed-signal electro-optical characterization (test-&-qualify) of chips and dies, opto-electronic assembles and integrated devices. Capability includes PIC design validation and device verification.
-
Product
PCI Evaluation Board
BCM91250E
-
The BCM91250E is a full-length PCI evaluation board with the SiByte® BCM1250 dual-processor System on a Chip. The board is designed for software development and for developing PCI applications that require high-performance processors.
-
Product
Pyroelectric Detectors
-
Pyroelectric detectors are thermal detectors; i.e. they create an electric signal due to temperature changes in the chip. This temperature change is caused by absorption of light. We do use LiTaO3 and DLaTGS as pyroelectric materials. Basically such detectors cover the whole spectra. However, they are mainly used for mid-wave and long-wave infrared detection (MWIR and LWIR). In addition, the usage in the THz region seems to become more popular these days.
-
Product
Semiconductor Test Equipment
-
Wewon Environmental Chambers Co, Ltd.
Probe card manufacturing need the semiconductor test equipment. When we designed the thermal testing equipment, Only some commonly used test items are packaged into the IC tester, and the logic function of the verification chip is implemented in a fixed test mode. But as chip products diversify, Some thermal inducing system can no longer do it alonehttps://www.wewontech.com/semiconductor-test-equipment/
-
Product
Extreme Rugged PC/104-Plus Single Board Computer with Intel® Atom™ Processor System-on-Chip
CM2-BT2
Single Board Computer
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
Product
64 Channel Multihit TDC
VX1190B-2eSST
-
The VX1190B-2eSST is a 64 channel Multihit TDC, housed in a 1-unit wide VME64X 6U module. The unit features High Performance Time to Digital Converter chips developed by CERN. LSB can be set at 100 ps (19 bit resolution, 52 µs FSR), 200 ps (19 bit, 104 µs FSR) or 800 ps (17 bit, 104 µs FSR).
-
Product
Data Acquisition & Control
-
Blue Chip Technology have been designing and manufacturing data acquisition and control boards since 1986. The current range of boards have digital and analog IO and an excellent record for reliability in the harshest of environments.
-
Product
PCIe 4.0 RAID Controller
MegaRAID 9560-16i
-
The MegaRAID 9500 series is the industry’s first PCIe Gen 4.0 RAID adapter family, offering PCIe Gen 4.0 host and storage interfaces. The MegaRAID 9560-16i adapter, based on the SAS3916 high-port count PCIe 4.0 x8 RAID-on-Chip (RoC), delivers twice the performance of previous generations.
-
Product
Caibration Equipment For Lab Use
-
In the field of high-power semiconductor testing, PONOVO has launched a smart test platform with high-speed high-frequency, high-voltage, high-current power sources, combined with high-speed, high-precision high-voltage, high-current analog acquisition technology and high-speed digital processing control system. The platform can complete the testing of dynamic parameter parameters, static parameters, thermal parameters and mechanical parameters, and power life parameter of various types of high-power semiconductor devices, modules, and chips, which could meet different testing requirements. It is the universal testing platform for automated testing for different application purpose, such as the research and development testing, engineering acceptance test, factory acceptance test, etc.
-
Product
Smart Lighting
-
The AS721x/AS722x are complete System-on-Chip (SoC) sensor-integrated IoT smart lighting managers for color-tunable white lighting applications. They also support daylight harvesting and color/lumen maintenance lighting applications. 0-10V control and network-enabled high-level command inputs are combined with industry-standard PWM and 0-10V outputs for direct control of LED power systems.
-
Product
Extreme Rugged PC/104 Single Board Computer with Intel® Atom™ Processor System-on-Chip
CM1-BT1
Single Board Computer
The CMx-BTx is a PC/104-based, Single Board Computer (SBC), fully compliant with the PCI-104 Specification, Version 1.1 and partially compliant with the PC/104 Specification, Version 2.6. PC/104 SBCs are very compact and highly integrated computers. This SBC features the 22nm, Intel® Bay Trail SoC. The board provides a DDR3L SO-DIMM socket, a PC/104 connector, a PCI-104 connector, two USB 2.0 ports, one USB 3.0 port, up to two Gigabit Ethernet ports, up to two SATA 3 Gb/s ports, one dedicated HD-Audio panel connector, one VGA port, one LVDS port, up to four COM ports, one mini-PCIe slot (with one USB 2.0 port included). The CMx-BTx can be run with only 5 volts and is capable of running operating systems like DOS, Windows XP/7/8 in either 32-bit or 64-bit configuration, Linux, VxWorks, and others. Another feature included on the board is a fail safe BIOS that enables the user to start the module even if the original BIOS is corrupted.
-
Product
Hot Electron Bolometer (HEB) Mixers/ Receivers In Terahertz Range
-
Insight Product Company offers Hot Electron Bolometer (HEB) mixers, receivers, and chips made from NbN or NbTiN thin film. The HEB mixers can operate at frequencies of up to several terahertz.
-
Product
16G DDR5-5600 2GX8 1.1V SAM -20~85℃
AQD-D5V16GN56-SBH
Memory Module
SAM Original Chip, Industrial Design for Improved Reliability, PCB: 30μ gold finger, Anti-sulfuration, Semi Wide-temp Support -20~85℃.
