Showing results: 76 - 90 of 6622 items found.
-
DARE Electronics
DC voltage sensors monitor input voltages ranging from 3 to 500 volts DC with a trip point accuracy of up to 1% in airborne, military and ground power applications. Using internal electronic circuits to detect, monitor and/or sense DC voltage, DARE DC voltage sensors, monitors, and voltage sensing relays can open or close a circuit when a certain pre-set over or under voltage condition exists or the DC voltage falls outside the specified voltage band window.
-
VIS -
MeterTest Ltd.
The VIS voltage integrated source was designed to be used as a stable alternating voltage source for electricity meter test equipment, and in laboratories. The output voltage is isolated and independent of mains voltage. VIS is available in a variety of configurations depending on the values of output power and output voltage.
-
Shanghai Sanki Electronic Industries Co., Ltd.
Impulse voltage generator Impulse voltage generator is mainly used for test products such as power equipment to perform lightning impulse voltage full wave, lightning impulse voltage chopping, operating impulse voltage wave and steep wave impulse voltage test, to inspect insulation performance. The technical indicators comply with national standards and IEC standards.
-
Greenlee Tools
*Verify the presence of voltage without contacting the conductor*Audible and visual alert when voltage is present*Powered by a rechargeable Li-Ion battery*HI/LO proximity voltage detector with two voltage ranges, 50V-4kV and above 4kV
-
2672AM -
Shenzhen Chuangxin Instruments Co., Ltd.
Withstand Voltage Tester is used to measure the dielectric (withstand voltage) strength, which can be intuitive, accurate and fast tested the electrical safety performance indicators of the object, such as the breakdown voltage, leakage current etc. And Withstand Voltage Tester can be used as a high voltage source to test performance of the components and whole machine.
-
-
SIM928 -
Stanford Research Systems, Inc.
The SIM928 Isolated Voltage Source is ideal for applications where ultra-clean DC voltage is required. Voltage can be set between ±20 VDC with millivolt resolution, and the source can drive up to ±10 mA
-
VDL1000 -
Supco
Use this non-contact voltage tester to detect voltage in cables, cords, circuit breakers, lighting fixtures, switches, outlets, and wires. A bright red LED will tell you the tester is seeing voltage.
-
NCVT-3 -
Klein Tools, Inc.
Provides non-contact detection of AC voltage.Detects 12 – 1000V AC with simultaneous visual and audible voltage indicators.Bright flashlight illuminates work area and may be used independent of voltage detection function.Visual LED bar graph indicates the presence of voltage – the higher the voltage sensed, or the closer to the voltage source, the more LEDs light up.Bar graph visual voltage indicator utilizes up to five vibrant LEDs for easy interpretation/viewing.Audible voltage indicator beeps at a greater frequency the higher the voltage that is sensed, or the closer to the voltage source.“Auto Power-Off” conserves and extends battery life.Screw-thread battery cap with O-ring ensures protection against dust and water ingress.Lightweight, compact tool with pocket clip provides convenient storage and quick access.IP67: Dustproof and waterproof.6.6 feet / 2 meter drop protection.CAT IV safety rating for 1000V.Conforms to CE requirements.
-
SSG 3000 -
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR SSG 3000. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* high surge energy in each voltage range
-
CZ20074 -
Aegis Pty. Ltd.
The Aegis adjustable sensitivity AC Voltage Detector is the only tool you need to test AC voltage. About the size of a marking pen, this battery operated, non-contact tester detects AC voltages from 50 - 1000V. It's easy to operate, with flashing LED indicators, an audible buzzer and vibration to alert the user when the AC voltage has been detected. The unit will glow green when safe, and when voltage is detected it will flash red and beep at an increasing rate as you get closer to the voltage source.
-
ISL21010 -
Renesas Electronics Corp.
The ISL21010 is a precision, low dropout micropower bandgap voltage reference in a space-saving SOT-23 package. It operates from a single 2.2V to 5.5V supply (minimum voltage is dependent on voltage option) and provides a ±0.2% accurate reference. The ISL21010 provides up to 25mA output current sourcing with low 150mV dropout voltage.
-
LVD-17 -
Standard Electric Works Co., Ltd
● Microprocessor-controlled smart voltage detector.● Bright LED and audible alarm sound when voltage is present.● Designed for non-contact voltage detection.● Sensitivity adjustable with thumbwheel.● Adjustable for use on power wiring plus lighting, thermostats and other low voltage circuits.● LED indication for battery condition.● Identify Hot and Neutral.
-
ESDEMC Technology LLC
High Voltage Pulse Attenuator is used to attenuate high voltage pulse signals in a 50 system. It is consist of highly surge robust components with great voltage linearity. The device is symmetrical, Input and output can be exchanged.
-
BVS -
IBEKO Power AB
DV Power battery voltage supervisor – BVS, is an accurate battery voltage monitoring system that monitors the state of health of battery systems. It records important battery parameters such as battery voltage, inter-cell connection voltage, and ambient temperature. Because of that, it can be a support tool for capacity testing.The BVS voltage supervisor is an integrated system consisting of:BVS Control Unit (BVS-CU)Cell Voltage Modules (CVM)String Voltage Module (SVM) (optional)String Current Module (SCM) (optional)It is an ideal testing tool for maintenance, troubleshooting and performance tests on individual stationary batteries and battery packs in critical backup energy solutions.BVS-CU provides ambient temperature measurements on multiple locations (4 temperature channels). Overall string voltage and string current monitoring can be achieved by using an optional string voltage module (SVM) and string current module (SCM).There are two types of DV Power battery voltage supervisors:BVS – One cell voltage module measures 1 cellBVS-4 – One cell voltage module measures 4 cellsCVM modules detect cells that fail a discharge test based on monitored voltage values. As a result of that, these cells can be safely removed from the battery string.Data acquisition and analysis of data collected from the modules are available in the DV-B Win application software suite. They provide data viewing, tracking, and generation of comprehensive reports.