Voltage
The tension of an electromotive force.
-
product
Voltage Controlled Phase Shifters To 3200 MHz
Pulsar's Voltage Controlled Phase shifters utilize a DC voltage to control the phase of the RF signal applied. These phase shifters utilize varactor diodes to produce the necessary phase requirements. Phase of the 180 and 360 degree designs are available, and phase can be controlled with a DC voltage 0-20 Vdc. Modulation of these phase shifters is typically 100 kHz, and maximum input power is +5 dBm.A wide variety of package styles are available, such as plug-in, flatpack, TO-cans, and connectorized housings, though the most popular are the miniature surface mount packages. Surface mount packages are available on tape and reel, for automated assembly techniques.
-
product
Handheld Digital Multimeter, AC/DC Voltage, Continuity, Diode, 3.5, 2000, Manual, 250 V
72-13440
*Palm size digital multimeter with 2000 count clear LCD display*CAT II 250V environment safety rating*Manual functional select and manual range selection*2m drop test, precision protection*Auto backlight off*Knobs shift smoothly, in-line with ergonomics*Equipped with comfortable protective cover and test probe holder*Powered by AAA 1.5V x 2 batteries*Non-contact voltage (NCV) detection*12-month limited warranty *view Terms & Conditions for details
-
product
sbRIO-9223, Non-Enclosed, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
785480-01
Non-Enclosed, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO-9223 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The sbRIO-92233 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the sbRIO-9223: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
product
High Voltage Pulse Attenuators
Barth High Voltage Pulse Attenuators are matched impedance coaxial attenuators for use primarily in pulsed 50 ohm systems, or where occasional transients would damage ordinary units. The attenuator design closely matches the impedance around each resistor, to that resistor. These attenuators feature an input impedance very close to 50 ohms, with characteristics as good or better than most microwave attenuators. These units are ideal for use in nuclear and high energy experiments. Extensive testing during manufacturing insures very high reliability for single-shot experiments. A voltage coefficient of the resistive film of less than .0001 %/V allows low voltage calibration of most systems.
-
product
Electronic AC/DC Voltage Tester
ET60
The ET60 voltage tester requires no batteries as it measures AC/DC voltage up to 600V in electrical circuits, outlets, light fixtures and anywhere else AC/DC voltage testing is required.
-
product
High Voltage Holiday Detector
AP-W
The Model AP/W can be customized for many applications, including In-Plant operations. Power from 115v or 230v AC Connection for external klaxon Custom cables for automated systems We can customize the AP/W to fit your needs. Contact us for details!
-
product
High-Voltage Isolation Amplifier
Knick Elektronische Messgeräte GmbH & Co. KG.
Measurement of DC or AC voltages up to () 3600 V and of large DC currents to about () 20 kA with shunt resistor or directly in the device to () 5A DC and AC. Variants with calibrated range selection.
-
product
AC / DC Voltage And DC Polarity Tester
1861
Peaceful Thriving Enterprise Co Ltd
*With cETL Approval.*Built-in LED and neon lamp indicator.*Neon lamp for 120V-230V-400V AC.*LED Display for 12V-50V and polarity.*Long lead connects tester body and probe.
-
product
AC / DC Sensors For High Voltage Measurements
The Mors Smitt CatEnergy sensor range provide a proven, reliable, accurate and cost-effective solution for rolling stock. Based on its capacity of multi-voltage and current measurements, alone Mors Smitt sensor products could be used as single solution for all function requiring high voltage measurement on existing and new build train.
-
product
High Voltage Oil Test Set
Supreme Instrument Laboratories
Supreme High voltage Oil Testing Apparatus is designed for testing of dielectric strength of transformer Oil or any other insulating liquids. It constitutes a complete equipment and apart of an A.C. supply of 230 / 240 Volts, no other supplementary facilities are required for its operation.
-
product
Voltage Input0 to 2.5/10/25V
TGPR-0704
Voltage input data logger that is housed in a robust, waterproof (IP68) rated case.The TGPR-0704 can be used to record the output from a number of industry standard sensors. Common applications include pressure and windspeed monitoring.
-
product
PXI/PXIe High Voltage Programmable Resistor Module, D-Type Connector
40-230-113-HI
The 40-230-113-HI (PXI) and 42-230-113-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 239Ω with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
product
Standard Voltage 50 Pin D-Type Connectors
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
Non-Contact Voltage Detector
273 HP
Standard Electric Works Co., Ltd
2 ranges for selection : LOW 50V~1.5kV, HIGH 1.5kV~132kV. There is no power consumption in off mode : 0uA. Nice mechanical slide switch for function selection : HIGH / OFF / LOW. The power consumption in low voltage detection mode : Less than 20mA. The power consumption in high voltage detection mode : Less than 20mA. Bright LED and audible alarm sound when voltage is present. Lightweight, robust and compact. Efficient and easy to use. Users have to use the Hot Stick when test high voltages between 1.5kV~132kV. SEW provides nice optional accessories of Hot Sticks HS-175 and HS-120 for high voltage detection. Optional accessories : HS-175 Telescopic hot stick (triangle-type) and HS-120 Hot stick.
-
product
Single Channel High Voltage Linear Amplifier
A800
The A800 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of ±400V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±4 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
product
High Voltage 9 Pin D-Type Cables - Connector to Connector
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
AC-DC High Voltage Power Supplies
These modular High Voltage supplies may be used as constant voltage or constant current sources. They may be remotely programmed by means of either voltage or resistance, and have provisions for remote monitoring and output inhibiting. All control and monitoring connections are on a pluggable terminal block that functions as a connector, providing wiring convenience and permitting easy and rapid connect/disconnect. Outputs are arc/short circuit protected.
-
product
High Voltage 50 Ω Pulse Generator
TLP-4010C
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±10 kV*High pulse output current up to ±40 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
product
High Voltage 37 Pin D-Type Cables - Connector to Connector
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
Easy Connection Of IEPE Sensors To Voltage Input Measurement Devices
K- IEPE
Our K-IEPE module is designed to connect IEPE sensors to a voltage measurement device that normally cannot support IEPE sensors. The powered K-IEPE module simply enables IEPE sensors to be connected via the BNC terminals and will output the signal voltages to an analog measurement device.
-
product
Transient Voltage Suppressors (TVS)
A transient voltage suppressor (TVS) is an avalanche diode specially designed to clamp overvoltages and dissipate high transient power surges. ST’s Transil™ protection devices are able to shunt a high current surge for a short duration.
-
product
Stand Alone Low Voltage Testers
Low voltage testers are a special type of device used to identify opens and shorts in applications that are driven on low voltages.
-
product
Probe Oscilloscope High Voltage
High voltage probes allow safe and accurate voltage measurement using your oscilloscope.
-
product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-120-HI
The 40-230-120-HI (PXI) and 42-230-120-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 472Ω with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-141-HI
The 40-230-141-HI (PXI) and 42-230-141-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 201kΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
product
High Voltage Discharge Rod
DSR-50K & DSR-100K
Standard Electric Works Co., Ltd
● For discharging and earthing for cables ● For discharging and earthing of test units● For safety purpose
-
product
NI-9269, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module
781098-01
100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module - The NI‑9269 is a channel‑to‑channel isolated analog output module. The NI‑9269 adds channel‑to‑channel isolation for increased safety and improved signal quality. Channel‑to‑channel isolation is commonly needed for applications that have multiple electrical systems, such as automotive tests, or industrial applications that are subjected to increased noise and often contain multiple ground planes.
-
product
Linear Power Supplies High Voltage, Analog, Digital or Local Control, Ultra Low Ripple/Noise
Series BHK-MG
Kepco's BHK-MG are high voltage, linear, voltage-current stabilizers with rectangular (automatic crossover) output characteristic and ultra low noise and ultra low ripple at the output. All models are MIL-STD-461 compliant. They are offered in two sizes: a 40 watt half-rack design and a 200 watt full-rack power supply. The four models in each size have outputs of 0-300 volts, 0-500 volts, 0-1000 volts and 0-2000 volts. Both digital and analog programming control is featured.
-
product
Proving Unit & Voltage Tester Kit
DLPK1
Touch electrode for Quick testing of fused leads Optical and acoustic continuity Indication Low battery indication A portable, battery powered Proving Unit for testing Two Pole Voltage Testers up to 690V Continuity Tester for testing: Fuses, Fused test leads etc
-
product
GAOTek Portable H/L Voltage Clamp Current Leaker
GT00YA00ZX
The GAOTek Portable H/L Voltage Clamp Current Leaker measures high voltage current with a 12.5 in (32 cm) insulating rod, adopting the latest CT technology and integrating mask digital technology. This instrument provides high precision, reliability, and stability with its integrated design between transducer clamp and domain. This leaker can be used to measure any wire with or without the insulation layer where the voltage is below 10 kV. The insulating rod is portable, moisture resistant, heat resistant, shock resistant, and insulating. It provides additional functionalities such as online current testing, peak and data holding, data storage, detection of high and low current in primary and secondary circuits separately, and provision of suitable calculations to conclude change in high and low pressure.
