Showing recent results 1366 - 1380 of 4804 products found.
-
PT-5000W - HD Electric Company
The PT-5000W is a portable, general purpose dual voltage leakage tester designed to test primary distribution voltage or secondary voltage equipment for faults or high leakage currents. Use only on cables or equipment that have been verified to be both de-energized and discharged. The test voltage can be set by the user to either 500VDC or 5,000VDC. The PT-5000W can be used to check for leakage on cables, transformers, capacitors, joints, terminations, insulators, etc.
-
ST-2120 - Wuhan Sunma Technologies Co., Ltd.
ST2120 E1 service tester, a powerful handheld instrument, providing a scalable, future-proof solution for the testing needs of technicians involved in the installation and maintenance of E1 digital networks. It offers all the error and alarm measurements you will need to verify quality-of-service in your networks. Plus, signal quality measurements including frequency, level and other functions to ensure your costly, time-consuming work performed quickly and efficiently.
-
260 Series - SCI, Inc.
Our 260 Series makes Ground Bond testing simple. We offer two models so that you can have a simple and easy-to-use Ground Bond tester that provides the output current you need to satisfy NRTL specifications. With an intuitive interface that allows you to set-up a test in seconds and practical security settings, our 260 Series can easily be deployed in both laboratory and production line environments.
-
Compliance West USA, Inc
The newest product of our Hipot Line Testers, the UL Listed HT-S series hipot now comes with an adjustable ground continuity test in range of 0.08 - 1.50 , and Auto-offset for test leads up to 1.00 . Performs 0-2000 AC Hipot Test. Neutral/Hot to Ground Leakage current test up to 20 mA AC. Easy to use and connect. Ships complete with cables, manual, and a Calibration Certificate.
-
3PK-NT007N - Prokit's Industries Co., Ltd.
Multi-network cable tester is specified to quickly test by auto scanning the wires continuity, miss-wiring and polarization in your network cables, thin Ethernet (BNC)/10 Base-T (UTP/STP)/356A/ TIA-568A/TIA-568B/Token Ring. By using the attached remote terminator, you can easily test the cable whatever before or after the cables installed. It also allows you to test the ground of shielded twisted pairs cables.
-
Thexton Manufacturing Company, Inc.
Allows technician to test for current drain caused by control modules, computers or other solid state devices. Attaches in-line to negative battery terminal and cable. Current drain is read by connecting ammeter across tester. Used on all computer controlled vehicles since 1980. Eliminates the "shot-gun" method of replacing suspected components. Fits both side terminal and top post batteries. Plated for excellent conductivity.
-
39002 - LANsmart - C2G, Lastar, Inc.
The high-tech LANsmart TDR Cable Tester detects, locates, and displays basic wire connection problems including opens, shorts, miswirings, reversals, split pairs and shield continuity for RJ45, Cat5, Cat6, UTP and STP. Plus, it measures cable length for UTP and STP cable without remotes by using TDR (Time Domain Reflectometer) technology in real time. LANsmart displays the results in a pin-to-pin format.
-
SUG335 - Lisun Electronics Inc.
The SUG335 is a 1.2/50μs Transient Over-voltages Tester. The polarity interval time can be at least 1s. The standard voltage waveform complies with the IEC 60335, IEC61180, IEC 62052-11: 2003, IEC 61008-1: 1996, IEC 61009-1:1996 and IEC 60947-1: 1995, IEC60060, IEC1036 surge voltage test and has been used for safety testing to determine if the clearance was fulfilled the safety requirement while the transient voltage in the circuit.
-
xGenius - ALBEDO Telecom
xGenius is a nice handheld tester equipped with a large (8 inc) capacitive touch-screen to make easier the analysis and results interpretation. It is 100% suitable for labs or field use because is full equipped (IP/Ethernet/PTP/T1/E1), battery operated, light (1.9kg) and very rugged. The unit is able to test Ethernet/IP networks up to 10Gb/s while supporting master/slave Sync-E/PTP emulation and also has interfaces for T1/E1.
-
ScopeTester 5 - DeltaTech Electronics
ScopeTester 5 is 5-channel oscilloscope tester for PC computers. Unlike traditional oscilloscopes it is capable of continuous acquisition of signals without dead times. This feature gives exceptional diagnostic value. Available voltage ranges matches typical signals found in modern cars. The user may connect to vehicle sensors, actuators and other diagnostic equipment, such as current clamps, inductive and capacitive probes and other diagnostic probes.
-
Model-4326 - OYO Corp.
The Point Load Tester is a uniaxial compression testing instrument designed for reading out pressure when a specimen is broken, and it consists mainly of a main unit, a pressure gauge and a hydraulic pump. It is very easy to carry the system and make measurements at a site because of its compact and lightweight design. Also, it takes only a short time to carry out a test, and all the works can be done easily by one person.
-
PTI-816 - PTI Technology Co. LTD
PTI816 is an automatic test equipment which measures the impedance of all electronic components on a loaded printed circuit board. Components such as open/short resistors, capacitors, inductors, diodes, transistors, FET, SCR, LED, ICs, etc. are all the objects for this tester to detect. The opens/ shorts fail, incorrect and disoriented components could be located. The overwhelming functions do help the users to find the faults and improve the quality efficiently.
-
Chroma ATE Inc.
Impulse Winding Tester applied with high/ low inductance test technology has 1000V impulse voltage and 200MHz high speed sampling rate that can satisfy mos t of the power inductors test requirements for wide range of inductance products from 0.1uH to 100uH. The built-in Area Size Comparison, Differential Area Comparison, FLUTTER value and LAPLACIAN value functions are able to inspect the coils for poor insulation effectively.
-
AJIT Electronics Co.
The protective devices such as relays, overload coils, circuit breakers must be checked regularly to ensure that, they are always ready to operate correctly. If a fault occurs in the equipment, which they are protecting, routine relay testing will quickly detect the faulty, incorrectly adjusted protection circuits correctly. It is usually necessary to measure its operating time. The micro controller based time interval meter is used for this purpose in all AJIT brand relay testers.
-
ST-2130 - Wuhan Sunma Technologies Co., Ltd.
ST2130 E1/Datacom tester is one multi-functional and full- featured digital transmission system test device, designed for the installation test, engineering check and acceptance, daily maintenance of digital networks. Mainly performing channel test, alarm analysis, fault finding and signalling analysis. In addition, this instrument further provides various protocol converters with one-way and bi-directional bit error test function. These capabilities make it ideal for field use.
