Showing recent results 1306 - 1320 of 4804 products found.
-
1506 IM - Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Battery operated.● Timer function for hands free use.● Battery indicator.● The tester measure with a frequency of 1kHz.● Measure speaker’s impedance.● Measure speaker lines (connected to load).● Help to calculate and check audio power systems.● Ideal for public address installation and maintenance.● Measure transformer impedances.
-
Atico Export
Capacity of Tester with accuracy of 100g : 250 Kgf. and 500 Kgf.Capacity of Tester with accuracy of 10g : 20 Kgf, 50 Kgf and 100 KgfS Type Load Cell fixed with Top GripTraverse Speed: 300 & 100mm /min.Grip Separation: 1000 mmGrip Separation: 25 mmTop Grip is fixed and Bottom Grip is Movable Type.Elongation measurement by Steel Scale and Digital Counter Meter Both.Digital Display of Load and Elongation.Peak value of last test can be read.User friendly key panel with switch of zero setting and peak value of last testMotor: 1/2 HP single phase 220V 50 Hz. ( for Capacity up to 100 Kgf )Motor: 1 HP single phase 220 V 50 Hz ( for Capacity up to 500 Kgf)Power: 220 V AC 50 Hz.Safety device by limit switch to protect from over traverse.
-
Mitech Co., LTD.
Non-destructive ultrasonic hardness tester, based on the principle of ultrasonic vibration sensor rod, can easily detect a variety of metal materials hardness without damage. Its measurement speed and precision is high and there will be no indentation. It uses advanced sensing system and single chip technology, better than the traditional ultrasonic hardness testers in structure and function. MU200 support value conversion among HRC,HB,HV and others and the multi-point measurement can be averaged. It can also accurately display and print the test results if possible. The product is widely used in hardness testing of finished workpiece, metal foil, metal thin layer (nitriding layer, carburizing layer, electroplating layer, etc.), difficult to move large parts, easy to dismantle the parts and special shape parts.It is one precision testing equipment to improve production pass rate and cost savings .
-
Battery Beak - Cross the Road Electronics, LLC
The Battery Beak is a battery load tester that is capable of delivering an 18 amp load and measuring a batteries internal resistance, state of charge (SOC), and can determine the overall health of the battery. The Battery Beak supports all battery chemistries but has additional features to determine battery health for both Lead Acid and NiMH chemistries and supports a variety of AmpHour/Voltage combinations.
-
DGT-SRT432 - Dandong Flaw Detector Equipment Co., Ltd.
*With slip-up shell, better protection for the tester*Can equip with measuring platform, so that can work-piece of any height. The platform can adjust the height of instruments, can also rotate the instruments 360 degrees*The sensor can be changed, so that we can test work-piece of any shape. Such as groove, hook surface, hole, very small hole, can equip long sensor or lateral transfer sensor
-
PeakTech Prüf- und Messtechnik GmbH
User-friendly tester for non-contact voltage testing from 50 V to 1000 V AC. Suitable for outlets, lamp sockets or against wire insulation testing. If AC voltage is present at the relevant measuring point, this is indicated visually by a flashing red LED and the integrated buzzer sounds. If the measuring point is voltage-free, the test probe lights up permanently green.
-
LMS 20.0 - Maschinenbau Haldenwang GmbH & Co. KG.
The LMS 20.0 axis play tester is used to reliably determine defects and wear on steering parts, wheel bearings, suspension and suspension by means of counter-rotating transverse and longitudinal movement of the test plates. The built-in hydraulic drive ensures a powerful and even movement of the test plates. An automatic mode and other different operating modes make the LMS 20.0 easy to use.
-
PMS 3.5 - Maschinenbau Haldenwang GmbH & Co. KG.
The axis play tester PMS 3.5 is used to reliably determine defects and wear on steering parts, wheel bearings, suspension and suspension by counter-rotating transverse and longitudinal movement of the test plates. The built-in hydraulic drive ensures a powerful and even movement of the test plates. An automatic mode and other different operating modes make the PMS 3.5 easy to use.
-
CBT-500 - Hosa Technology Inc.
The CBT-500 Cable Tester by Hosa Technology diagnoses signal failure in cables terminated with any combination of XLR, Phone, Phono, and speakON® connectors, as well as DIN, Ethernet, 75-ohm BNC, and USB Type A to Type B cables. It is also equipped with removable leads to verify continuity of additional connectors and jacks. Operation requires one 9-volt battery (included).
-
BC-6000 - Concorde Battery Corp.
he BC-6000 Battery Capacity Tester from Concorde. The BC-6000 is designed to accurately test and report on batteries ranging in capacity from 10AH - 50AH. Plugged into a a USB port, the BC-6000 will create test reports directly from your computer. Tests both 12V and 24V lead acid batteries with capacity ratings from 10 AH to 55 AH.
-
BC-7000 - Concorde Battery Corp.
The BC-7000 Battery Capacity Tester from Concorde. Create accurate reports straight from the computer. USB Port access required. Fully automatic testing for 12 Volt AND 24 Volt Lead Acid or Nickel Cadmium Aircraft Batteries. Tests both 12V and 24V lead acid batteries with capacity ratings from 0.5 AH to 50 AH.
-
Morris Products Inc.
Tests & troubleshoots voice communication for open circuits, shorts, miswires, reversals, and split pairsSHIELD detection tests a cable’s shield integrityEasy to read fault display and high speed testingDebug mode for detailed fault identification resultsNetworking Cable Tester has auto sleep mode and power off switch to decrease power consumptionBattery low LED indicator
-
MT2 - Draper Tools Ltd
Multi-functional tester with plain slot blade that allows the checking of wiring without dismantling or having any contact with live parts. Applications include 'break point' in wiring, continuity testing, bulb and fuse testing, microwave leakage, socket testing and testing for static. Fully insulated. Full instructional leaflet supplied. Supplied with 2 x 1.5V alkaline batteries.
-
EVSE LLC
EVSE's Electrician and Technician testers are created for installation professionals, and are small and durableenough to be carried in a toolbox. These weatherproof handheld units allow new chargers to be checked after installation, verifying a number of vital power and safety requirements, as they simulate the connection a charger makes with an electric vehicle. Simply plug the charger's J1772 connector into the tester's receptacle and you are ready to evaluate operation.
-
FA1817 - HIOKI E.E. Corp
Flying Probe Tester FA1817, an automatic testing system designed to inspect printed wiring on bare boards. The FA1817’s features and capabilities make it ideal for use in inspecting high-density printed wiring boards. With support for a broad range of test types, from low-resistance measurement to high-insulation-resistance measurement, the system reliably detects the latent defects that trouble end-users.
