Showing recent results 541 - 555 of 4817 products found.
-
HIACC Engineering & Services Pvt. Ltd.
Drop test system is used to simulate fall condition to determine the drop bearing capacity of the specimen to in the transportation and handling process. The specimen’s surface, edges and corners are tested for its reliability & fatigue. The test insights will support you in improving and perfecting the package design.
-
MS-158 - Misum Systech Co., Ltd.
This equipment is used for inspecting state of earphonethroughmeasurement of resistor, consumption current and sensivity. Depends on the setting value, OK or NG will displayed.
-
ET-F 1501 - Musashi Intek Inc.
Measurement methods that do not require a 2-pole auxiliary ground rods Direct reading measurement of species B and D With false alarm lamp wiring Earth leakage breaker (ELB) does not work Measuring the current limited
-
ET-5 1500 - Musashi Intek Inc.
To hit the ground where aid can be measured by simply placing the concrete in place, waterEasily measure the ground resistance of species A, B, C & DIn short bar with a simple measurement method (2-pole) corresponds toVoltage can be measured
-
Kyoritsu Electrical Instruments Works, Ltd.
Earth Ground Testing. Most facilities have grounded electrical systems, so that in the event of a lightning strike or utility overvoltage, current will find a safe path to earth. A ground electrode provides the contact between the electrical system and the earth.
-
Sanwa Electric Instrument Co., Ltd
Most facilities have grounded electrical systems, so that in the event of a lightning strike or utility overvoltage, current will find a safe path to earth. A ground electrode provides the contact between the electrical system and the earth.
-
GCR-3N 2211 GR - Musashi Intek Inc.
In addition to extensive testing GR, condensed into a compact body of the ELB test functionsEasily be tested by the inertial properties of the GR test MCU controlThe test output can start testing the exact zero-cross methodELB test is compatible with 100V testing and unit testing of hot-100V/200VThe minimum operating current study and the GR ELB can be tested without precise reading errors automatically to increase the test current
-
Control Company
Designed specifically for easy and intuitive use. After one minute, you’ll never again look at the directions. LCD displays exactly which measurement is being made. Audible beep confirms each measurement. Three distance memories and one calculation memory are maintained even when the unit is off. Calculator function permits addition/subtraction of readings.
-
Precision Mastech Enterprises Co.
AC Voltage range: 50V-1000V AC, 50/60HzSafety standards: Designed to international safety standard IEC61010 - 1/600V CAT III, 1000V CAT II.Battery: 2*1.5V (AAA type)Altitude: <2000mOperating temperature: -10 to 50CStorage temperature: -20 to 60CHumidity: <85% relative humidityDimensions: 157*24*20 mmWeight: Approximately 42g
-
all-sun
This hand-held digital logic probe provides convenient and precise use in the measurement of logic circuits. It displays logic levels (high or low), pulses and voltage transients down to 25 nanoseconds. High intensity LED readouts provide instant response to the logic state. Tests all logic families TTL/LSI, and CMOS/MOS digital circuits.
-
TES Electrical Electronic Corp.
Frequency range 10MHz to 8.0 GHz3 axis isoltropic measurements of EMFNon-directional measurement with three channel measurment probe. High dynamic range.Configurable alarm threshold and memory function.
-
ALL-TEST Pro, LLC
Two complete instruments in one: Electric Signature Analyzer (ESA) and a Power Quality Analyzer (PQ)ESA mode evaluates the condition of incoming power, the control circuit, the motor itself, and the driven loadPQ mode used for energy data logging, harmonic analysis, voltage and current charting, viewing and capturing waveforms, including sags and swells, transient capture and event captureResults can be trended for condition based maintenance/predictive maintenance purposes
-
AEMC Instruments
AEMC manufactures a line of cost effective, hand-held instruments for measuring temperature, humidity, light, wind speed and other variables. Each instrument in this series includes sensor, backlit CD and a shockproof holster. They are battery operated and can easily be carried in a shirt pocket.
-
B&K Precision Corporation
Environmental tests are used to verify a piece of equipment can withstand the rigors of harsh environments.
-
KT-200SG - Kast Eng Co. LTD.
This test instrument stands for the EMI(Electro Magnetic Immunity) ability test to the electric devices, electronic circuit boards & electric equipments. Recently this instrument is widly used in many companies in Korea & other countries to test the immunity to thier products-power supply, drive PCBs, communication systems, LCD display panels whether they are safe or not against the impulse & noise.All for the purpose, of this object, it generates 4 ~ 5 kinds of different impulse test waveforms.Output test voltage level : 5 ~ 200 V ImpulseOutput voltage polarity : Positive, NegativeType of waveforms
