Testers
find the limits of a design and assure designed requirements.
See Also: Test, Testing, Specimen, Audio Testers, Automotive Testers, Battery Testers, Cable Testers, Component Testers, Checkers
-
product
Insulation & Multifunction Tester (LCD Display)
4167 MF
Standard Electric Works Co., Ltd
● High Quality Taut Band movement.● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● Test test leads are supplied as standard accessories for simplified two-wire measuring system.● Two insulation test voltages(DC) : 250V and 500V.● Alternation voltage measurement.● Battery life indicator.● Fuse protected.
-
product
Software
AFK-9110
Wired testers of the TEST-9110 series have been produced in series since 2006 and are well known to Russian and foreign consumers. As of the beginning of 2017, more than 250 sets of TEST-9110 series systems are in operation. Up to now, two types of software have been supplied with them: this is the AKM software and the cyclogram translator software. Now these programs have been revised into the AFK-9110 software.
-
product
Hand Cranked Analog Insulation Resistance Tester
IRT20
UEi Test & Measurement Instruments
The IRT20 is a Hand-cranked Insulation Resistance Tester. With a insulation resistance range of 0.1 to 1000MΩ, 250, 500 and 1000V output ranges and accurate to with in one division. It is in a sealed, water resistant, rugged metal housing and is backed by a 1-Year limited warranty.
-
product
BMS Tester
MS-159
This equipment used for F/W writing, Calibration and function test. It inspect current, voltage protection mode, consumption current and cell balancing measurement to check the state of BMS and applied to the full inspection and mass production.
-
product
BERTScope Digital Pre-emphasis
DPP Series
The Digital Pre-emphasis Processor DPP Series takes in single-ended inputs of data and clock and conditions the signal by adding precision amounts of pre-emphasis for use with Bit Error Rate Testers. Nine Tap Linear Equalization supporting speeds up to 32Gb/s is supported with the LE320 Series remote head, offering compact two channel precision equalization.
-
product
Smart Card Testers
CT1000
The CT1000 testers are open and configurable to test any kind of communication protocols used on smart cards, and to be updated for new technologies. The systems can test devices that use common standard protocols (as ISO 18000, EPC Global Gen 2, ISO 14443, ISO 15693, MIFARE™, DESFIRE™, FeliCa™, ISO 11784/85, ICode™, Hitag™, ISO 7816, ISO 7813), and are ready to test also the next generation of cards protocols, such as: USB-Keys, MMC, Micro-SD (with and without CPU inside), M-SIM, HD-SIM, SIM-WAVE, and I2C.
-
product
ICI Mace Snag Tester
TF220
TESTEX Testing Equipment Systems Ltd.
ICI Mace Snag Tester. To determine the tendency of fabrics to snag (pull yarn loops from fabric) in normal wear (mace snag).Provided with 4 rotating test cylinders fitted with sleeves of test fabric, mace balls with tungsten carbide points and controlled by a predetermined electronic counter.
-
product
2-Channel Mandrel Free IL/RL Test Station
Shanghai Fibretool Technology Co.,Ltd.
This test station is designed specially for different connector on both sides patch cord(such as FC-SC, FC-LC, SC-LC…) and the duplex patch cord.The REF for insertion and return loss can set one time for those kind of patch cord, no need to change standard patch cord and interchange testing port connector on tester( Especially 2.5mm and 1.25mm interchange). For the tested patch cord, APC end no need to manually set standard patch cord length if PC end measured shortest length is 2.2M.
-
product
Flying Probe Tester
Condor MTS 505
Primarily the Flying Probe Tester was developed to enable In-Circuit testing (ICT) of prototype PCBs. For testing a new design an existing fixture has to be changed or a new fixture has to be procured. The fixtureless design of the MTS 505 Condor is one of its most attractive properties, where the unnecessary and costly time delays incurred for fixture build or changes can be avoided. It is the ideal platform for testing prototypes.
-
product
Aging and Optical Attenuation Tester
LS822
• Build-in DC Power Supply: Forward current preset: 0.1-800mA (special order) Range of forward voltage: 0.1-20.00V • Range of luminous intensity: 1mcd-3,000cd • Range of luminous flux: 1mlm-9,999,000lm(depends on the size of sphere) • Accuracy of photometer: class1; accuracy of electricity: class0.5 • Aging time: 9999Hours 59Munites 59Seconds • Tolerance of time: ±1S/10H • Record time: 16000times • Hold data automatically when the power is off and continue to work automatically when the power is turned on.
-
product
Polysilicon Resistivity Tester
HS-POSRT
HS-POSRT polysilicon resistivity tester is an advanced resistivity tester, it has features of wide resistivity measuring range, high testing accuracy, high stability, swift body and easy operation. It is a good friend to Siemens polysilicon material producer,SH4 polysilicon material producer, UMG polysilicon material poroducer and so on
-
product
Waterproof Eco Tester EC High
EcoTestr EC High
The Eutech EcoTestr EC series comes with rugged, sturdy stainless steel pin sensors, giving you quick, reliable conductivity measurements. Ideal for use in a wide range of conductivity applications, such as hydroponics gardening, fish-farming, pools, electroplating and other water/ wastewater applications.
-
product
Waterproof Dual Range Tester
ECTestr 11
User-Replaceable Sensor - Replace the sensors yourself. Sensors lasts longer with element made of SS316 stainless steel and sensor casing made of VALOX®
-
product
Drop-In In-Circuit Test Fixtures
The Chameleon
The Circuit Check kit called the Chameleon allows easy re-use of a majority of an ICT fixture’s major components. The Chameleon includes a full size probe plate and interface alignment plate so all valuable tester resources are available. The probe plate assembly is held in place with twelve (12) screws and the vacuum box’s interchangeable push plate is easily replaced by removing four (4) shoulder screws.
-
product
Tachometer Tester
Series 1921
The Model 1921 Tachometer Tester is used for the testing and calibration of electrical and mechanical tachometer generators and indicators.
-
product
AC Motor Tester
JK115
Shanghai Aoboor Electric Co., Ltd.
Applicable to electrical performance test of single-speed, multiple-speed single-phase induction motors.
-
product
PSS PCB Tester
MS 1106
PSS PCB Tester is a powerful system used to test and validate DAWN (RWR & JAMMER) Support System boards. It has RS232/USB Communication for PC Interface.
-
product
Manhole Mechanical Properties Tester
Manhole mechanical property tester is designed to determine the performance of inspection chamber, manhole frame as well as manhole wall. It can be used to test shear strength and the axial loading performance of manhole base. It can also be used to test Ring stiffness, flatness and ring flexibility test.
-
product
Digital Circuit Tester 3-49V
28830
Operating range of 3-49 volts DC to work on most vehicle electrical systems. 360° visibility of polarity. The red light indicates positive polarity, green indicates negative polarity. Long, 12ft. coil cord and heavy-duty alligator clamp for secure connections. The probe is insulated to prevent the possibility of shorting the side of the probe to other components.
-
product
Mini Appliance Checker
880 AT
Standard Electric Works Co., Ltd
● The 880 AT is a simplified Version of an appliance tester which use low voltage and low current to perform it's checks.● Application Example The appliance is plugged into the mini appliance checker, then the probe make contact with the protective conductor.● Other appliance checking Washing Machine Toaster Iron Dish Washer Stove
-
product
Flying Probe Tester
FA1817
Flying Probe Tester FA1817, an automatic testing system designed to inspect printed wiring on bare boards. The FA1817’s features and capabilities make it ideal for use in inspecting high-density printed wiring boards. With support for a broad range of test types, from low-resistance measurement to high-insulation-resistance measurement, the system reliably detects the latent defects that trouble end-users.
-
product
EOS Tester
KT-200SG
This test instrument stands for the EMI(Electro Magnetic Immunity) ability test to the electric devices, electronic circuit boards & electric equipments. Recently this instrument is widly used in many companies in Korea & other countries to test the immunity to thier products-power supply, drive PCBs, communication systems, LCD display panels whether they are safe or not against the impulse & noise.All for the purpose, of this object, it generates 4 ~ 5 kinds of different impulse test waveforms.Output test voltage level : 5 ~ 200 V ImpulseOutput voltage polarity : Positive, NegativeType of waveforms
-
product
Insulation Multimeter
VA588
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
VA588 Insulation Multimeters combine a digital insulation tester with a full-featured digital multimeter in a single, compact.
-
product
Combination Exhaust Tester for Petrol- and Diesel- Powered Vehicles with Innovative Condensate Separation
MET 6.3 | VP 135213
Maschinenbau Haldenwang GmbH & Co. KG.
The combination tester is designed for the measurement of petrol- and diesel-powered vehicles. The MET 6.3 stands out for its innovative condensate separation thanks to an active water separator. In addition, low weight, compact design and short warm-up time ensure easy handling. Part of the equipment is a 2 m (optional 4 m) long probe for both engine types.
-
product
Drivetrain Tester
G5.DT
The G5.DT series is bidirectional regenerative. It was developed specifically for testing DC components of the electrical drive train or DC components of other parts of the vehicle electrical system. It is suitable for use in laboratories and on test benches. The modular and finely graded G5.DT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies are equipped with a powerful CAN multi-protocol interface (1 kHz, 16 bit) and optionally offer test bench relevant safety functions such as PL e according to EN ISO 13849, insulation monitoring as well as automatic discharge on the load side in case of shutdown.
-
product
High Speed Cable Production Tester
GRL-V-DI20
GRL-V-DI20 provides a fast and easy way for anyone to test cables for manufacturing defects and signal integrity specification requirements. GRL-V-DI20 provides comprehensive test coverage in seconds at a fraction of the cost of similarly-capable bench test equipment.
-
product
Automatic Oil Tester
Theses tester sets are used for determining the di-electric BDV of insulating oils, both new and in-service from transformers, switchgear and other electrical equipments.
-
product
Tribology System
UMT TriboLab™
Bruker’s Universal Mechanical Tester (UMT) platform has been the most versatile and widely used tribometer on the market since the first model debuted in 2000. Now, newly designed from the ground up, the UMT TriboLab™ builds on that legacy of versatility with a unique modular concept that harnesses more functionality than ever before—all without any compromise in performance.
-
product
Trailer Wire Plug Tester
Plug these testers into any car connector and you will have an instant test of running light circuits. Features LED display to show completed circuit for the running lights left turn signal and right turn signal. Auxiliary and electric brake circuit are included on the 6-way tester and auxiliary, electric brake and battery charge are included with the 7-way tester. One piece units with internal ground. Proper installation and set-up of a brake control, when a trailer is not readily available, is possible with the 7-way tester.
-
product
Ultrasonic Hardness Tester
Sinowon Innovation Metrology Manufacture Ltd.
◆ Perfect Accuracy——±3% HV, ±1.5HR, ±3%HB.◆ Microscopic Indentation—— Only high-power microscope can observe the indentation.◆ Quick Measurement——Result in 2 seconds.◆ Large LCD Display——Directly display measurement result, times count, maximum, minimal, average and deviation.◆ Friendly Operation——Operate well after short training.◆ Promised Warranty——2-Year warranty for main unit (Excludes Probe).◆ Mass Storage——Save 1000 groups measurement data.◆ Simple Calibration——Save 20 groups calibration data for invoking, improve calibration efficiency.