Sensors
detect a physical event then translate to a representative analog signal.
See Also: Measurement, Detectors, Meters, Transducers
-
product
Hyperspectral Imaging Sensors
HYPERSPEC® sensors are line-scanning instruments (sometimes called pushbroom) that collect reflected light through an image slit. One row of spatial pixels is collected per frame as motion occurs, with each pixel containing full spectral data. Motion can be accomplished in two ways: either as an airborne deployment (UAV, aircraft, or satellite) or stationary (where motion is accomplished beneath the sensor, such as a food inspection line). A third option is also available where pan-and-tilt or rotary stages allow a fixed-location sensor to scan a stationary object (such as a piece of artwork, or a mine face for geological applications).
-
product
MEMS DC Response Accelerometers
PCB® series 3711F, 3713F, 3741F, and 3743F MEMS DC response sensors are used to measure low frequency motion down to zero hertz. These accelerometers are used in applications such as structural monitoring, aerospace vibration testing, drivability, and gravitational force measurements. Each series includes a full scale measurement range from ± 2g to ± 200g and features low spectral noise with high resolution.
-
product
Gas
For toxic and combustible gas, as well as refrigerant leak detection, ACI’s line of gas sensors will solve the most challenging applications with the fewest devices and lowest total installed cost
-
product
IR Receivers
Vishay is the world's leading supplier of infrared (IR) receivers. Vishay IR Receivers offer a breadth of products, holders, application and technical support, and overall knowledge of infrared communication; infrared code learning, infrared light barriers, infrared proximity sensors including reflective sensors. Vishay's IR receivers are used for remote control and for transmissive and reflective sensors.
-
product
Photon Sensors
Nordson Measurement & Control Solutions
Electrode Coat Weight Gauging of Anode and Cathode for Lithium Ion Batteries
-
product
16-bit, 200KHz, 8SE/4DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3116-8
The APCI-3116 is a 16-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3116, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
product
Chilled Mirror Hygrometer
DewMaster
One, two or three stage sensors available - integral or remote from controller.NIST traceable calibration certificate.Depression range choice of either 45, 65 or 95°C . (one, two or three-stage cooling)Automatic Balance Control (ABC)
-
product
Industrial ICP® Strain Sensors
For Process Monitoring/Quality Control. The Industrial ICP® Strain Sensors incorporate piezoelectric quartz sensing crystals that respond to a longitudinal change in distance. The resultant strain measurand is an indirect measurement of stress forces acting along the structure to which the sensor is mounted. As such, these devices can provide insight into the behavior of mechanical systems or processes that generate an associated machinery reaction.
-
product
SHSLab Wavefront Sensors
The SHSLab wavefront sensor system is a powerful and comprehensive measurement solution for a multitude of optical applications, such as:*alignment of optical systems *measurement of imaging quality*surface shape measurement*laser beam characterization
-
product
PXI Strain Gauge Simulator Module 2-Channel, 1.5K
40-265-402
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 1.5Ω) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
Software-controlled Generator
IPTN16
*The module provides output of constant stabilized voltage through 16 independent channels in 2 ranges ± 2 V and ± 10 V with a step of 5 mV, as well as a stabilized current of ± 10 mA with a step of 5 μA.The IPTN16 module is intended for use in information measuring VXI systems and can be used to power resistive temperature sensors or strain gauges with voltage or current with an accurate and stable value.*The IPTN16 module can also be used to simulate voltage or current sensors when checking measuring instruments and channels of measuring systems.
-
product
Sensors
The large selection of sensors and the modular design of the multisensor coordinate measuring machines enable application-specific device configurations. The use of multi-sensor systems allows the economical solution of many measuring tasks with just one measuring machine, which in the past required many different machines. This minimizes investments, maintenance costs and set-up times.
-
product
PXI BRIC8 FIBO Matrix Dual 60x4 3pin brkout
40-592A-103
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units.
-
product
Precision Sensors for Aerospace
IC² delivers scientific-grade precision sensors that push the envelope of aerospace measurement accuracy and performance. Offering a suite of sensors and instrumentation for aerodynamic and aeroacoustic measurement applications, including direct-measurement shear stress sensors, aeroacoustic microphones and dynamic pressure sensors and arrays, our sensors are designed to meet rigorous performance specs and survive harsh environments, making them ideal for wind-tunnel and in-flight measurements.
-
product
Thermocouple Data Logger
IM2000 Series
We have been offering IM2000 Series Thermocouple Data Logger with direct interfaces for various types like J / K / R / S / T / B / E etc. Loggers have built in ambient compensation. The thermocouples are most commonly used sensors for measuring temperature in process industries. These can take any form and are available in various mechanical shapes. The temperature ranges are varied.
-
product
Subsea Imagery
With only 24% of the ocean floor being mapped with a submetric resolution, the ocean’s seabed is Earth’s last frontier. Mapping the seafloor, protecting marine habitats, hunting for wrecks, studying underwater geo-hazards…Those are challenges for the years to come.It is to help in that field, that Exail has developed a large range of sensors designed to address the full spectrum of subsea imagery applications, from sub-bottom profiling and seabed mapping to water column monitoring.
-
product
Interrogator
FAZT I4G
The FAZT I4G Interrogator is an optical sensor interrogators. Supports multiple modes of operation including ultra repeatable performance (< 0.010pm) and fast sampling speeds 1Khz, 2Khz, 4Khz and 8Khz, spectral sensors (FP, MOF etc) and bi-refringment sensors (PM-FBG).
-
product
FD-11637, 8-Channel Strain/Bridge Input Device for FieldDAQ
785641-01
8-Channel Strain/Bridge Input Device for FieldDAQ - The FD-11637 can measure eight channels and has built-in bridge completion and voltage excitation to support for quarter-, half-, and full-bridge sensors. It also features anti-alias filtering, offset nulling, and shunt calibration to reduce the effect of noise and improve measurement accuracy. The FD-11637 has an ingress protection rating up to IP67 (dust- and water-resistant), can operate in -40 °C to 85 °C environments, and can sustain 100 g...show more -
product
Fixed Toxic Gas Detector
CTX 300
Teledyne Gas & Flame Detection
When hazardous levels of toxic gases or oxygen threaten the safety of an unclassified area, the CTX 300 detector can satisfy the most demanding safety requirements.The CTX 300 detector is designed to detect oxygen, toxic and refrigerant gases, and also uses a new sensor for CO2 detection over three different ranges: 0-5000 ppm, 0-5% vol. and 0-100% vol.The CTX 300 transmits data in record time. With a wide range of sensor options, it has the flexibility to protect many potentially hazardous environments.Maintaining the unit is easy with pre-calibrated sensors and an optional LCD display.
-
product
Radar Test System
UTP 5065
Radar sensors are core elements to realize autonomous driving. The UTP 5065 radar test system from NOFFZ Technologies has a compact vertical design and contains everything needed to allow State-of-the-Art measurement and sensor calibration. The test bench setup and component selection are tuned to get best possible results for highly accurate and cost-efficient testing in production of automotive radar sensors.
-
product
AMR Linear Sensors
MultiDimension Technology Co.,Ltd.
AMR linear sensor utilizes two push-pull Wheatstone bridges each composed of four highly sensitive AMR sensor elements. These Wheatstone bridges effectively compensate the sensor’s temperature drift to achieve outstanding temperature stability with minimal noise.
-
product
Pressure Sensors
At the heart of every Tekscan pressure measurement system is an ultra-thin, tactile pressure sensor. Every Tekscan sensor is comprised of numerous individual sensing elements, or sensels. The sensel density represents the total number of sensels per unit of area. In order to use Tekscan's pressure sensors, you must have a Tekscan pressure measurement system as well as the corresponding sensor map (software driver) for the sensor.
-
product
Sport Sensor Range
DHE (Differential Hall Effect) sensors give an output when subjected to a changing magnetic field. The field is set up by a magnet inside the sensor body and changes when ferromagnetic teeth are passed beneath the sensor (no magnets are required in the target). To improve noise resistance, the sensor has two Hall effect elements and only responds to changes in magnetic field strength corresponding to tooth passing frequencies above 15Hz. As each tooth passes the sensor, the digital state of the output changes
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-125
The 40-297A-125 (PXI) and the 42-297A-125 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 13.6 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
General Data Acquisition Device With Strain Gage Measurement
Spider-80SG
The Spider-80SG is a high precision, general purpose data acquisition device featuring strain gage measurement. This device can be used in a variety of physical and measurement tests. The Spider-80SG can acquire data from a strain gage or a wide range of measurement quantities. A variety of general purpose and strain gage based sensors are supported. The Spider-80SG is built on the proven outstanding performance and reliability of Crystal Instruments’ DSP-based hardware platform. It features the...show more -
product
A²B® Automotive Audio Bus Solution
ITD 1024
ITD 1024 is an off-the-shelf solution for A²B®, an emerging automotive audio bus. In combination with a comprehensive set of software tools, ITD 1024 allows rapid testing of various A²B® components such as audio speakers, amplifiers, microphone arrays, sensors, and actuators.
-
product
Three Axis Accelerometers
TAA
The Inertial Labs MEMS TAA-308, TAA-315 and TAA-340 are the third generation of the Inertial Labs MEMS, three-axis high-precision accelerometers released in a stand-alone design. The TAA-308, TAA-315 and TAA-340 are revolutionary, compact, self-contained, strapdown, Navigation-grade Accelerometers that measure linear accelerations with high precision due to their unique design and developed by Inertial Labs over last 20 years several significant know-know and technics in calibrations of inertial sensors. Measured by TAA Accelerometers accelerations are determined with low noise and very good repeatability for both motionless and dynamic applications.
-
product
CMOS Image Sensors
Since 1999 ST has been an industry leader in the design and manufacture of imaging sensors. The current product portfolio spans a wide range of traditional image sensors from entry level VGA to 24 Mpixels and will soon offer products with 100’s of millions of pixels.
-
product
AS-Interface Systems and Sensors
*Airboxes for the combination of AS-i inputs and pneumatic output valves*Dual inductive sensors for quarter-turn actuator feedback*Position feedback for single and double seat valve and for diaphragm valves*Inductive sensors for coolant applications*RFID for track and trace applications
-
product
Air Temperature and Relative Humidity Sensors
Air temperature and relative humidity probes typically consist of two separate sensors packaged in the same housing. Often relative humidity is measured with a capacitive RH sensor, while air temperature is measured by a PRT.
