McLAREN Applied Technologies
Technology is the lifeblood of the McLaren Group. It drives our motorsport and automotive success, which in turn creates an infrastructure geared to further innovation. As part of the Group, McLaren Applied Technologies is uniquely positioned to capitalise on progress made within the broader business.
- +44 (0)1483 261 400
- sales@mclaren.com
- McLaren Technology Centre
Chertsey Road
Woking, Surrey GU21 4YH
United Kingdom
-
product
Linear Hall Sensor
The output of a hall effect sensor is a voltage which changes in proportion to the shaft extension. A constant voltage is required across the supply and ground wires of the sensor. The sensor consists of a Hall Effect element, and a shaft which houses a magnet. When the position of the sensor changes relative to the shaft, the change in magnetic field in the sensor results in a change in output voltage.
-
product
Thermocouple
This sensor uses a K-type Chromel/Alumel thermocouple and is intended for use in high-temperature, high-vibration environments. Control units and data loggers support K-type thermocouples. The sensor is short and compact to minimise its susceptibility to vibration.
-
product
CDI Ignition Coil
An on-plug coil for use with Capacitive Discharge Ignition (CDI). Design and manufacture is in-house, so we can make the coil to suit your specific application. The information given here is for a typical coil. Many of the parameters can be tailored to a particular installation.
-
product
Ignition Driver Units
A compact inductive ignition drive unit which drives two banks of five ignition coils. The drivers are controlled via direct logic signals from a host ECU and provide fire-by-fire diagnostics back to that unit via CAN. The coils can be run at voltages up to 30V with this unit in order to minimize dwell times for optimum response.
-
product
Thermal Camera
The thermal camera allows real-time thermography with 100Hz frame rate via USB 2.0 interface. The camera is lightweight, compact and rugged (IP65). Measurement ranges of -20C to 100C, 0C to 250C, or 150C to 900C are selectable in software. Interchangeable lenses are available with 6x5, 23x17, 48x31 and 72x52 field of view.
-
product
Fluid Level Sensor
The output of the fluid level sensor is a voltage which changes in direct proportion to the level of fluid in the probe. The difference in permittivity between air and the fluid being measured changes the capacitance between the probe's two concentric tubes as the level changes. An RS232 connection to a PC allows the user to calibrate the fluid level and thermal drift compensation. The probe is factory replaceable, allowing the electronics to be re-used should the probe become damaged or if a new probe length is required.
-
product
Calibration Software
System Monitor is a software package for configuring and tuning automotive control systems. It has built-in support for motor sport systems and can be tailored to support third party control units.System Monitor not only allows you to tune data for your program versions, but also manages those versions on disk, allowing them to be located quickly for programming or modification
-
product
Rotary Hall Effect Sensor
The output of the Rotary Hall-effect sensor is a voltage which changes in direct proportion to the shaft angle. The sensor is non-contact, using Hall elements to determine the angle of a magnet. The magnet is either mounted in a shaft integral to the sensor or can be mounted externally to the sensor.
-
product
Microwave Transmitter
LTX-310B
LTX-310B is a self-contained microwave transmitter for use with the LRX-310B receiver. The output is pulse modulated to identify one of 36 channels arranged in six groups of six. The group is set at the factory and you can select one of the six channels in that group from an external rotary switch.
-
product
Interface Units
intelligent, microprocessor controlled, data acquisition and lambda measurement unit for up to 6 wide band UEGO sensors. It is based on the sensor node and can be used as part of the DATA
-
product
Torque Systems
The Drive Plate Torque System uses a low power radio link to transfer digitised strain measurements from a rotating wheel hub to a stationary antenna mounted nearby. The signals are passed to a receiver where they are decoded and output as CAN bus messages and analogue outputs.
-
product
Accelerometers
The unit is based on micro machined MEMS technology. The unit contains a 35g sensing element. The element is scaled to optimise the resolution to suit the g range of interest. An internal amplifier provides an output between 0 and 5 volts. The on board microcontroller and temperature sensor are used for offset drift compensation. This unit can be re-calibrated at the factory.
-
product
Tyre Pressure and Infra-Red Sensors
The system consists of a powered pressure and temperature sensor with transmitter fitted to a wheel rim. This sends pressure and temperature data over an RF link to a compact receiver on the car. Sampling rates increase automatically when either a change in pressure is detected or when wheel inertia is detected. The system stops transmitting below a threshold pressure to preserve battery life. The receiver sends data to the car control via CAN.
-
product
Pressure Sensors
The output voltage changes with the absolute pressure applied to the pressure port. The gain, offset and thermal drift of the pressure sensor is digitally compensated to minimise errors and to create a single-ended, amplified output in the 0 to 5 Volt range.
-
product
Temperature Sensors
Temperature sensors have a well-defined relationship between electrical resistance and temperature, allowing them to measure temperature precisely. The sensor body is made of a thermally conductive material and is as small as possible to produce a rugged device which gives an accurate measurement of temperature with a fast response.
