Showing results: 586 - 600 of 2653 items found.
-
Guildline Instruments Ltd
Programmable Teraohmmeter makes resistance measurements up to 10 PΩ. Whether used in automated mode via the Guildline developed TeraCal Software or as a stand-alone meter, the 6520 provides a fully automated method for calibrating both high and ultra-high resistance values and allows for direct Surface and Volume measurements.
-
PGB-745 -
Prostat Corporation
- Designed for measuring charge movement and decay time of ESD controlled materials- The set consists of two stainless steel electrodes and two very high resistance test leads selected for this application- The high resistance leads minimize leakage during the test cycle and are equipped with male banana plugs
-
40-121-012 -
Pickering Interfaces Ltd.
The 40-121-012 provides 8x 2:1 multiplexers in a single slot PXI module and designed to provide an isolation resistance in excess of 1013Ω. It has been designed to ensure high isolation resistance through the use of switched guards, making it ideal for low level measurements and semiconductor test.
-
Anton Paar GmbH
Scratch testers from Anton Paar are used to characterize film-substrate systems and to quantify parameters such as adhesive strength and friction force by using a variety of complementary methods. This makes scratch testers invaluable tools for the determination of coating adhesion, scratch resistance, and mar resistance in research, development, and quality control.
-
40-121-011 -
Pickering Interfaces Ltd.
The 40-121-011 provides 16x 2:1 multiplexers in a single slot PXI module and designed to provide an isolation resistance in excess of 1013Ω. It has been designed to ensure high isolation resistance through the use of switched guards, making it ideal for low level measurements and semiconductor test.
-
PU 187.21 -
Metra Blansko a.s.
Instrument PU 187.21 MEGMET 1000 D is intended for measurements of the insulation resistance up to 20 GΩ and the resistance of protective conductor up to 2 kΩ, its length; it can be used for checking the over-voltage protections. It also measures DC / AC voltage up to 1000 V and the temperature within the range -20 °C ÷ 120 °C, with a connected external sensor within the range -50 ÷ 850 °C. Nominal measuring voltages for the insulation resistance measurements are 50, 100, 250, 500, and 1000 V.
-
Sataton Instruments Technology CO., Ltd
By providing a defined load, a translational movement tracing a Lissajous figure and abrasive medium, martindale abrasion tester is professional designed for determining of the abrasion resistance of fabrics including specimen breakdown, mass loss and appearance change. The tester can also use to determine the resistance to pilling and surface change of textile fabrics. With accessories, the tester is to determine abrasion resistance of lining and insock for personal protective footwear. It is widely used to evaluate the properties of clothes fabrics, coating materials, wool fabrics, nonwovens and other special materials for protective equipment.
-
MZC-304 -
Sonel S.A.
# Measurements of impedance in a short circuit loop.- L-PE circuit,- L-N, L-L circuit,- L-PE(RCD) circuit - without tripping the circuit breaker > 30mA.# Low voltage resistance measurement:- continuity measurement - DC current +200mA with wire resistivity reset- low current resistance measurement with accoustic signalling,
-
MFJ-202B -
MFJ Enterprises, Inc.
Quickly adjust almost any antenna for maximum performance, 1 to 100 MHz. Lengthen or shorten your antenna for minimum SWR. Measure resonant frequency, feedpoint resistance and reactance. Works with any receiver or transceiver. Hand-calibrated resistance scale, expanded capacitance range and exclusive built-in range extender.
-
PU 590 -
Metra Blansko a.s.
The instrument PU 590 is intended for measurement of the insulation resistances and voltages in insulated IT networks, signalling and safety systems or at presence of disturbing voltage. PU 590 can also be used for common measurements of the insulation resistances. It complies with the requirements of the CSN EN 61557-2 ed.2 and CSN EN 61010-1ed.2 standards.
-
Hong Kong Songyang Industrial Ltd.
They have the features of compact size, beautiful appearance, high sensitivity, accurate measurement, good stability, strong reliability, high-pressure resistance, corrosion resistance, longer service life and easier maintenance. They are better suitable for measuring flow-rate mediums of Liquefied petroleum gas, Natural gas, Town gas respectively.
-
EUROSMC, S.A.
Portable equipment designed for maintenance and commissioning of substations and power plants. Low resistance micro ohmmeters, digital timers, windings resistance, contact resistance, circuit breaker timing and motion, phase angle and frequency measurements.
-
CPV-4 -
Tinker & Rasor
The CPV-4 is a DC digital voltmeter with a input resistance of 20 meg ohm and two voltage ranges
-
-
MRC ltd.
LCR meter is used to measure the inductance (L), capacitance (C) and resistance (R) of an electronic component.