Product

IP67 Testing

-

Cincinnati Test Systems

Cincinnati Test Systems

IP67 is an electronics and sealed device attribute requirement with a physical no-water ingress testing process used to determine whether components meet the requirements needed to receive an IP (ingress protection) rating. Devices with this internationally recognized rating resist exposure to dust and withstand up to 30 minutes of submersion in water up to 40 inches (1 meter) in depth. Products assigned an IP67 rating are typically used in outdoor applications or other environments requiring resistance to dust, moisture, and water submersion.

Product

Slip Testing (Articulated Strut) (Mark II)

SG-P07MII

-

Jinge Testing Machine Co.,Ltd

SG-P07MII - Jinge Testing Machine Co.,Ltd

It's used to determine the slip resistance of footwear sole, heel or related materials against planar walkway surface or walkway surrogates under dry, wet or contaminated conditions.

Product

Open/Leak Tester

-

Nidec-Read Corporation

Nidec-Read Corporation

NIDEC-READ testers undertake various types of continuity tests at broad voltage and resistance levels.

Product

500 MHz Passive Probe for WaveJet Touch, 10:1, 10 MOhm

PP006D

-

Teledyne LeCroy

PP006D - Teledyne LeCroy

Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.

Product

Battery Monitoring System

FST-TA

-

Foresight Electronics Co., Ltd.

FST-TA - Foresight Electronics Co., Ltd.

Continuous 24/7 on-line monitoring One CELLCHECK monitor one cell, including internal resistance, voltage and temperature Software is available to collect data from CELLCHECK Serial port with Optical isolation, meet MODBUS protocol, easy to be accessed by UPS controller Easy to install without specialized training Full resistance, battery temperature and voltage monitoring for comprehensive battery state of health analysis String current and ambient temperature monitoring

Product

Quad Scanner

Model 164B

-

Data Proof

Model 164B - Data Proof

Data Proof 164B Low Thermal Scanner is designed to allow direct comparisons of four-terminal resistance standards. With two four-terminal output lines and sixteen fourterminal channel inputs, this scanner is an ideal companion for your automatic direct-current-comparator resistance bridge or for a variety of other applications. Make fourterminal resistance comparisons simply by selecting one device on the A channel and another on the B channel. All four connections for both devices in the matrix areswitched. All other devices are left floating.

Product

Salt Spray Test Environmental Chamber

-

Guangdong Bell Experiment Equipment Co.,Ltd

Guangdong Bell Experiment Equipment Co.,Ltd

DGBell's Salt spray chamber is used to test materials likes paints, electroplating, non-organic, pastry film, anode treatment and rust prevention oil’s corrosion resistance performance. Besides, anti-corrosion treatment of various materials to make their products resistant to corrosion.

Product

Global Standard Model For 4 Point Probe Sheet Resistance Automatic Measurement System

RT-3000/RG-1000F

-

NAPSON Corp.

RT-3000/RG-1000F - NAPSON Corp.

*Fully automatic system for large sizes of flat panel with glass loading robot*Tester self-test function, Measurement position correction function, wide measurement range*Min. 0.1 mm meas. resolution and user programmable test pattern*Host (CIM) communication and 2-D/3-D Mapping software

Product

Panel-mount Type Resistivity Meter (Four-Wire Transmission, 2-channel)

HE-960RW

-

HORIBA, Ltd.

HE-960RW - HORIBA, Ltd.

HE-960RW connects resistivity sensor(ERF sereies) and measures resistivity and temperature in the sample water.This resistivity meter is ideal for such applications as the high-precision water monitoring employed at ultra-pure water plants used in semiconductor manufacturing.They utilize newly designed, high-precision, high-stability temperature measurement circuitry and a vastly improved temperature compensation function, an important element for measuring the resistivity of ultra-pure water.

Product

Multifunction Tester

M70

-

HT Italia Srl

M70 - HT Italia Srl

M70 is a mobile device dedicated to measuring Insulation resistance with test voltage up to 1000VDC and Continuity of protective and equipotential conductors with current of 200mA in private and industrial electric installations.

Product

Digital Insulation Tester

200M

-

Laxtronics Instruments & Controls Pvt. Ltd

200M - Laxtronics Instruments & Controls Pvt. Ltd

Digital insulation tester Model No: DIT200M is designed to carry out electrical insulation measurement in delicate or sensitive electronic sensors, transducers, modules and assemblies with test voltage from 1 to 30 Volts DC, its short circuit current is less than 100uA. The instrument can measure Resistance from 1 Meg Ohm to 1000 Meg Ohms.

Product

Earth Ground Tester

1625-2

-

Fluke Corporation

1625-2 - Fluke Corporation

The Fluke 1625-2 earth ground tester measures earth ground loop resistances using only clamps, only stakes, or one clamp and stakes. With the stakeless test method, the Fluke 1625-2 is able to measure earth ground loop resistances for multi-grounded systems using only current clamps. This technique eliminates the dangerous, and time consuming job of disconnecting parallel grounds, and finding suitable locations for auxiliary ground stakes.

Product

Single-Phase Transformer Winding Resistance Meters

RMO-TT Series

-

IBEKO Power AB

RMO-TT Series - IBEKO Power AB

RMO-TT series is perfect for measuring winding resistance of inductive objects such as power and distribution transformers or autotransformers. Additionally, every transformer resistance meter from RMO-TT series can analyze:tap changers,generators,electrical motors,high-current busbar joints,cable splices,and welding joints.Transformer demagnetization can also be performed with all RMO-TT instruments.The series is consisted of 3 models, with maximal test current from 40 A (RMO40TT) to 100 A (RMO100TT). RMO100TT is the only portable transformer resistance meter in the market with 100 A DC output current.The three independent channels enable testing of three windings in series. Consequently, a user can measure winding resistance in every tap position of an on-load tap changer without discharging between the tests.In addition to winding resistance measurement, a user can perform a detailed on-load tap changer analysis by analyzing recorded graphs (10 kHz sampling rate) and by measuring vibrations on an external tap changer tank.All RMO-TT instruments have a built-in tap changer control unit. Because of this, it is possible to remotely control on-load tap changer (OLTC) directly from the device. Also, a user can program DV-Win software to do everything automatically – running winding resistance tests and changing OLTC tap positions.The DV-Win software also enables control and observation of the test process, as well as saving and analyzing the results on a PC. It provides a test report, arranged in a selectable form as an Excel spreadsheet, PDF, Word, or ASCII format. Additionally, DV-Win measures and calculates the OLTC transition time, the ripple and the winding resistance for each tap changing operation. The software can also perform the calculations necessary for the “Heat Run” test.All results can be exported in the report format.

Product

Voltage Variable Attenuators

-

Pasternack Enterprises, Inc.

Pasternack Enterprises, Inc.

a High Reliability Low Noise Voltage Controlled Oscillator (VCO) which covers a 10 MHz to 20 MHzfrequency band with a voltage tuning range from 0V to 20V. This design features exceptional phase noise performance of -120dBc/Hz @ 10 kHz offset. Supply Voltage is +15V with a generated output power level of +10 dBm and 2nd harmonic output of-11 dBc typical. The assembly is RoHs compliant and available in a compact 0.5 inch SMT package with an industry standardmounting footprint. The bottom surface is copper clad with 2-5 micro inches of immersion Gold over 150 - 250 micro inchesof Electro less Nickel which makes it resistant to oxidation for ease of soldering. The VCO operates over a temperature rangeof -40°C to +85°C and is designed to meet a variety of MIL-STD-202 test conditions including Humidity, Shock, and Vibration.