-
product
Winding Resistance Meters
The NMC 'TDR' is a high precision, new generation, light weight large output current and micro-processor controlled tester. This replaces old DC wheat stone bridge and double arm bridge for measurement of DC resistance. 'TDR' adopts new advanced test current power supply technology, four terminal measurement, digital display of resistance value and test current. 'TDR' is powered by 220V AC mains single phase supply. The measurements are accurate as the test current is highly stable. High automation is achieved with automatic discharge warning.
-
product
LED Test Programmable DC Electronic Load
IT8912E Series
IT8900 series high accuracy LED specific testing electronic loads can simulate the real output of LED lights with different characteristics.Their specific circuit can realize CR-LED mode, adjustable frequency, duty ratio PWM dimming output port (frequency: 20Hz-2KHz), I-pp/I-max measurement function can test current ripple and start up surge current of LED constant flow source. Voltage and current testing speed can reach 50KHz. IT8900 series provides CR-LED / CC / CV + CC / CR /CW and other working modes, built-in USB / RS232 / GPIB communication interface. Widely used in LED driver power dimming test.
-
product
Fanless Embedded System
Axiomtek offers a full range of expandable, low power consumption/high performance vertical market targeted embedded systems (eBOX). The embedded systems are designed to operate reliably within mission critical environments. The embedded PCs are tailored to meet all your needs with useful features including powerful computing capabilities, fanless operation, wide operating temperature ranges, low power consumption, superior reliability, flexible I/O configurations, and long product life cycles and support.
-
product
1.8 - 525 MHz GrandMaster SWR Meter
MFJ-874
MFJ Grandmaster SWR/Power meters are the Cadillacs of ham radio! All GrandMaster feature peak and average, forward and reflected power readings and have selectable power ranges. Covers HF /UHF / VHF. 30, 300, 3000 Watt power ranges.
-
product
Horn Antennas
Horn antennas can be used for emissions and immunity testing. These antennas are constructed using light weight aluminum with a corrosion resistant conductive coating for indoor or outdoor use. Each antenna is individually calibrated. The calibration data and certificate will be shipped with each antenna.The high gain reduces input power requirements to generate high electromagnetic field levels for immunity testing. High gain also increases antenna sensitivity to low level signals.
-
product
3U up to 10 Slots (VPX) / 12 Slots
Designed to be beautiful, this chassis provides flexibility and ease of use to meet all the requirements by test and development engineers. With its exceedingly high-performing 1800W ATX power supply the chassis is designed for up to 120 amperes at 12 volts.
-
product
Power RC Snubbers
Single phase and Three phase availableSuitable for AC and DC voltage applicationResistance and rate power of Resistor : 1 - 50W ( can be customized to 100W or above )Voltage: 63Vac, 125Vac, 280Vac, 480Vac, 500Vac, 600VacOperating temperature : -25~+85C / -40~+105CTesting Voltage : : 1.5 x Un 10sec ( can be customized )Varistor and Diode options available. Different applications can have very different electrical and mechanical profile requirements.Please feel free to send your application details for a suggestion and quotation.
-
product
Dry Dielectric RF Coaxial Loads
4000 Series
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
product
Load Cell Transmitter
MODEL SST-LV
The SST-LV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-LV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-LV may be powered from 12-30 Vac or 10-48 Vdc. The SST-HV Has an Isolated transducer excitation out...show more -
product
RMC-8357, 2.1 GHz, 1U Rugged Rack-Mount External Controller for PXI
785673-01
2.1 GHz, 1U Rugged Rack-Mount External Controller for PXI—The RMC‑8357 is a rugged 1U rack-mount controller for PXI- or PXI Express-based systems intended for test and measurement applications requiring rack-mount controllers. It features up to two Intel Xeon eight‐core processors that support up to 32 GB of RAM. The RMC‑8357 offers hot-swappable fans, options for redundant power supplies, and support for RAID arrays, which allows multiple hard drives to be configured for high performance for mission‐critical, physically demanding applications. The RMC‑8357 meets the PXI standard’s mechanical shock and vibration specifications and functions over wide operating ranges.
-
product
Omnidirectional Sound Source
DS3
The Dodecahedron Speaker Set offers a lightweight, yet powerful signal source for room & building acoustic measurements. The optimized frequency response ensures precise measurements in accordance with the ISO 16283 and the ISO 3382 standards. The set includes the robust omnidirectional DS3 odecahedron Speaker and the remote-controlled PA3 Power Amplifier. Equalized acoustic frequency spectrum from 100 Hz to 8 kHz.
-
product
USB-8502, 2-Port, High-Speed/FD, USB CAN Interface Device
784662-01
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN fram...show more -
product
Power Supplies
Our short-circuit-proof, single or triple-phase power supplies for automation are approved according to CE/TÜV, UL and CCC. Different voltages of 12 V, 24 V and 48 V can be selected. The most important features: top-hat rail assembly, status display, regulatable output voltage, parallel connection, ready and alarm output. Output power of 18 to 960 W. Protection class IP20.
-
product
Portable Three-Phase Phantom Load
EE-120A-3 + EE-500V-3
The Phantom Load is able to generate three-phase voltages and currents with unprecedented stability and measurement accuracy. The amplitude and phase-shift of each current and voltage is individually adjustable. The generated values of voltage, current, power, power factor, phase shift, THD and frequency are indicated on the LCD display.
-
product
Test Adapter / Extender
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly.
-
product
Non-RMS Responding Power Detectors
Recognized as the pioneer and leader in RF detectors, Analog Devices offers a broad portfolio of high performance logarithmic amplifiers and TruPwr™ rms detectors. ADI logarithmic amplifiers measure signals up to 100 dB dynamic range, from dc to microwave, and accuracies of ±0.2 dB, and are well-suited for both RSSI and transmit power level detection. The TruPwr rms detectors address the challenge of measuring complex waveforms found in spread spectrum CDMA/W-CDMA and higher order QAM modulation systems and provide an accurately scaled dc voltage, which is the rms equivalent of the input waveform.
-
product
Sensor Tester
QST-5
The QST-5 device is intended for testing many popular sensors used in the automotive industry. The tester powers the tested sensors by itself, so it can be used both in a vehicle and outside of it.
-
product
Multichannel Recorder-Analyzer
Portable measuring complex for control, registration and analysis of parameters of electrical devices of the subway and railway.The measuring unit of the portable recorder of electrical devices is based on the measuring equipment of the NI CompactRIO platform manufactured by National Instruments (USA, www.ni.com ), which is placed in a special case for transporting the Pelican-Storm iM2450 with an instrument front panel and connectors for connecting a source (s ) power supply, user's workstation computer and sources of measured voltage current signals.
-
product
2U Rackmount Chassis For ATX/Micro ATX/Mini-ITX Motherboard
AX61223TM
*Supports ATX/Micro ATX/Mini-ITX motherboard*Supports ATX power supply*Internal one 3.5" HDD drive bays*Front-accessible one 3.5", one 5.25" HDD drive bays and one slim CD-ROM bay
-
product
PHIL System (Power Hardware In-Loop System) Case Study
In the PHIL (Power Hardware In-Loop) Case Study, the PHIL system consists of a PONOVO 4-Q amplifier, RTDS simulator, DC electronic load unit and PV inverter.
-
product
PXI Single 8x2 1-Pole 10A Power Matrix
40-551-002
Used for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. X and Y connections are made via a 20-way GMCT plug, the 8x4 module with loop-thru has an additional 20-way GMCT plug for module-to-module connection. Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. Suitable for applications requiring switching of either mains voltage or direct current.
-
product
High-Performance Autoranging DC Power Module, 60V, 17A, 500W
N6756A
The Keysight N6756A is a 500 W high-performance, autoranging DC power module that provides low noise, high accuracy and programming speeds that are up to 10 to 50 times faster than other programmable power supplies. Optional high-speed test extension offers an oscilloscope-like digitizer that increases measurement accuracy when viewing high-speed transient or pulse events within the device-under-test (DUT).
-
product
Electronic Loads
T3EL Series
The T3EL series is a family of single channel, 200 & 300 Watt Electronic Loads that are ideal for R&D, product validation and Q&A in a bench or automated environment for low to medium power applications starting from 60mA, such as electronic components, batteries, portable chargers and power products. Electronic Loads are typically used to provide a load to the outputs of a power supply, usually capable of dynamic loading, and are fully programmable. Electronic Loads help designers to test electronic power products and ensure quality, reliability, and performance.
-
product
NI-5741, 16-Bit, 1 MS/s, 16-Channel Signal Generator Adapter Module for FlexRIO
782864-01
The NI‑5741 provides simultaneously sampled analog output channels for signal generation. It also features single-ended, DC-coupled inputs and general-purpose digital input and output lines for system stimulus and control. The NI‑5741 is ideal for applications requiring high-channel density and the power of a user-programmable FPGA. Each channel has a user-configurable sample rate, and data is written directly from the FPGA. To use the NI‑5741, you must pair it with a compatible PXI FPGA Module for FlexRIO.
-
product
Global Data Center Platform
Cyxtera
Centralize your complete data ecosystem through a software-defined platform that offers on-demand provisioning and customization of each of the elements of a traditional data center - including storage, compute power, networking and management.
-
product
2-Port 9 GHz Analyzer
SC5090
The SC5090 is a 2-port 9.0 GHz Vector Network Analyzer featuring excellent dynamic range, fast measurement speed and a high output power, in a compact package, with the maximum standard software feature set.
-
product
Smart Meters
WISE-M500 Series
WISE-M500 series power meters are easy to use, cost effective smart meters, that provide high accuracy measurement, display and communication (Modbus/RTU). Characterized by a compact size, and flexible connection (1P2W, 1P3W, 3P3W), the WISE-M500 series are ideal for energy monitoring.
-
product
Palm-top DC Power Supply
R4K-36 Series
R4K-36 series is the most compact power supply among the family of ultra compact bench-top DC supply, RK series. In addition to its impressive compact size, 4-digit voltage and current meters make circuit testing easier. With capability of digital interface, it is also ideal for production line of electrical components and for quality inspection. R4K-36 is an innovative power supply, and more than just an ordinary DC regulated supply.
-
product
Non-Contact Voltage Tester
NCVT-1
Non-contact detection of voltage in cables, cords, circuit breakers, lighting fixtures, switches, outlets, and wires.High intensity, bright green LED indicates the tester is operational and aids in illuminating the workspace.When voltage is detected, a high intensity, bright red LED illuminates and a warning tone sounds.Discrete digitally controlled ON/OFF power button.Auto power-off feature conserves and extends battery life.Microprocessor controlled low-battery indicator and tester shutdown.CAT IV 1000 Volt safety rating provides expanded operation and protection.
-
product
Power Modules
VadaTech offers high density AC or DC input power modules with up to 95% power efficiency in single module and double module variants to accommodate different power needs. We also offer specialty modules such as extended full, block format for specific chassis types.