Showing results: 61 - 75 of 99 items found.
-
DYNOmite Dynamometer
Standard on-board kits include: wireless electronic torque transducer-equipped driveshaft yoke, tail-shaft pickup coil, wireless interface module, DYNOmite handheld data-acquisition computer, AC power supply, data wiring harness, and protective carrying case.
-
ProDAQ 3202 -
Bustec Ltd.
The ProDAQ 3202 voltage reference card is used in the ProDAQ 3180 ultra-performance motherboards and LXI function card carriers. The ProDAQ 3202 voltage reference card is plugged directly onto the motherboard or carrier and can distribute the reference voltage to all ProDAQ function cards via two signal lines. This allows the distribution as a differential signal to overcome possible noise pick-up.
-
VMA -
North Atlantic Industries
NAI’s VMA is a field-adjustable, AC-Powered, AC Voltage Monitor used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits.High and low voltage limits, and "pick-up" and "drop-out" time delay are field-adjustable. The VMA voltage monitor is ideally suited for rugged defense and industrial applications.
-
595 -
Electronic Specialties Inc.
The #595 is a premier automotive diagnostic tool. It is equipped with the latest testing capabilities, including Milliseconds Pulse Width, for measuring the on-time of fuel injectors. The #595 features a huge LCD display w/bargraph for easy viewing. This meter can even be interfaced to your PC or notebook computer for enhanced diagnostics and data presentation. The software and computer interface cable are included free! The #595 includes two sets of test leads, RPM pick-up, temperature probe, software CD, interface cable, protective holster, 9 volt battery, instructions manual and hard storage case. Inductive RPM pick-up features a five position, adjustable sensitivity switch.
-
SA420 -
Electro-Sensors, Inc.
Features • Works with a remote / external pulse frequency output sensor (NPN, PNP, or Mag Pick-up) • Accepts wide range of input frequencies 0.01 Hz to 10 kHz • 4-20 mA and 0-10 VDC outputs proportional to shaft speed • Field adjustable calibration • 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options • DIN rail mount
-
1031-C3, 1031-C6 -
The Eastern Specialty Company
More than just an indicator, TESCO’s KYZ Indicator and Tester Cat. 1031-C3 (3-wire) and 1031-C6 (6-wire) can also be used to perform accuracy testing of KYZ pulses on all TESCO Next Generation Test Equipment. TESCO’s KYZ Indicator and Testers can be used as a pulse input using the same pickup connection on the front panel of all TESCO Next Generation Test Equipment.
-
328 -
Electronic Specialties Inc.
*Versatile instrument can measure RPM on a wide variety of engines from string trimmers to automotive. *Reads engine revolutions from 0 to 20,000 RPM *Picks up RPM signal wireless or with supplied inductive pickup *Great for setting idle speeds! *Built-in LED Flashlight which can be used while taking measurements *Backlit LCD display *Accuracy +10 RPM
-
Extech 461950 -
Extech Instruments Corporation
The 461950 is a 1/8 DIN Panel Tachometer. Measure rotational motor speed, moving fans, pumps, gears, propeller devices. Choice of 2 sensor pickup types: Proximity sensor-0.1 in. (3 mm) target distance, range up to 36,000rpm (600Hz); Photoelectric sensor-0.4 in. (10 mm) target distance, range up to 6,000rpm (100Hz). 1/8 DIN size. Powered by 115/230VAC 50/60Hz.
-
MTR110 -
Rhopoint Metrology Ltd
The Surfmatic MTR110 is a pocket sized surface roughness measuring instrument ideally suited to rapid on-the-spot surface measurements. Conforms to ISO Class 3.Features• Back-light LCD• Dynamic Test Display: progress of cut-off length during testing• Li-ion rechargeable batteries• Protection slide on pick-up• Auto-off after 90 seconds• Pocket-size and economically priced• Both Ra and Rz parameters in one instrument• Features external calibration specimen• Large measuring range suitable for most materials• Piezo-electric pick-up stylus for external surfaces• Includes steel test piece• Includes charger unit• Measurements of shafts above 40mm diameter using the Vee groove in base
-
CH-6130/6140 -
Ono Sokki
The CH-6130/6140 charge converter is a simplified type of charge amplifier converting charge signal to voltage.It can be connected directly to an input BNC connector of a CCLD applicable equipment such as FFT analyzer or vibration comparator, enabling direct connection of a charge output pickup without suing a box type amplifier.
-
DynTek-PC -
Taylor Dynamometer, Inc.
The DynTek-PC for engine dynamometers is a display-only system intended for basic engine dynamometer testing requirements. This system provides for the measurement of torque in either tension or compression (both clockwise and counter-clockwise engine rotation) and speed from a standard Magnetic Pickup. The system is designed to set on a table or desktop near the PC.
-
DYNOmite Dynamometer
Truck chassis kit includes: heavy-duty tube-steel frame and 30"-diameter "dually" wide-roll assembly with machined-in "traction grooves," air brakes, diamond-tread deck plate, floor anchors, wheel chocks, vehicle tie downs, eddy-current absorber and controller with overdrive, S-beam load cell, DYNOmite-Pro data-acquisition computer, inductive RPM pickup, DYNO-MAX software, electronic auto-load control, 28-channel data harness, engine-temperature thermistor, and more.
-
Model 273 HP -
Kusam Electrical Industries Limited
The 273 HP is a Non-contact voltage detector. It has two ranges for selection.The 273 HP consists of an internal pickup sensor, a function selection switch, a visual and a sound annunciator. With the 273 HP, physical contact with electrical conductors is not necessary when testing for live lines. Its sensor senses the radiated field which surrounds live conductors. Radiated field strength increases with voltage and decreases quickly with distance or earth shielding
-
EMAG Technologies Inc..
NeoScan® is a unique electric field measurement system with unprecedented innovative features. NeoScan systems utilize EMAG’s patented, electro-optic (EO) field probe technology. Unlike conventional near-field scanning systems that require metallic pickup radiators or sensors, NeoScan probes are made of absolutely metal-free parts.
-
MetrologyWorks, Inc.
Single Piece Aluminum InsertWe have assembled this SMR in a way that the insert will not come out. When you drop the competitions SMR they shift or pop out after a few short drops. With our Rhino Series SMR, Drop, Pickup, and Measure on. You get the performance of a solid SMR that is much more affordable. These are available in High Accuracy SMR versions. We keep the Rhino Series SMR s in stock at all times.