Showing results: 796 - 810 of 1119 items found.
-
16197A -
Keysight Technologies
The 16197A is designed for impedance evaluations of bottom electrode SMDs. It achieves stable frequency characteristics up to 3 GHz and provides highly repeatable measurements. The Keysight 16197A supports various SMD sizes, as small as 1005 (mm)/0402 (inch) and as large as 3225 (mm)/1210 (inch). Accommodation of the 0603 (mm)/0201 (inch) size is available with option 001.
-
E5061B -
Keysight Technologies
Select the best configuration for your test needs from a wide variety of test set options: 100 kHz to 1.5 GHz/ 3 GHz, 2-port, 50 or 75 ohm, transmission/reflection or S-parameter test set Address a broad range of applications with the LF-RF option (Option 3L5/3L4/3L3): 5 Hz to 3 GHz, 2-port, 50 ohm, S-parameter test set, gain-phase test port, built-in DC bias source Combine network analysis and impedance analysis to customize your application in a single instrument (Option3L5/3L4/3L3 plus 005) Every spec verified, adjustments included Lock in support & peak performance from the start
-
Pasternack Enterprises, Inc.
Pasternack 3.5mm connector category has several part numbers, most of which are RoHS and REACH compliant. 3.5mm connector series in this category will terminate to coax. Pasternack 3.5mm connectors are built to precise RF and microwave industry specifications. 3.5mm connector items are manufactured in male or female gender with 50 Ohm impedance. 3.5 mm connector products are available in bulkhead or no mount options. These 3.5mm connectors include clamp/solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 3.5mm connector series is in-stock. Not only in stock, but these 3.5mm connectors will also ship the same day as they are purchased.
-
Pasternack Enterprises, Inc.
Pasternack SHV connectors category has several part numbers, most are RoHS and REACH compliant. SHV connector series in this category will terminate to coax or terminal. These SHV connectors are built to precise microwave and RF industry specifications. SHV connector items are built in jack or plug gender with 50 Ohm impedance. Connectors in SHV series are available in bulkhead, 4 hole panel or mountless options. These SHV connector designs include clamp/solder, crimp/solder or solder attachment methods. As with other over 40,000 RF, microwave and millimeter wave Pasternack products, this SHV connector series is in-stock. Not just are they in stock, but these radio frequency connectors will ship the same day as they are purchased.
-
TX2001 -
BI Communications
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3000m (10,000ft) 50, 75 & 100 ohm Selectable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
Pickering Interfaces Ltd.
Pickering's LXI high frequency (HF) matrix modules are suitable for switching frequencies up to 50MHz. They have an impedance of 50 and uses SMB signal connectors or with a larger case size is uses BNC connectors. This HF matrix is designed to provide a simple and scalable bidirectional matrix for radio frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems.
-
DiagnoSYS Systems Ltd
The compact and portable Faultfinder VIP system, combined with a Laptop running TestVue software, provides a way to rapidly identify failures by troubleshooting a PCB or CCA. It uses impedance signatures (also known as VI testing) measured from a known working circuit and stores them as a test program. These stored signatures are then compared to the ones being measured on the suspect circuit to automatically determine if there is a fault.
-
MPI-520S -
Sonel S.A.
The MPI-520S multifunction meter is dedicated to perform diagnosis of electrical installation according to IEC 61557 standards. Digital meter MPI-520S is designed to measure impedance of a short cicuit loop also without triggering RCD, parameters of RCD, insulation resistance, earthing resistance, continuity and also for phase sequence testing. Furthermore to measure and logging of AC voltage and current, frequency and power.
-
MKS Instruments
MKS RF Power Generators provide reliable solid state power for thin films processing equipment. They are vital components of semiconductor fabrication systems, which produce the integrated circuits (ICs) or chips required by modern computers and electronic equipment. MKS RF Generators, combined with our Impedance Matching Network and our V/I Probe form a complete RF Delivery System.
-
VE2729XAU -
Vasavi Electronics
Its a Microprocessor Based 200KHz Automatic Transformer Tester with inbuilt 20 Pin Channel Scanner for Automatic Switching and Testing Coils & Transformers (Ferrite) with Max. 20 PINS. Test Parameters : -> Inductance (L)-> Leakage Inductance (Lk)-> Capacitance (C)-> DC Resistance (Rdc)-> AC Resistance (Rac)-> Turns Ratio with Winding Polaity-> Quality Factor (Q)-> Impedance (Z)
-
Texas Instruments
Ultrasonic sensing is the measurement of the time between an ultrasonic signal being sent and received. The interval between these two signals is typically referred to as time-of-flight (ToF) and depends on the distance the ultrasonic wave travels until it is reflected due to an impedance change and the speed of the ultrasonic wave. The basic equation time = distance / speed can be used to measure fluid level, fluid identification/concentration, flow, or proximity.
-
NovaCarts Battery -
MicroNova AG
Exact cell simulation for validating battery management systems (BMS). "NovaCarts Battery" represents one of the most powerful and precise cell simulation systems on the market. This is leveraged by the modular and scalable HiL system to create optimum conditions for developing new battery management functions such as state-of-charge (SoC) and state-of-health (SoH) controls, active cell balancing and electrochemical impedance spectroscopy.
-
40-784-142 -
Pickering Interfaces Ltd.
Pickering Interfaces’ 40-784 PXI Microwave Multiplexer Modules have a characteristic impedance of 50 Ohm and are capable of switching signals up to 40GHz. Available in single or dual SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
40-784-101 -
Pickering Interfaces Ltd.
Pickering Interfaces’ 40-784 PXI Microwave Multiplexer Modules have a characteristic impedance of 50 Ohm and are capable of switching signals up to 40GHz. Available in single or dual SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
40-784-001 -
Pickering Interfaces Ltd.
Pickering Interfaces’ 40-784 PXI Microwave Multiplexer Modules have a characteristic impedance of 50 Ohm and are capable of switching signals up to 40GHz. Available in single or dual SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
