Showing results: 316 - 330 of 1119 items found.
-
SIM911 -
Stanford Research Systems, Inc.
The SIM910 and SIM911 are low-noise, programmable preamplifiers which are ideal for a wide range of small signal applications. The primary differences between the two models are their input impedance and input noise.
-
WCA Series -
WanTcom Inc.
WCA series super low noise amplifiers have sub-0.5 dB noise figure at VHF band with several octave bandwidth. The amplifiers have 75 Ohm impedance.
-
Kontron
Hartmann’s cPCI 3U RB Series Backplanes utilize a board design based on the HIGH-SPEED DESIGN concept. Low reflection is achieved by means of uniform signal surge impedance.
-
42090A -
Keysight Technologies
The 42090A is an open termination and is primarily used for performance tests of Keysight's 4-terminal pair LCR meters and impedance analyzers. Refer to the instrument's operation/service manual for the method of using this standard.
-
Ametek Scientific Instruments
Simultaneous Electrochemical Impedance Spectroscopy (EIS) tests can be run on multiple cells by connecting Solartron 1455A/1451A series frequency response analyzer (FRA) modules to the 1470E. These FRAs can operate in single sine correlation or multi-sine / Fast Fourier Transform (FFT) analysis mode, providing the ultimate in speed, precision and accuracy. The 1455A FRA provides high performance impedance measurements over the frequency range 10 μHz to 1 MHz, while the 1451A FRA operates from 10 μHz to 100 kHz.
-
PeakTech Prüf- und Messtechnik GmbH
A type of electronic test equipment used to measure the inductance (L), capacitance (C), and resistance (R) of an electronic component.[1] In the simpler versions of this instrument the impedance was measured internally and converted for display to the corresponding capacitance or inductance value. Readings should be reasonably accurate if the capacitor or inductor device under test does not have a significant resistive component of impedance. More advanced designs measure true inductance or capacitance, as well as the equivalent series resistance of capacitors and the Q factor of inductive components.
-
Tektronix, Inc.
A low voltage single-ended probe is typically used for measuring high-speed, ground referenced signals up to 12 V. These low voltage probes are the best choice for making measurements on high impedance, high frequency circuit elements which require minimal probe loading. Users should select probes with a low input capacitance specification (~1 pF) to minimize the probe’s loading effect on the circuit. A probe with lower input capacitance will offer higher input impedance at higher frequencies.
-
SARK-110 -
Seeed Technology Inc.
The SARK-110 is a completely new design concept for an Antenna Analyzer. This is a truly pocket size device, so you can take it anywhere. It offers a gorgeous 3” high-resolution, active-matrix color display that allows information-rich diagrams. The user interface has been designed to be intuitive and easy to use. On screen menus provide user guidance and the operation is mainly controlled by the two navigation keys. The graphical impedance displays provide a quick view of the antenna impedance characteristics on a user selected frequency range.
-
610102117 -
Virginia Panel Corporation
The 20 GHz coax contacts have an impedance of 50 Ohms and a current rating of 5 amps. It is recommended to use SF142 to achieve 20 GHz and RG223 to achieve 12 GHz.
-
DP-25 -
PINTEK Electronics
*Econmical High Voltage Model*25MHz/1400Vp-p Max.*3 Range: x20/ x50/ x200*Input Impedance 4MΩ//1.2PF*Separating Design(Standard No.114205) Convenient & Durable.
-
SS1061A -
Sanshine Electronis Co., Ltd.
LCZ LCR meters are a high-grade component test instrument upgraded from SS106X series, with 4 output impedance modes and measuring results compatible with other well-known LCR meters.
-
SS1062A -
Sanshine Electronis Co., Ltd.
LCZ LCR meters are a high-grade component test instrument upgraded from SS106X series, with 4 output impedance modes and measuring results compatible with other well-known LCR meters.
-
AMPI-520 -
Amperis sl
The AMPI-520 digital meter is designed to measure impedance in short-circuit loops without tripping the differential protection, it also measures the protection tare, earth resistance, continuity and phase sequence check.
-
NG 600 -
Unaohm Start S.r.l.
The NG 500 noise generator is an external module with dual power supply for different applications: to calibrate filters, switchboards, to the distance of a fault caused by the impedance mismatch, to test the cable efficiency.
-
2523 -
Shenzhen Chuangxin Instruments Co., Ltd.
With Chuangxin’s experience in impedance test and marketing survey, the new battery tester-TH2523 is successfully launched. It can be competitive with other similar products with its outstanding performance, easy operation and new look.