PXI Chassis
See Also: Chassis, 3U PXI Chassis, 6U PXI Chassis, Portable PXI Chassis, ATE
-
product
Chassis - 16x16 Non-Blocking, Full Fan-Out Matrix for 50 ohm Signals from 1 GHx to 2.7 GHz
CXS/16x16-50-MF
This Chassis is a 16x16 non-blocking, full fan-out matrix for 50 ohm signals from 1 GHz to 2.7 GHz. The system uses splitters and amplifiers on the input side and switch modules on the output side to form a stubless matrix. Unit comes standard with LAN, GPIB and RS232 control. A keypad manual control is optional.
-
product
Quiet Safety 4U Rack Mounted Industrial Chassis With 14-Slot Backplane And Motherboard
RK-620 Series
- EIA RS-310C 19” rack mount standard- Supports 14-slot backplane and ATX motherboard- Two 5.25” external, one 3.5” external and one 3.5” internal drive bay- Two USB ports inside front I/O- Replaceable, easy-to-clean air filter- PS2 ATX power supply- Low noise 12cm PWM controlled (103 CFM)
-
product
6-slot PXIe Chassis
PXCe4006
6-slot PXI Express chassis1 system slot, 1 PXI Express slot and4 PXI/PXI Express full hybrid peripheral slotsOptional: complex FPGA trigger controller with8 freely configurable trigger IOs on the rear sideVery compact 1U 19" designFour link PXI Express chassisEasily replaceable fan unit
-
product
NI-9147, 4-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis
783496-01
4-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis - The NI‑9147 is a rugged Ethernet chassis that you can use to add C Series I/O modules to any standard Ethernet network. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. With the NI‑9147, you can add high-performance I/O to your PC-based application or expand your CompactRIO, PXI, or industrial controller application.
-
product
4U 5-Slot CompactPCI® Chassis with Redundant Power Supplies
cPCIS-6400U Series
The cPCIS-6400U/6400X Series subsystems are designed for 6U cPCI boards with 80mm RTMs. The chassis is 4U in height and standard 19" rack mount width.
-
product
Chassis - up to Twelve 8x1 or 4x2 Modules & up to Six 8k Modules
HXV/96-MF
These Chassis controls up to 12 8x1 modules, 12 4x2 modules, or up to 6 of the 8K modules in almost any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules, Driver Modules and a Control Module to complete the system.
-
product
CompactPCI Chassis 3 Slots
1U 84HP
Hartmann CompactPCI 1U system platform provides an intelligent, practical packaging solution for high-performance processors. The full width rack mount model provides a 3 slot 5V I/O 3U cPCI backplane for horizontal mounting of boards. This system is designed with enhanced EMC features.
-
-
product
6-Slot LXI/USB Modular Chassis
60-106-001
Pickering Interfaces’ 60-106-001 modular LXI/USB chassis occupies only a small, 1U rack-height form factor, making it suitable for portable and space-restricted rack-mount applications. The chassis features remote control via USB or LXI Ethernet. Remote control over a network enables the switching function of a test system to be located as close as possible to the target equipment.This chassis is also available with built-in scan list sequencing and triggering (model 60-106-002).
-
product
Economical 4U Rack Mounted Industrial Chassis Supports ATX Industrial Motherboard
RK-620MB-L Series
- Supports ATX industrial motherboards- Two external 5.25'' drive bays- Two USB type A connectors on front panel- 12cm two ball bearing cooling fan ( 103 CFM)- PS2 ATX power supply
-
product
CompactPCI Chassis 8 Slots
3U/84HP
Hartmann CompactPCI 3U system platform provides an intelligent, practical packaging solution for high-performance processors. The full width rack mount model provides an 8 slot 3.3V or 5V I/O 3U cPCI backplane for vertical mounting of boards.
-
product
Chassis 8 Slot
PXIe 4U/ 42HP
As PXI has evolved into high-speed serial fabric technology, so has the Hartmann Electronic product line with the addition of its PXIe solutions. More power, more bandwidth, more functionality.
-
product
PXI 8 Slot BRIC 138x8 1-Pole Dual Analog Bus (3 sub-cards)
40-560A-121-138X8-M
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
NI-9149, 8-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis
783376-02
8-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis - The NI‑9149 is a rugged Ethernet chassis that you can use to add C Series I/O modules to any standard Ethernet network. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. With the NI‑9149, you can add high-performance I/O to your PC-based application or expand your CompactRIO, PXI, or industrial controller application.
-
product
Wallmount Industrial Chassis Supports 10-Slot Backplane
RK-609B
- Supports 10 slot PICMG backplane- Two 5.25" and two 3.5" external drive bays, one internal 3.5" drive bay- Upper cover with captive screw- Drive bay with shock and vibration resistant design- Replaceable and easy-to-clean air filter- 12cm cooling fan (85CFM)- Two USB and one PS/2 keyboard connectors on front panel
-
product
Compact PCI-Express/PXI-Express Module
ACE1553-3U-x
The ACE1553-3U-x is a member of AIM’s new family of compact PCI-Express/PXI-Express modules for analyzing, simulating, monitoring and testing
-
product
NI-9145, 8-Slot, Zynq-7020 FPGA, EtherCAT CompactRIO Chassis
784756-01
8-Slot, Zynq-7020 FPGA, EtherCAT CompactRIO Chassis - The NI‑9145 is a rugged EtherCAT slave chassis for adding deterministic, distributed I/O to any CompactRIO, PXI, or industrial controller with two Ethernet ports. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. You can daisy chain multiple NI‑9145 slave chassis from the master controller to expand time-critical applications to higher channel counts while maintaining hard determinism with minimal processor resources.
-
product
PXI Solid State Matrix Module, 8x2, 30 A, Hardware Interlock
40-555B-011-HI
The 40-555B-011-HI is a high current 8x2 matrix with hardware interlock occupying two slots of PXI chassis. Each matrix crosspoint uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
product
Four Slot PXI/PXIe Full Hybrid ABex Chassis with up to PXIe x4 Connectivity on Each Slot
ABex PXIe Rack 04
Ultra-Compact 2U ABex chassis with 4 slots. This variant is characterized by outstanding compactness and due to the directly integrated PXIe full hybrid backplane one achieves maximum performance at an attractive price. The first slot is reserved for a single slot PXIe controller. Either Konrad PXIe embedded controllers or MXI interfaces are supported.
-
product
Chassis Remote Control Cable
The Chassis Remote Control Cable connects the PXI Remote Control Module to a variety of host interfaces on desktop PCs, rack-mount controllers, laptops, or other PXI or PXI Express systems.PXI Remote Control Modules support either copper cabling or fiber-optic cabling, and some models support both. Copper cables offer higher data throughput capability but are generally shorter (1 meter to 10 meters), while fiber-optic cables are available in much longer options (100 meters or more) but may have lower data throughput capability.
-
product
8-Slot Fully Hybrid PXIe Chassis
42-924-001
Our 42-924 PXIe Chassis provides seven hybrid compatible slots for application flexibility. The chassis utilizes a single PCI segment with a dedicated PCIe-to-PCI bridge module for the hybrid slots. The PXI specific high accuracy clocks and trigger signals are generated and controlled by an independent clock module attached to the rear of the backplane. This hybrid chassis supports the latest generation (Gen 3) PXIe modules. The chassis is fitted with a 400W industrial grade power supply mounted at the rear of the unit with sufficient capacity to support PXI modules with very high current demands.
-
product
CXM Custom Chassis
Cytec can manufacture custom microwave systems to your specifications. Need to build a switch with 6 different styles of relays? Want to combine relays, amps, splitters and couplers? Need to combine parts from 8 different vendors to meet the specs you want?
-
product
CompactPCI Chassis 4 Slots
2U 84HP
Hartmann CompactPCI 2U system platform provides an intelligent, practical packaging solution for high-performance processors. The full width rack mount model provides a 4 slot 5V I/O 9U monolithic (6U cPCI) backplane for horizontal mounting of boards.
-
product
Wallmount Industrial Chassis for ATX Industrial Motherboard
RK-608MB-C / IMB-M40H
ADLINK's rackmount and wallmount industrial chassis are aligned with integrated subsystem design, service and performance, is optimized for combined motion/vision/IO applications.
-
product
Chassis - Control up to 16 Modules with as Many as 32 Two Pole Relays Per Module Allowing 1xN Multiplexers up to 1020x1, 2 Pole Muxes up to 512x1 or 2xN Matrix Configurations up to 256x2
JX/256-MF
These Chassis control up to 16 modules with as many as 32 two pole relays per module allowing 1xN multiplexers up to 1020x1, 2 pole muxes up to 512x1 or 2xN matrix configurations up to 256x2. Jumpering option allow the modules to be controlled as separate smaller muxes, i.e. 64 4x1 2 pole muxes, or combine specific groups to allow an almost unlimited combination of sizes. Add a Control Module and optional manual control to complete the system.
-
product
NI-9146, 4-Slot, Spartan-6 LX45 FPGA, Ethernet CompactRIO Chassis
782445-01
4-Slot, Spartan-6 LX45 FPGA, Ethernet CompactRIO Chassis - The NI-9146 is a rugged Ethernet chassis that you can use to add C Series I/O modules to any standard Ethernet network. You can program the chassis using scan-mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. The NI-9146 enables you to add high-performance I/O to your PC-based application or expand your CompactRIO, PXI, or industrial controller application.
-
product
Economical Desktop/Wall-Mount Chassis With Front I/O Interfaces For ATX Industrial Motherboard
RK-500MB-L
- Front I/O Interface and seven PCIe expansion slots for add-on cards- Supports industrial ATX motherboard- One 5.25'' external and two 3.5'' internal- Flex ATX power supply- 12 cm two ball bearing cooling fan ( 103 CFM)
-
product
Eight Slot PCI-PXIe Full Hybrid ABex Chassis with up to PXIe x4 Connectivity on Each Slot
ABex PXIe Rack 08
Compact 4U ABex chassis with 8 slots. This variant is dedicated for cost sensitive applications that require more than three PXIe/PXI peripheral slots. It features am eight slot PXIe full hybrid backplane to guarantee maximum performance at an attractive price. The first slot is reserved for a single slot PXIe controller. Either Konrad PXIe embedded controllers or MXI interfaces are supported.
-
product
Chassis 6 Slot
PXIe 1U/ 84HP
This versatile slim-box style chassis comes standard with 1 system slot, 1 PXI Express slot, and 4 PXI/PXIe full-hybrid peripheral slots, all in accordance with PXI-5 PXI Express Hardware Specification Rev 1.1.
-
product
FPGA PXI Card
GX3601
The GX3601 is a 3U PXI FPGA card with 80, TTL buffered channels. The card is comprised of a GX3501 80 channel, TTL buffer expansion module and a GX3500 FPGA card.
