Showing product results. 1 - 15 of 66 products found.
-
RS Series - Cytec Corp.
The RS Series of computer controlled switching systems are designed to switch multiwire groupsof signals on standard D9, D15 or D25 connectors. These systems are typically used for signalssuch as parallel TTL, RS232, RS422, WAN or Modems, but they can also be used for any group ofanalog or digital signals having a bandpass below 30 MHz or data rate below 20 Mbps. A modular design concept is used that provides configuration flexibility by allowing different controlmodules, switch modules and display modules to be assembled in one chassis.LED displays and switch point Status Feedback are available on all systems. Computer controlvia 10/100 Ethernet LAN ( TCP ), IEEE488 (GPIB) and RS232 is standard, while USB, andmanual controls are optionally available.
-
CXS 50 Ohm RF Or 75 Ohm - Cytec Corp.
These switch modules use high reliability solid state switches for 50 or 75 ohm applications between 10 KHz and 2.75 GHz. Fast, inexpensive solid state relays are perfect for coaxial switching at low power RF and CATV frequencies. Switch times as fast as 25 us and life expectancy of 100 billion operations. Terminated to 50 or 75 ohms in both directions for use with splitters in either direction.
-
RSM/128-MF - Cytec Corp.
These Chassis controls up to 16 8x1 modules, 32 4x1 modules or any combination or configuration such as a 16x8 matrix, 32x4 matrix or two 16x4 matrices. Matrix configurations are non-blocking and physical layer switches act like a cable connection with D connectors creating a one to one connection between D9, D15 or D25 connectors. All wires are switched as a group on each connector for easy programming. LEDs on the front panel show switch and power status. Add Switch Modules, Driver Modules and a Control Module to complete the system.
-
CXM/128-MF - Cytec Corp.
These Chassis controls up to 16 8x1 modules, 32 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 128 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional. Chassis is available with sink or source relay drivers from + 5 to + 28 volts, ot TTL drivers for programmable attenuators. Firmware commands for Fade and Handover for WiFi, Cell Phone and WiMax labs. Fully custom systems built with little to no NRE.
-
CXAR/64-MF - Cytec Corp.
These Chassis controls up to 16 4x1 modules, or mixtures of 4x1's, 2x1's and 2x2 modules in any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules, CP8 Driver Modules and a Control Module to complete the system. Pushwheel manual control is optional.
-
HXV/32-MF - Cytec Corp.
These Chassis controls up to 4 8x1 modules, 4 4x2 modules, or up to 2 of the 8K modules in almost any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules, Driver Modules and a Control Module to complete the system.
-
CXAR/16-MF - Cytec Corp.
These Chassis controls up to two 8x1 modules, four 4x1 modules or mixtures of 8x1's, 4x1's, 2x1's and 2x2 modules in any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules and a Control Module to complete the system. Pushbutton Manual control is optional.
-
CXM/64-MF - Cytec Corp.
These Chassis controls up to 8 8x1 modules, 16 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 64 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional.
-
CXAR/32-MF - Cytec Corp.
These Chassis controls up to four 8x1 modules, eight 4x1 modules or mixtures of 8x1's, 4x1's, 2x1's and 2x2 modules in any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules and a Control Module to complete the system. Pushbutton manual control is optional.
-
CXS/16x16-50-MF - Cytec Corp.
This Chassis is a 16x16 non-blocking, full fan-out matrix for 50 ohm signals from 1 GHz to 2.7 GHz. The system uses splitters and amplifiers on the input side and switch modules on the output side to form a stubless matrix. Unit comes standard with LAN, GPIB and RS232 control. A keypad manual control is optional.
-
RS/16 - Cytec Corp.
These Chassis controls up to 16 switch modules with 9 to 25 wires switched per module. They are basically used to make a 9 to 25 wire 1x16 mux with D9, D15 or D25 connectors. LEDs on the front panel show switch and power status. Add up to 16 Switch Modules and a Control Module to complete the system. Push button manual control on the front panel is optional.
-
CXAR/128-MF - Cytec Corp.
These Chassis controls up to sixteen 8x1 modules, thirty two 4x1 modules or any combination or configuration of 8x1's, 4x1's, 2x1's and 2x2 modules. LEDs on the front panel show switch and power status. Add Switch Modules, CP8 Driver Modules and a Control Module to complete the system. Keypad Manual manual control with LCD display is optional.
-
CXM/256-MF - Cytec Corp.
These Chassis are typically used to control relays greater than 8x1 or control multiple relays in series forming larger switches than normally possible such as 16x1 to 32x1 sections. Or control mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 256 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional.
-
JX/256-MF - Cytec Corp.
These Chassis control up to 16 modules with as many as 32 two pole relays per module allowing 1xN multiplexers up to 1020x1, 2 pole muxes up to 512x1 or 2xN matrix configurations up to 256x2. Jumpering option allow the modules to be controlled as separate smaller muxes, i.e. 64 4x1 2 pole muxes, or combine specific groups to allow an almost unlimited combination of sizes. Add a Control Module and optional manual control to complete the system.
-
CXAR/256-MF - Cytec Corp.
This Chassis is intended to control up to eight 16x1 solid state 75 ohm cable TV modules, or may be used to control a great number of 8x1, 4x1, 2x1 or 2x2 modules. It is often used to control a large variety of custom configurations which may be located in separate chassis. When used as a separate driver chassis it can control up to 256 switch points from a 2 RU chassis. LEDs on the front panel show switch and power status. Add Switch Modules, CP16 Driver Modules and a Control Module to complete the system. Keypad Manual manual control with LCD display is optional.
