Transmission Line Pulse
sensitivity tests to analyze IC ESD protection circuitry. Also known as: TLP
See Also: Transmission LIne, Very Fast Transmission Line Pulse, TLP
-
Product
Precision Line Gage
PLG100
-
The PLG100 Precision Line Gage system is specially designed for desktop use in order to measure conductor line widths, conductor line spaces, arcs, circles and other patterns on the PCB. It can measure a conductor line width less than 1 mil. The PLG100 system is unbelievably light weighing only 0.73 kg and providing easy mobility
-
Product
Field-installation Type MLSS Meter (Four-Wire Transmission)
HU-200SS
-
HU-200SS connects immersion type MLSS sensor (SS-90) and measures MLSS in activated sludge. A wide range (0-2000mg/L)of SS contents can be measured with excellent reproducibility using the near-infrared radiation transmission method. Any of the calibration curves of MLSS, Clay (inorganic mud) and Kaolin may be used as standard substances of SS. If "MLSS" is selected for an activated sludge treatment tank, "Clay" for the precipitation treatment of construction sludge, or "Kaolin" for white mud, a concentration can be obtained closer to an analyzed value.
-
Product
SAM Line
-
PVA TePla Analytical Systems GmbH
The SAM Line offers easy-to-use scanning acoustic microscopes for process control and quality assurance as well as for research applications. The individual models are derived from a component platform that complies with industry standards and incorporates cutting-edge production and manufacturing technologies. Thanks to their new high-frequency and transducer technology, our acoustic microscopes enable detailed acoustic analysis in the ultrasound range up to 400 MHz.
-
Product
Automatic Transmission & Engine Oil Pressure Tester
34500
-
Check oil pressure in automotive transmissions and engines. Adapters provide coverage of most domestic and imported cars and light trucks. Gage calibrated from 0-600 PSI (0-4,000 kPa & 0-7.0 BAR). Includes 6 feet of oil proof hose and 10 assorted fittings. Supplied with instructions in a durable vinyl pouch.
-
Product
Winkler ATEX Heated Sample Lines
-
Hazardous area ATEX heated sample lines from Winkler (Germany) for use in zones 1 & 2 (gas) and zones 21/22 (dust). These are specialist heated lines for gas sample handling and process applications, manufactured from high quality, tested and approved materials.
-
Product
Coupling Decoupling Network for Communication Lines
CDN61000-5C
-
• Application Range: ≤4kV, 1.2/50us pulse, 8 wire unshielded twisted pair (UTP) • Test Voltage: Max 4KV, 2 kV (1.2/50 µs pulse when RJ45 connector is connected. Maximum test voltage is 1.5kV when RJ45 female is unconnected or auxiliary terminal is not protected.) • Coupling mode: 90V gas- discharge tube+250ohm Resistor/Each Wire, 8 Wires Simultaneously-Ground (Common Mode) • Input and output interface: RJ45 connector • Terminal layout (RJ45 connector): First pair of lines: pins 1/2 Second pair of lines: pins3/6 Third pair of lines: pins 4/5 Fourth pair of lines: pins 7/8 • Max. operating speed: 1000MBit/s • Max operating voltage: Max 50V DC • Max operating current: Max 1A Related Instruments
-
Product
Transmission
-
Since the beginning, we’ve partnered with international standards organizations to ensure our testing solutions not only adhere to the current standards but also to develop new standards. To this day, our instrument portfolio remains the only one in the world to cover full transmission measurements of all single-mode and multi-mode fiber types.
-
Product
Line Testers
-
GAOTek provides a large collection of certified and feature-rich line testers for sale to the United States, Canada and Globally. These devices are mainly used for line installation, line performance testing, inspection, and maintenance of the telecommunication networks. They are particularly designed to accelerate telecom trouble shooting and with the help of latest technology they are equipped with a smart CPU, IC, and SMT. These devices have some unique features such as caller ID display and last number redial. Moreover, it can also be used for multi-line testing, wire pair checking, inspection of line insulation and test for breaks and faults.
-
Product
Pulse Width Extender
TLP-3011C
-
High Power Pulse Instruments GmbH
*Fully automatic pulsewidth extender*Pulse width up to 1.6 µs in 68 programmable steps of 25 ns*Ultra fast 50 Ω pulsewidth extension with typical 100 ps rise time*High pulse output current up to ±40 A*High performance and high quality components
-
Product
Single-in-Line Reed Relays
Series 113
-
SIL relays - Requires a small area of only 0.15 x 0.5 inches (3.8mm x 12.5mm). 10 Watts Form A or 3 Watts Form C switches. Smallest Form C reed relay
-
Product
In Line HT Ignition Tester
1177
-
Establishes whether there is a high tension spark potential at the spark plug. Hands free operation means no risk of electric shock to user. Ideal for modern vehicles with sensitive electronics. Probe is 55mm long with a lead 100mm in length.
-
Product
Party Line Intercom Conversion
COMMS Series
-
The stand-alone COMMS 300 and the OG-COMMS openGear® units provide a means to interface between two channels of 2-wire party-line intercom audio and two channels of 4-Wire analog line-level signals. The unit is capable of performing auto nulling for each channel with the push of a button. In addition, each of the 4-Wire input and output channel levels are monitored and displayed on easy to understand front panel VU meters.
-
Product
Pulse Tesla Meter
GP-300
-
Pulse field intensity can be read directly. Wave form is observed by oscilloscope. Measuring range:0.01T~9.99T .
-
Product
High Line Pressure Transducer with Digital Interface
P368
-
The Validyne model P368 is a digital differential pressure transmitter designed for high line pressures and industrial pressure measurement applications. Full scale ranges of 8 psid to 10,000 psid are available. The on-board microprocessor provides high accuracy and improved stability in changing thermal environments. Communication via RS485, USB or CanBus provides remote zero and span adjustment as well as digital pressure readings in engineering units.
-
Product
Pulse Pattern Generators
-
The Pulse Master is a Series of Single and Dual Channel Pulse/Waveform Generators that offers a complete array of pulse, standard, arbitrary, sequenced and modulated waveforms with unmatched performance, even compared to instruments designed to generate fewer types of signals.
-
Product
High Voltage Pulse Attenuators
-
Barth High Voltage Pulse Attenuators are matched impedance coaxial attenuators for use primarily in pulsed 50 ohm systems, or where occasional transients would damage ordinary units. The attenuator design closely matches the impedance around each resistor, to that resistor. These attenuators feature an input impedance very close to 50 ohms, with characteristics as good or better than most microwave attenuators. These units are ideal for use in nuclear and high energy experiments. Extensive testing during manufacturing insures very high reliability for single-shot experiments. A voltage coefficient of the resistive film of less than .0001 %/V allows low voltage calibration of most systems.
-
Product
Engine Torque Pulse Simulation
ETPS
-
HORIBA has revolutionized the way vehicle manufacturers test their Powertrains and Front End Accessory Devices. The ETPS dynamometer system accurately produces torsional pulse characteristics of an engine. This new technology employs a sophisticated mathematical model to calculate the resulting torque at the output of the engine based on engine and combustion process parameters.
-
Product
Transmission Line/Cable Testing
-
HAOMAI Electric Test Equipment Co., Ltd.
Transmission Line/Cable Testing products by Haomai
-
Product
Line Monitor
LE-110SA
-
LE-110SA is a handheld line monitor specialized for ASYNC communication which is widely used in the industry. You can control the line monitor by soft screen touch as you do for smart phones. The light weight (300g including batteries) helps you for the field maintenance besides the system developments.
-
Product
Transmission & Hydraulic Test Stands
-
Our equipment tests automatic and automated-manual transmissions. On and off-highway transmission test stands, transmission and hydraulic component test stands and valve body test stands. AIDCO Test Systems offers the latest in modern, electric motor and hydrostatically-driven transmission test stands. All units may include an air-cooled eddy current absorber (standard on the 450E), resulting in minimal dyno test cell noise and reduced maintenance.
-
-
Product
Power Line Meter
-
The Line EMI Meter measures electromagnetic interference in a single-phase AC power line. It plugs into a wall outlet (mains socket) and requires no battery. It immediately displays total line noise in millivolts (range 1999 mV, resolution 1 mV) in the frequency range 10 KHz 10 MHz (the frequency limits at which sensitivity is of the maximum sensitivity). A speaker plays the sound of the EMI, amplitude demodulated, in order to identify the EMI source (such as an AM or shortwave radio station vs. a motor vs. an electric arc).
-
Product
SparkFun Line Sensor Breakout
QRE1113 (Digital)
-
This version of the QRE1113 breakout board features a digital output, using a capacitor discharge circuit to measure the amount of reflection. This tiny board is perfect for line sensing when only digital I/O is available, and can be used in both 3.3V and 5V systems.
-
Product
2 Port Analog Phone Line (FXS)
SIM-2FXS
-
This unit has 2 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, modems, access servers, audio conference equipment or anything that requires phone lines. Telephone line simulator acts like a "telephone company in a box" providing dial tone, ring voltage and all advanced phone line features such Caller ID, Call Waiting, Call Hold, Three Way Calling and many others.
-
Product
Field-installation Type Turbidity Meter (Four-Wire Transmission, Immersion Type)
HU-200TB-IM
-
HU-200TB-IM connects immersion type turbidity/ MLSS sensor (SS-150) and measures turbidity and SS in activated sludge. The sensor can be immersed directly in the sample water tank. Optimal for turbidity and SS management of wastewater and intake.
-
Product
Pulsed Source Measure Unit
-
The SpikeSafe SMU is a precision pulsed source measure unit that precisely sources pulsed current and simultaneously digitizes voltage. Optimized for precise and repeatable high-power LED and laser testing, SpikeSafe™ SMU (Source Measure Unit) current sources deliver precise pulsing with low microsecond rise times, low-jitter triggering and integrated digitizer for more accurate and repeatable high-power LED and laser testing.
-
Product
Green Cross Line and Point Laser
Lino L2P5G
-
The Leica Lino L2P5G uses the latest green laser technology which projects clearer and crisper laser lines at exact right angles to one another. This allows for the highest accuracy of detailed interior tasks. The working range is up to 35 meters depending on the lighting conditions, and can easily be extended up to 80 meters using the laser receiver Leica RGR 200.
-
Product
SAM Premium Line
-
PVA TePla Analytical Systems GmbH
The SAM Premium Line combines acoustic microscopy and optical microscopy. It enables the scanner to be combined with both an inversion as well as a reflected-light microscope. The technology used in the SAM Premium Line is based on a core platform that employs the latest production and research technology. The individual systems are characterized by high throughput, high flexibility and a wide scanning range. They can be expanded to suit customer requirements and specified for the most diverse applications.
-
Product
Pulse And Delay Generator
-
An electronic instrument designed to produce precise, timing-controllable pulses and delays, often used to synchronize multiple devices, trigger events, or test circuits.
-
Product
SAM Auto Line
-
PVA TePla Analytical Systems GmbH
The fully automated acoustic microscopes from the SAM Auto Line enable simple detection of cavities, voids, bubbles, inclusions, and delamination and are ideally suitable for wafer inspection, bond checking, and MEMS inspection. An automatic defect-review software package performs a fully automated evaluation of the entire wafer. The results can be issued as klarf files and VEGA MAP. A GEM/SECS connection is also possible.
