Filter Results:
Products
Manufacturers
Applications
Filters
Electronic circuits which refine signal by blocking certain frequencies, while allowing other frequencies to pass.
See Also: Filter / Amplifiers, EMI Filters, Low Pass Filters, Programmable Filters, Attenuators
-
product
Gas Filters
WITT gas filters enable the finest filtering of impurities in technical gases such as acetylene, argon., oxygen, hydrogen, methane, carbon dioxide, helium, compressed air and ethylene. They thus protect downstream equipment and systems. Some gas filters are also referred to as gas cleaners.
-
product
Tunable Notch Filters
The Ranatec Tunable Notch Filters are critical tools for adaptation to stringent new ETSI/3GPP conformance test specifications for mobile device radio properties, that covers all sub-6 mobile bands and channel bandwidths for 2G/3G/4G/5G. Designed for formal conformance testing performed by accredited test houses, as well internal verification by mobile device vendors. A flexible and easy to use test automation platform to support almost any ambition level, tailored to your demands.
-
product
Individual Optical Filters
Our comprehensive line of Semrock optical filters helps your design attain the best signal-to-noise ratios. Steep spectral edges maximize useable bandwidth, and high transmission or reflection captures the brightest images with best-in-class Flatness. Deep and extended blocking are optimized for your application, minimizing background and crosstalk while reducing cost. Select from the extensive catalog or go with a custom filter to your exact specifications, and remain confident of uncompromising quality, reliability, and reproducible results.
-
product
Low-Pass Filters
Is a filter that passes signals with a frequency lower than a selected cutoff frequency and attenuates signals with frequencies higher than the cutoff frequency. The exact frequency response of the filter depends on the filter design.
-
product
Filters, Collectors, Separators, Purifiers
Parker's filters, separators and purifiers come in a variety of options and media and are used to filter out air or fluid contaminants in an array of industrial and commercial applications.
-
product
Ground EMI Filters
High-frequency signals on ground is never good news - it interferes with normal operation of equipment and creates electrical overstress (EOS). However it is easy to block propagation of EMI on ground by installing highly-effective ground EMI filtes in ground lines. Our unique patent-pending ground EMI filters provide very low impedance for DC and mains' power while effectively blocking propagation of high-frequency currents throughout facility or equipment ground. Ground filters meet safety standards, as well as ANSI/ESD S6.1 and ANSI/ESD S20.20.
-
product
Tunable Edge Filters
Tunable edge filter is a customized product. It usually belongs to 2-port optical tunable filter product platform. Instead of using narrow bandpass filter in the 2-port tunable optical filter, the tunable edge filter utilizes a low-pass or long-pass interference filter. By changing the incident angle of the light beam, the cut-off wavelength will be tuned. Standard Tunable edge filters support C-band or L-band wavelength range.
-
product
Band Pass Filters
High-Pass (HPF series), Low Pass (LPF series) and Band Pass (BPF series) Filters are available, providing desired skirt selectivity and rejection levels with minimum insertion loss in the pass band. The filters are offered in all standard waveguide bands covering 18 to 400 GHz depending on our possibility to fulfil the customers' requirements. Dimensions of filters depends on required specifications. .
-
product
Filters & Switch Filter Banks
PMI offers the highest quality filters, switch filter banks, filter assemblies, diplexers, multiplexers for industrial and military applications in the frequency range of DC to 40 GHz. All PMI’s Switch Filter Banks use PMI’s proprietary Solid-state Switch designs, which offer high speed and improved performance. While there are many standard models, PMI can design and build to meet your specifications.
-
product
RF Filters
Raymond RF offers a complete line of RF filters ranging from 0.4A to 600A in both stand-alone and cabinet-mounted configurations for our QuietBoxes and Anechoic Chambers. Both styles of filters can be supplied with NPT pipe nipples and flange nuts for mounting directly on a QuietBox or Anechoic Chamber. Alternately, both styles of filters can be remotely mounted with shielded conduit running between the clean end of the filter and the QuietBox or Anechoic Chamber.
-
product
Narrow Band Filters (Single Octave)
MINI-POLE® Series
The MINI-POLE® Series of tunable filters is optimized for size, RF power handling, low distortion, and exceptional selectivity. The product line includes several standard designs in various bands to support a myriad of applications. Approximate performance is summarized in the MINI-POLE Series Selection Guide.
-
product
RF Filters
Smiths Interconnect is committed to providing technically advanced, high quality “state-of-the-art” RF Filters, Multiplexers, Switched Filter Banks, and Integrated assemblies, from 100 KHz to 65 GHz. All products are subject to the same rigorous design, manufacturing, and inspection criteria. Regardless of the application, our internal process and procedures help ensure that all products are fully compliant to all specifications. Our R & D activities are constantly evaluating new materials, plating techniques, and manufacturing processes to offer the highest performing components available today.
-
product
Narrow Band Filters (Single Octave)
IMF™ Series
The Integrated Microwave Filter or IMF™ Series introduces accelerated tuning speeds packed in a very small, lightweight filter, providing maximum sensetivity and improved system performance for cleansing your ESM environment. Designed for the military radar market, specifically Active Electronically Steered Arrays (AESA) Radars and Phased Array Radars but compliment a broad range of applications such as; Commercial, Tactical & Military Communications, RF Front Ends (RFFE’s), SATCOM-on-the-move (SOTM), along with Electronic Warfare & Radar applications.
-
product
Harmonic Filters
ENTES Harmonic Filter Reactors are used in serial connection with capacitor banks in power factor correction units. By using these types of detuned reactors it is possible to increase the capacitor impedance against harmonic currents and to keep the resonance frequency under the frequencies in which main harmonic currents occur by shifting the resonance frequency.
-
product
CAT-5 Video Variable Filters
It is often beneficial to use a video driver at the output of a video encoder for power savings, line driving, and additional circuit protection. The video driver is typically configured as an active filter, also known as a reconstruction or anti-imaging filter. The purpose of the reconstruction filter is twofold: it blocks the higher frequency components (above the Nyquist frequency) that were introduced into the video signal as part of the digitization process and provides gain to drive the external 75 Ω cable to the video display.
-
product
Wide Band Filters (multi-octave)
HF-ERF™ Series
The HF-ERF™ is an internally switched 3‑band, low cost, miniature, high performance tunable filter. The HF-ERF™ was designed to have the best insertion loss and Q in the smallest package possible, 2.0” x 2.78” x 0.6”. All HF-ERF™ filters are fully tested and aligned by Pole/Zero for convenience and ease of use. Both SPI and Parallel control interfaces are available in one filter. Modified variants are available upon request.
-
product
"Standard" RF Low Pass Filters
Coaxial Dynamics "Standard" line of RF Low Pass Filters offers several models to choose from at CW power ratings of 100 watts and 200 watts. These filters cover operating frequencies from 88 MHz to 400 MHz with less than 0.5 dB insertion loss and attenuation levels of 40, 50 and 60 dB.
-
product
Tunable Filters
K&L Microwave offers a variety of Tunable Filter Products to satisfy a broad range of filtering applications. Tunable Bandpass and Bandreject filters provide the best solution for pre-tuning the desired signals while rejecting the interfering signals. The method of tuning can be either mechanical via a tuning knob mounted on the front of the filter, or electro-mechanical via an optional remote digital interface such as GPIB, RS-232, RS-422 or BCD.
-
product
Filters
ZF
Antenna Technology Communications, Inc.
ATCi offers a selection of filters designed to reject out-of-band interference.
-
product
Filters / Splitters / Detectors
DiCon’s 100 GHz WDM is designed to multiplex and demultiplex signals in multi-wavelength systems based on the ITU 100 GHz grid. The component uses a thin film filter mounted between a pair of GRIN lens collimators. The 100 GHz WDM is housed in a compact, environmentally stable package that offers superior resistance to humidity and temperature and is suitable for mounting on a printed circuit board or within a module.
-
product
Bandpass Filters
K&L Microwave provides bandpass filters in multiple topologies built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications, as well as product families. Use the quote cart to request a quote on a specific design.
-
product
Automatic Batteries with Filters with Thyristors
BATLVFS1200
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations
-
product
Broadcast Filters VHF DAB
The filters offer a compact and flexible solution for both transmitter mask filtering and digital RF channel combining. The DAB filter range is founded on RFS' world-leading RF combining technology and utilizes a similar platform of components to the company's VHF Band III;digital television combiners. DAB filters can beincorporated within transmitters to provide critical mask filtering of the digital RF signal, in keepingwith global DAB standards. When used as the key components of a balanced DAB combiner, thefilters can achieve both critical transmitter masking and adjacent channel combining simultaneously,eliminating the need for additional filters within the transmitter.
-
product
Super-Notch YIG Band-Reject Filters
YIG Tuned BRF patented technology gets closer to the ‘perfect notch'. Leveraging a long heritage of engineering innovation in YIG technologies, Teledyne RF & Microwave has developed a line of YIG Tuned Band-Reject Filters powered by patented new technology that overcomes many long-time design limitations inherent to YIG Band-Reject or “notch” filters. Our new line delivers major advancements and unequalled performance.
-
product
Fiber Bragg Grating And Optical Filters
Exail is committed to develop and manufacture optical components with excellent performances to support the most diverse industrial applications such as Telecom, sensing, defense, space, fiber laser and harsh environment.
-
product
dv/dt Filters
dV/dT Output Filter Modules effectively protect motors against these high voltage spikes due to the use of motor cables between IGBT based motor drives and motors.
-
product
Optical Filters
Alnair Laboratories Corporation
The filter exhibits an ultra-sharp roll-off of 1500dB/nm(12dB/GHz), without compromising the flexibility ofbandwidth- and wavelength-tuning. Ideal for DWDMchannel selection and removing ASE noise.
-
product
Automatic Batteries with Filters with Thyristors
BATLVFS600
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
product
Sine Filters
Sine Wave Output Filter Modules provide satisfactorily smoothed sinusoidal waveform with low residual ripple form square waveform with high voltage spikes, present at the output of motor drives.
-
product
Real Time Digital Filters
Real Time Digital Filters can be used to filter a measured signal in real time. Filter characteristics can be defined by the user to meet the requirements of a specific application. Real-time digital filters are applied in the data conditioning phase. The filters are designed with a graphic design tool and then uploaded to the front-end for real-time calculation. The graphic design tool defines the filter performance vertical axis with a dB scale. The horizontal axis is defined as relative frequency.
