Test System Integration
-
Product
Liquid Test Fixture
16452A
Test Fixture
The 16452A provides accurate dielectric constant and impedance measurements of liquid materials. The 16452A employs the parallel plate method, which sandwiches the liquid material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixure.
-
Product
VR/AR/MR Calibration Platform
Test Platform
AR, VR and MR device calibration is critical for product performance. Leverage Averna’s standardized alignment platform to efficiently calibrate cameras and Inertial Measurement Unit (IMU) modules with supreme accuracy. Easily customize or upgrade the base platform into the automated quality solution to best fit your manufacturing requirements.
-
Product
EMI Test System
TS9975
Test System
The R&S®TS9975 is the base system for conducted and radiated EMI measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for large equipment under test. Combinations of different applications or incremental expansion are easily possible.
-
Product
Test Fixture (SMD Components)
16034E
Test Fixture
Perform impedance evaluation on a minimum SMD size of 1.6(L) x 0.8(W) [mm]
-
Product
Scienlab Charging Discovery System (CDS) – High-Power Series
SL1047A
Battery Test Platform
The Scienlab Charging Discovery System – High-Power Series from Keysight enables you to test charging interfaces of electric vehicles (EVs) and EV supply equipment (EVSE) during high-power charging up to 1,500 V DC and ±600 A DC. With the CDS can perform all necessary conformance and interoperability tests according to worldwide charging standards. Our new solution, which features the separate Scienlab Cooling Unit with interchangeable liquid-cooled charging adapters, also enables a high-power upgrade of the SL1040A Scienlab Charging Discovery System - Portable Series.
-
Product
Bloomy Simulation Reference System
System
The Bloomy Simulation Reference System provides a hardware in-the-loop (HIL) test environment for dynamic, closed-loop testing of many aerospace and transportation control systems. The reference system integrates the computing, I/O, and software components needed for standalone use or to form the basis of a more complex test system.
-
Product
RF-Antenna Communication Links Functional Test
Functional Test
The application encompasses functional tests of very large quantities of automotive antenna amplifiers, plus parallelization of tests by implementing several test stations in a rotary indexing table. The DUTs are inserted manually and after final assembly, they are loaded into the rotary table; this requires manual triggering by the operator.
-
Product
Functional Test System
TS-5040
Functional Test
The Keysight TS-5040 Functional Test System is a cost effective, robust and reliable test system that gives you the lowest cost of ownership. In addition, the open architecture Test Exec SL gives you the flexibility to do just about anything you want.
-
Product
NTS Platform
Test Platform
Manufacturers all over the world are leveraging our NTS platform for products with rotating or otherwise moving parts, or produce sounds. Typical applications include mass production of air conditioning units, pumps or small electric motors, where errors in assembly can cause malfunctions or significantly shorten service life. This test platform is customized to your specification and application. Feasibility studies are available to ensure your solution is exactly what you are looking for.
-
Product
Sealed Beam Bulb Testing System
H710019SSL
Test Platform
EOL test for manufacturing of bulbs with LED for applications requiring to ensure watertightness: vehicles, marine, swimming pools, operating rooms, classified areas (Ex Zone), etc. The test system checks in a short time all the light and electrical characteristics of the bulb. A high precision Micro Leakage Meter also checks that there are no leaks between the environment and the inside of the bulb. The test results are recorded on the PC and can be printed on a quality control label attached to each unit.
-
Product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
Test Fixture
Stopper kit includedYAVCANCON2 for fixture identification not included
-
Product
Smart Aircraft System
System
The Astronics Smart Aircraft System makes that possible. Our patented system enables the immediate, cabin-wide gathering of thousands of data points using sensors & IoT (Internet of Things) technology. The result? You get the insightyou need—when you need it. Insight that helps you on every flight. Insight that allows you to improve your operational efficiency, your cabin safety, and your overall passenger experience.
-
Product
Regenerative Battery Pack Test System
17020E
Test System
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
Product
Mezzanine System
5041
System
ECM P/N 5041 provides eight channels of RS485 / RS422 I/O with fixed 120 ohm termination for each channel. Speeds are up to 30M bits per second. All channels power up as inputs. Also transceiver inputs are always enabled for loop back diagnostic use when the outputs are enabled. Software can enable outputs on a channel by channel basis.
-
Product
Mezzanine System Carrier
MMS8010 / MMS8011
System
The Abaco ECM 3U VPX carrier supports up to six Abaco Systems Electrical Conversion Modules (ECMs) in a VITA 46 VPX form factor. Each ECM site connects 32 single-ended 3.3 V signals to the FPGA. The specific ECM board installed on a site converts the FPGA signals to 16 I/O signals, for a total of 96 I/O signals across the six ECM sites.
-
Product
Modular Breakout System 160-Pin Plugin Module
95-190B-003
Modular Breakout System
The 95-190B-003 Plugin Breakout Module is designed to be fitted to a PXI 40-190B Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
Product
Advanced SoC Test System
3680
Test System
The Chroma 3680 is an advanced SoC test system with data rate up to 1Gbps. The Chroma 3680 is capable of conducting parallel tests on multiple chips to meet the digital and analog IC testing requirements, with applications including MCU, digital audio, digital TV, set-top box, DSP, network processor, field programmable gate array (FPGA) and consumer electronics.
-
Product
Mezzanine System
5093
System
ECM P/N 5093 provides 2 independent full bridge circuits. The two full bridge circuits can be used together to drive one small two phase stepper motor. Each full bridge circuit can drive one small dc motor or other bipolar load. Note all inductive loads should employ transient protection.
-
Product
EVSE Test Platform
Test Platform
To manage both the challenging high-power requirements of electric vehicle supply equipment and the market demand, it is crucial to rely on a test system that performs to your specs. The right system needs to combine the tools for reliable asset communication, microgrid management, effective protocol simulation and high-power testing. This EVSE platform combines the right energy regeneration equipment with 25+ years of test experience to deliver the results you need to meet conformance in the time you need it.
-
Product
In-Line Test Fixture for 6TL33/6TL36
AB799/AT799
Test Fixture
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 1.000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
Product
Automotive Ethernet Test Fixture
AE6941A
Test Fixture
The AE6941A automotive Ethernet electrical test fixture provides easy access to automotive Ethernet electrical signals so you can perform conformance testing and device characterization quickly and easily.
-
Product
Modular Breakout System 37-Pin D-type Plugin Module for 40-293
95-293-001
Modular Breakout System
The 95-293-001 Plugin Breakout Module is designed to be fitted to a PXI 40-293 Programmable Resistor Module as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
Product
6TL24 Combinational Base Test Platform
H71002400
Test Platform
The 6TL24 is the Base platform ideal for Combinational test (ICT+FCT) in low to mid volume, high-mix electronics productions. A dual-stage pushing mechanism will allow performing both, the FCT and the ICT test, without the need of changing the test platform and with a low cost fixturing technology. To do so, the exchangeable cassette fixture must be designed with two-level probes. IN the 6TL24, the second level is reached thanks to a pneumatic actuator.
-
Product
EBIRST 50-pin D-type To 37-pin D-type Adapter
93-005-418
Test Adapter
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
Radar Test System
UTP 5065
Test System
Radar sensors are core elements to realize autonomous driving. The UTP 5065 radar test system from NOFFZ Technologies has a compact vertical design and contains everything needed to allow State-of-the-Art measurement and sensor calibration. The test bench setup and component selection are tuned to get best possible results for highly accurate and cost-efficient testing in production of automotive radar sensors.
-
Product
Optimize Throughput And Cost For MmWave 5G Device Functional Test
Functional Test
Test engineers always have faced tough new test-coverage challenges. Those introduced by 5G measurements at mmWave are no exception, as they require over-the-air (OTA) radiated test solutions. But never have these pressures seen today’s intense time-to-market, manufacturing volume, and operational expectations! A solution that meets these demands must:
-
Product
Universal OTP Functional Test System for the Production of Level and Fluid Sensors
Functional Test
Multifunctional function tester with parallel test function based on the LXinstruments OTP2 system platform. The system is used for assembly, final test and calibration of liquid and level sensors for commercial vehicles, construction machinery and shipbuilding in a high mix / medium volume environment.
-
Product
Massively Parallel Parametric Test System
P9001A
In-Circuit Test System
The highest throughput parallel parametric test solution. 100-pin parallel measurement capability and faster single parameter measurement than Keysight 4080. Good data correlation with Keysight 4080. New per-pin parametric test unit module with all basic measurement function (voltage, current, capacitance, pulse, frequency). Easy development of parallel test plan. Easy migration from 4080 environment. Proven in 1st-tier logic foundries and memory companies.
-
Product
3-Axis Non-Robotic Automated Testing System
AT3
Test Instrument
The Instron AT3 is a space-efficient, highly adaptable 3-axis mechanical testing platform designed for automated execution of tensile, compression, flexural, and lap shear tests. Built to comply with a broad spectrum of ASTM and ISO standards, it’s well-suited for evaluating materials such as plastics, elastomers, thin films, foils, and metals. The system streamlines the entire testing workflow from specimen measurement and handling to strain measurement and specimen disposal—enabling users to load up to 160 samples and let the AT3 take care of the rest. Boost productivity, reduce manual intervention, and achieve consistent, dependable results with every test cycle.
-
Product
PXIe System Sync Module, 2 Port
M9032A
System Sync Module
The M9032A has a Soft Front Panel (SFP) that provides a graphical user interface to the system sync module. It allows the user to set up the most commonly used functionalities of the module. The SFP also gives you the ability to check the module's connection status, configure the reference clock and IO settings, and perform firmware udpates.
