Test System Integration
-
product
Test Analysis for Land Seismic Systems
Testif-i Land
Testif-i Land is an independent, powerful and cost effective software suite that allows you independently process instruments, source and receiver tests to confirm that the equipment is performing correctly and within specification. The software includes modules to perform comprehensive analysis of vibrator wireline similarity test data. Analysis includes a harmonic intensity plot which can highlight problems such as sub-harmonics which may not be seen on numerical results. Geophone pulse tests can be analysed using the receiver response module and test data from third party geophone testers can be graphed and statistics produced for ease of interpretation.
-
product
Optics Test Systems
Mobile Wedge Angle Sensor With Positioning System
Optik Elektronik Gerätetechnik GmbH
Mobile wedge angle sensor for determining the wedge angle and the radius of curvature of glass panes, eg windshields of automobiles, helicopters, airplanes or rail vehicles.
-
product
Inertial And Integrated GPS/Inertial (IGI) Sensor Testing
SimINERTIAL
Overcoming PNT/GNSS positioning challenges with precision inertial sensor emulation, for powerful IGI testing. Integrating inertial sensors is an effective way to overcome the weaknesses of GNSS positioning systems. However, it also adds a set of challenges to the development process. Once inertial sensors have been verified, it is necessary to test the complementary positioning systems alongside each other.
-
product
Solar Test Systems
AMETEK Scientific Instruments manufactures a range of application specific XM (Xtreme Measurement) products focused on solar cell / photovoltaic research (developed in collaboration with Professor Laurie Peter of the University of Bath, UK). These products are so versatile that they can also be used for photoelectrochemical (PEC) water splitting applications; and make use of Solartron’s unique high performance XM specified potentiostats and frequency response analyzers to provide a full complement of techniques for research into energy, corrosion and analytical electrochemistry.
-
product
Integrating Spheres
Instrument Systems Optische Messtechnik GmbH
Determination of radiant power or luminous flux from light sources with the aid of integrating spheres is one of the most important procedures in photometry. Designed as a hollow sphere whose inner surface is coated with a diffusely reflecting material, the integrating sphere ensures complete integration and mixing of light radiation. This is then output on a detector port for measurement.
-
product
LED Driver Automatic Test System
ATE-2
•This system includes 2 groups (left and right); the 2 groups can work in turn, so that to improve the work efficiency. For example, if the left is on working, then the right can make wire connection. •It can test 4 LED drivers input and output at one time. •The equipment can connect with electronic load and LED load, the two difference loads can be fast switch under the control of computer. •Enable to print out the series number and parameters of sub-quality products by working with a micro-printer, •Enable to achieve the bar-code record function by working with a bar-code scanner. •The test report can be saved as Excel file for consult, statistic and analysis purpose. •Good software interface to freely choose the difference parameters combination, so that to meet different demands. All the parameters can set limit, and with the quality analysis function.
-
product
Optics Test Systems
Scientific Instrument Engineering
Optik Elektronik Gerätetechnik GmbH
Development, design, manufacture and assembly of opto-mechanical assemblies and complete devices, including software.
-
product
Multi-site Module Testing System
TCIII-3200ST
TurboCATS introduces a new line of redesigned TCIII-3200ST DDR4 and DDR3 multi-site module testing system - compact, high-performance, and equiped with enhanced productivity features. The TurboCATS TCIII-3200ST module test system features an optional 8, 16 or 64 module testing, in parallel, for high throughput on your production floor.
-
product
16-Station Testing System
The ElectroPuls 16-Station testing system performs high cycle fatigue testing on multiple samples simultaneously, with a fatigue-rated load cell included on each station. The fixture uses a carousel designed with high stiffness and low mass to enable high frequency testing and reduce test time.
-
product
Monochromator-H With Integrated Halogen Lamp
We have combined our proven Monochromator-F with a halogen lamp to realize a compact tunable light source for the wavelength range 340 – 2000nm, the Monochromator-H. The very smooth and consistent spectrum of a halogen lamp makes it the ideal solution when monochromatic light with a freely selectable wavelength in the UV, VIS and NIR is needed.
-
product
Automatic Transformer Test System
TH2829AX
Changzhou Tonghui Electronic Co., Ltd.
*Number of Test PIN: 20*Frequency: 20Hz-200Hz, Resolution: 0.5mHz*Signal Level: 50mV-2Vms (Option 2nv-10Vms)*Test Speed: max 13ms
-
product
HEV / EV / Grid Emulators and Test Systems
With Scienlab test systems and test software, Keysight offers customized test environments for the development and testing of electronic components according to hybrid and electric vehicle testing standards. Our solutions help you to accelerate your e-mobility applications from the battery, Battery Management System (BMS), inverter, the charging interfaces of Electric Vehicle (EV), and Electric Vehicle Supply Equipment (EVSE).
-
product
Macro-Vickers Hardness Testing System
LV Series
LECO's LV Series Macro-Vickers Hardness Testing Systems offer an affordable testing system suitable for larger, heavier samples used in welding and other demanding applications. Models include analog and digital, with options to upgrade to automatic configurations.
-
product
Automatic Transformer Test System
TH2840AX
Changzhou Tonghui Electronic Co., Ltd.
■ The test speed is as high as 1000 times/s (>10kHz), without relay action time ■ Test level up to 20Vrms ■ The bias voltage is built-in ±40V/±100mA/2A ■ Up to 288 test pins (only TH2840NX) ■ Industry-friendly user experience: Linux bottom layer, built-in help file
-
product
Pneumatic Vertical Shock Response Spectrum Test System
KRD14 series
KRD14 series pneumatic shock response spectrum tester is used to measure and determine the shock resistance of electrical and electronic products or packaging, and to evaluate the reliability and structural integrity of the test product in a shock environment. The shock response spectrum is the total result of a series of single-degree-of-freedom linear systems with different natural frequencies subjected to the same shock excitation response. When a product is subjected to an impact, the maximum value of its impact response means that the product has a maximum stress. Therefore, the shock response spectrum tester can better simulate the shock wave and shock energy suffered in the real environment.
-
product
RTView® Integrations
Middleware monitoring that integrates with multiple outside technologies
-
product
Fast Digital Integrator
FDI2056
The Fast Digital Integrator FDI2056 is the world's fastest and most sensitive voltage integrator. Simply plug in a sense coil and measure fast, low-level magnetic field disturbances such as eddy currents in a switched magnet.Equipped with a high-speed Analog-to-Digital Converter (ADC), high-resolution clock, and highly optimized digital integrator, the FDI2056 boasts a maximum of 500 000 partial integrals per second and provides resolutions down to 10-14 Vs with an accuracy of 10 ppm. Magnetometer Fluxmeter
-
product
EST-200 Emission Safety Test System For Toys
Hangzhou Everfine Photo-E-Info Co., LTD
The system can test the radiation intensity, irradiance, light color expansion angle, peak wavelength, dominant wavelength, bandwidth, etc. of various toy light emitting devices. The measurement conditions meet the CIE127 standard, and the test report meets the ENIEC62115:2020 standa
-
product
Battery Pack Test System
*Easy to see now test progress*Can cycle test*Provide Charge, Discharge, Suspend, FOR, LOOP Mode Select*When Charging, set the stop current to stop charging when fully charged so as to avoid overcharging that will damage the battery. When Discharge, set the stop voltage to stop discharge when discharging to lowest so as to avoid over-discharging that will damage the battery.
-
product
DynoLAB Test Cell Supervisory System
SAKOR Technologies’ DynoLAB™ data acquisition and control systems offer reliable, cost effective automation of all types of dynamometer test systems. As with all SAKOR products, the DynoLAB system undergoes a continuous program of upgrade and improvement, regularly expanding and enhancing DynoLAB’s capabilities.
-
product
802.11be Test System
IQxel-MX
Next generation wireless devices Access Points, CPEs and client devices like smartphones or tablets based on the IEEE 802.11be EHT (Extremely High Throughput) standard require stringent RF performance to meet the latest standard requirements.
-
product
Automated Shock Test Systems
AutoShock-II Test System
The AutoShock-II is a fully automated series of shock test systems used to measure and identify product fragility levels and evaluate protective packaging. With the simulation of real world shock pulses and impact energy levels, manufacturers can systematically test and optimize product design and packaging. L.A.B. Equipment, Inc.''s fully automated computer controlled shock and data analysis test systems are the critical path in accomplishing this optimization.
-
product
Portable Test System
MT781
Actual value, vector, curve displayCurrent and voltage generationerror measurementMeasurement of harmonics up to the 40th
-
product
Diagnostic Test Tools For Switching Systems
You know that verification and diagnosis of complex switching operation in a test system has always been an issue. Two of our latest offerings in diagnostic test tools provide a quick and simple way of finding relay failures within LXI, PCI and PXI switch systems.
-
product
Relay Test System
Relay test products that combine a flexible hardware architecture with advanced test software. Relay tests can be constructed within minutes and displayed using a very simple interface, making the system ideal for low-cost production applications.
-
product
Relay Testing System
UNO
With high power outputs package in an extremely compact and rugged system, the UNO has a tremendous power-to-weight ratio. The design incorporates the latest in modern digital microprocessor technology to achieve unbeatable output characteristics in terms of power, accuracy, low distortion, and dynamic capability. This hi-tech solution enables the testing of many different functions required in relay testing without the need of additional accessories.
-
product
SSFDR Software Integration Rig
MS 1112
Software Integration Rig (SIR) is an Industrial PC based system is used to test the SSFDR (Solid State Flight Data Recorder) of SU30 Aircraft. SIR is a PXI based test platform and it is used to test independent and integrated software tests of the SSFDR.
-
product
Battery Formation and Testing System
BFS 2000
BENNING Elektrotechnik und Elektronik GmbH
For many decades now, BENNING has designed and manufactured charge/discharge converters for the battery industry. These converters are used in both the production and testing processes involved in battery manufacturing and for series-testing of batteries. BENNING's BFS battery production and testing system provides a solution which makes it easier to control and monitor production and test processes which saves both time and energy. When used in power stations and rail applications (mobile version), it can be used to test and maintain a wide range of battery types.
-
product
AirTech Test Systems
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
Hillger NDT has developed AirTech testing technology for the requirements of air-coupled testing. Our USPC 4000 AirTech ultrasonic testing system and our robust AirTech sensors consisting of optimized transmit and receive probes deliver optimal results under demanding conditions.
-
product
ESI(Electronics Systems Integration Unit)
MS 2004
The ESI subsystem provides platform interfaces like Gyro and on board Radar Blanking. This unit receives Analog and Digital GYRO inputs from ship and pre- trigger pulses from on board radars of the ship. This unit measures and provides the ship heading data to VARUNA ESM system. It also provides Heading, Roll and Pitch data to the ECM system. This unit also generates band wise composite ESM Rx. Blanking gates and provides all the required interfaces to ESM receiver, ECM System and System Controller units.
