-
product
PCIe Docking Stations
PCIe Docking Stations allow the extension of Desktop and Laptop PCs by PCIe slots in external chassis. Different solutions are available from different vendors world-wide. A Docking Station can be a single card chassis or a 19" rack with 16 full-size slots. Spectrum no longer sells Docking Stations due to the low demand and Spectrums own Ethernet-based digitizerNETBOX and generatorNETBOX solutions.
-
product
High Power Rack And Panel Connectors
LSH Series
The LSH rack and panel connectors include leading-edge Hypertac® hyperboloid technology. The Polyphenylene sulfide (PPS) insulators interconnect technology ensures LSH connectors are easy mating. The LSH Series delivers customers a high life cycle.
-
product
Multiple Channel Burn In Power Supply
MCPS
The most important features of this burn in power supply is its ability to hold a constant output for each channel even in the event that a unit under test on one channel may short and fail. Since each channel has it''s own transformer, no glitches or voltage spikes can get into any of the other channels. This image shows the results as the second channel from the left is shorted with a small wire and the circuit breaker pops out. Used for burn-in testing and other timed testing where power isolation is required. Very basic simple circuit, see schematic below. Cleans and frees up benchtops, burn in racks and work space clutter. Available in benchtop or rackmount.
-
product
High Performance/Software Controllable RF Multicouplers
1U High Performance Rack Mount Broadband Multicouplers, with configurations up to 1×8 or switchable 2×4 configurations. Features include High Output/Output Isolation and Software Controllable power level and amplitude balance.
-
product
LED Driver Aging Rack
LEDRACK-100W192P
• Application range: LED driver and multi channel driver power aging. It has equipped with computer operation and monitor system. The working condition can be set by the computer, and the computer will record real time data to do statistical analysis. • The parameters of load can be set freely on the software, to monitor the real time voltage, current, and power etc • Load mode: CC, CV, CR, CP, and LED • Aging Control System includes: ON/OFF control signal output; Signal of relay switch control; K type thermocouple temperature acquisition • The channels are parallel connected under arbitrary load mode, which can allow product power expansion • The LED Driver Aging rack will design according to customer’s LED driver power and aging quantity per time • Automatic current switching function (optional) • AC power meter to measure modules, and test power input characteristics (optional) • Temperature monitoring function at product zone (optional) • PWM dimming and two sets of logic control signal function (optional)
-
product
G12x Slide Mount
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common rack depths. The G12x uses the same platform and slides as the G12, providing support up to 180 lbs (81 kg) to accommodate the largest fixtures. G12x accepts ITAs designed for both the G12 and G12x.
-
product
Monicon Gas Monitors
Monicon Gas Monitors are innovative, cost-effective, wall and rack mounted units, with the ability to monitor single or multiple channels. Before ordering, customers can select from a range of toxic gases, combustible gases and oxygen, for monitoring in a wide range of applications.
-
product
12 Block Desktop Receiver
VGR12
VG Mass Interconnect products provide a common Universal interface for your custom test rack and simplifies functional test across your product line. Mass interconnect bench-top and rack mount receiver Plug and play interface blocks for signal, coax, high current, pneumatic controls, and more Stable proven products with 25 years in service Best cost of ownership Fast delivery next day on key products! Compatible to currently available test instrumentation and platformsThere are a number of different block types: Coax up to 26 GHz Power up to 150 Amps Coax and power combined Signal: up to 170 pins, @250 VAC/5 Amps Pneumatic: up to 13 fittings Vacuum: port modules High speed: USB 3.0, HDMI, RJ45
-
product
VPC Receiver Frame
ABex REC21-84TE-EXT
Robust and flexible interconnect solution for test fixtures. Designed for the use with ABex PXIe Rack 18 it provides support to equip all 21 slots with VPC interconnect modules. In addition, it offers 6 more slots on the bottom, below the ABex rack to feed through signals from external measurement devices.The interface uses the well-known Virginia Panel connectors with more than 20.000 guaranteed mating cycles. To build DUT specific test fixture, we also provide the corresponding ITA mounting frame (ITA = Interchangable Test Adapter).
-
product
High-Density Precision SMU Mainframe (4 Slots, 1U)
PZ2100A
The Keysight PZ2100A is the precision source / measure unit (SMU) mainframe that uncompromisingly and densely integrates 20 SMU channels into valuable 1U height, full width, rack space with flexible module options at their best performance. It supports a variety of resources such as the Keysight PZ2110A Precision SMU, PZ2120/21A High-Speed SMUs, and PZ2130/31A High Channel Density SMUs with multiple functions such as pulser and digitizer, as well as precise voltage / current sourcing and measuring to adapt to a wide range of application requirements. The PZ2100A has 4 slots and allows any mixed module configuration for flexible scalability.
-
product
40GHz Four Channel MW Signal Generator 19" 1U Rack
LSX4094R
The LSX4094R is a 40GHz Four Channel Microwave Signal Generator, offers industry leading performance, in a 1U, 19” rack-mounted box. It features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The design offers excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
product
Rack Mounted Load Banks
Traditional commissioning is a daunting task. Since formal system operation doesn’t begin until the system is commissioned, the commissioning team experiences intense pressure to complete the commissioning process quickly. Commissioning can involve high expense and requires staffs from different departmental disciplines to work together. For these reasons data center commissioning has almost uniquely been associated with large data centers (over 20,000 ft2 or 1,858 m2). In the recent past, many data center managers chose to roll the dice and perform little or no commissioning, relying only on start-up data to press ahead with launching the new data center. Given the reality of 24x7 operations, however, the alternative of exposure to major system failures and accompanying downtime is no longer an economically viable option. Commissioning has now become a business necessity. JUNXY series AC & DC rack mounted load banks can be used to introduce heat loads and to allow for simultaneous testing of both electrical and cooling systems.
-
product
Midi Rack 120*60*80cm
OTP2 module no.002
The rack serves as the basic structure for your individually designed test system. Various OTP² modules can be installed in the 120 x 60 x 80 cm rack in order to implement a wide variety of test requirements.
-
product
Multiple-Bus Architecture Cable/Harness Test System
CKT1175-MBA
The CKT1175-MBA (for multiple-bus architecture) will provide seamless testing of electronic racks, panels and chassis containing passive and active components such as relays, solenoids, switches, circuit breakers, lamps and LED's, diodes, resistors, capacitors, etc. This functionality is made possible by a switching matrix that is up to 10 levels deep, plus a multiplexer that controls the various stimuli sources, instrumentation connections, and external energization outputs.
-
product
GPS over Fiber
*High Dynamic Range GPS to Fiberoptic Transmitter and Fiberoptic to GPS Receiver*Compact NEMA rated outdoor Fiber Transmitter provides +5VDC Bias for GPS Antenna LNA*Rack mounted Fiber Receiver provides 8 RF outputs and integrated monitoring and alarming*Cost effective solutions for distribution of GPS signal over long distance
-
product
Rack Mount Kestrel Chassis A-Series
0072
ATXstyle Motherboard, 3 x 5-1/4" Bays, 2 x 3-1/2". A 10-Slot HP 1000 backplane, cooling fans, and slides are provided plus space for a standard ATX PC motherboard, diskette and hard drives (3 x 5-1/4" and 2 x 3-1/2").
-
product
Rackmount Kit
34190A
The Keysight 34190A (5063-9240) rackmount kit is designed for use with only one instrument, mounted on either the left or the right side of the rack. The kit includes one rack flange and one half-rack width filler panel, 4 screws to attach the instrument, 4 rack screws with nuts and installation instructions in English.
-
product
Recess Mount Adapter Kit For M9018B And M9019A
Y1216B
The Y1216B is a complete rack-mounting kit for the M9018B and M9019A PXIe chassis. It includes rack flanges, handles, and attachment hardware. Y1216B suspends the chassis in a Keysight rack using only 4U of rack space. It also recesses the chassis by 4 inches. This kit is not compatible with the Y1270A Front Panel Interfacing Kit.
-
product
Fiber Racks & Cabinets
Wuhan Sunma Technology Co., Ltd.
Optical Distribution Frame (ODF) is integrated components in any fiber management system to handle termination and cross-connection of cables. Pre-terminated ODFs with cables are pre-installed with connectors and cable for quick and easy installation. Units with pre-terminated cables offer advantages such as faster installation, resulting in shorter time to revenue as well as guaranteed quality and performance. SunmaFiber offer optical distribution frame in different size, such as 1U 12 ports, 1U 24 ports, 2U 36ports, 3U 48 ports, 4U 72 ports. Several cable options are available.
-
product
Pioneer Seismic Cabinet
The Pioneer rack is the cornerstone of our broadcast cabinet line, offering flexibility and strength. With a weight capacity of 2,000 lbs., Pioneer’s heavy-duty frame is designed with cross braces interlocked and welded into the corner post.
-
product
Custom Ultra-Fast Data Acquisition Systems
Complete Out-of-Box Data Acquisition Solutions. Fully integrated data acquisition systems shipped directly. Convenient Plug and Play DAQ Environment. Absolutely NO Set-Up time!*. Your choice of chassis. (e.g. Rack, Tower, Shuttle, etc.). Windows™ or Linux Operating Systems available. Multi-Board, High Channel Count configurations..
-
product
Rack Mount Kestrel Chassis M/E/F-Series 37-slot
0228
This chassis has a 38-slot 21MX backplane of which 37 are available to the user. It also includes power supply and cooling fans. A firewire Chassis Interface Card (CIC) must be purchased to provide back-plane signals from the Kestrel to the chassis.
-
product
RF Amplifiers up to 6000 MHz
Includes RF and microwave amplifiers covering the band from 500Mhz to 6000Mhz in a single module with either GaN or GaAs devices. Custom and standard power amplifiers available with high linearity, low noise figure, and very low error vector magnitude (EVM). Our rack systems and select modules include Automatic Gain Control (AGC), Automatic Level Control (ALC), and peak/pulse/average detection useful in OTA, MIMO, and CTIA testing.
-
product
Rack Systems
Real-time testing and validation often require versatile testing platforms, providing a high number of different signals ranging from low-power communication and sensor signals to high-power actuator signals. Integrating all the necessary components in one standard system and designing signal-conditioning for all interfaces is time-consuming and requires specific expertise.
-
product
Rack Module with Standard Contactors without Anti-Harmonic filters
MOD Rack
Lifasa - International Capacitors, SA
The MOD-RACK control units include, in a compact form, all the components necessary for the operation of a step of a standard capacitor bank. MOD-RACK modules are divided into two basic blocks: power block and control block. The two blocks are mounted in a small frame to be installed in an electrical panel.
-
product
Value Power in ABS Plastic Housing (12) 5-15R 1U/0U V/H
EPS-1215-HVP
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
product
Generic RF ATE Test
The Generic RF ATE is developed to test the Radar and Radar Subsystems. The ATE is primarily built using an instrumentation control, precision RF routing systems and rack mounted test instruments. Generic RF ATE system enables measurement of parameters of Radar equipment such as Local Oscillators, Waveform Generators, Up and Down Converters, Analog Receivers, Array Group Receiver Units, TR Modules. The ATE is configured to test the Radars upto 18GHz frequency range.
-
product
4-Slot USB/LXI Modular Chassis
60-105-001
This 4-slot USB/LXI modular chassis offers a small lightweight form factor, making it ideal for portable, benchtop, and space restrictive applications. The chassis is designed for desk or rack mounting and features remote control via USB or LXI Ethernet. Remote control over a network enables the switching function of a test system to be located as close as possible to the target equipment.
-
product
Midirack - 120 x 60 x 80 cm
OTP2-Modul-Nr002
The rack serves as the basic framework for your individually designed test system. Various OTP² modules can be installed in the 120 x 60 x 80 cm rack in order to meet the most varied of test requirements.The modular architecture of the OTP (Open Test Platform) is based on a flexible instrumentation matrix, LXI-based sources and measuring devices, combined with a high-quality transfer interface for connecting the test adapters. The systems can easily be expanded with customer- and application-specific functions. We use standardization to build cost-effective systems that still fit your requirements exactly.
-
product
G12 Slide Mount
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common rack depths. All slides are rated to support 180 lbs (81 kg) to accommodate even the largest fixtures. To order, measure rack depth between mounting rails. With this measurement choose the slide mounting kit that fits the rack. A rack extender kit is available for mounting to racks with recessed rails.
