-
product
Metered Power with Audible Alarm (14) 5-15R 1U/0U V/H
EPS-1415-HVA
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
product
Switch Mode Power Rack Rectifiers
The Switch Mode Power Rack Rectifier is a complete modular rectifier designed as a ready-to-go system to generate high-quality DC, available in air or water cooling.
-
product
Programmable AC Power Source
Model 8600 Series
- Compact size and light weight, standard 19″ rack construction- Step-less frequency setting from 45 to 450Hz- Very low distortion sine wave output- Output voltage range selectable 135 or 270V AC- Galvanically isolated input/output- Independent on/off switch for input and output- 16×2 vacuum florescent display for parameter display- Complete operation through push switches and a digital rotary encoder- Automatic protection against overload, short circuit and over temp.- Built in PFC to provide 0.99 input power factor and wide input range- Conforms to EN55022, class A, safety standard EN60950
-
product
Receiver, G12, 12 Module, Rack Mount
310104338
Receiver, G12, 12 Module, Fixed Rack Mount Unit 15" Platform Supports 275 lbs
-
product
Dual Output Digital Lab Series Regulated DC Power Supply – Upto 1280W
- 300W to 1280W different combination- High current density.- 19″ rack adaptable -3U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation- Optional, at extra cost- Over voltage protection- 19″ rack mounting- Analogue programming and monitoring for V&I
-
product
Digestion Systems
Tecator line
FOSS Tecator line Digestion systems are based on a digestion unit and a tube rack, allowing fully automated digestion for convenient, safe and flexible Kjeldahl analysis. Two way PC communication supports traceability and GLP. These versatile digestion systems are capable of handling eight, twenty or forty tubes in volumes of 100 ml, 250 ml or 400 ml dependent on chosen configuration. Parameters: Kjeldahl digestions, Chemical Oxygen Demand & other reflux chemistries, Trace metal analysis by AAS or ICP instruments. Sample types: Raw materials and finished products in Food, Feed, Agriculture and related matrices, Water & Wastewater and a wide range of industrial compounds.
-
product
DC Resistance and Current Measurement System
DC Resistance and Current Measurement System including: 6622A Series Bridge, 6634A Temperature Stabilized Resistance Standards, 6664C Scanner(s), world’s most precise and stable 6623A Precision Current Source/Range Extender, Wired Equipment Rack, and Bridgeworks Software.
-
product
cPCI Backplanes
CompactPCI bus is compatible, in terms of electrical specification, with the PC world’s PCI bus. The mechanical specifications were adapted to the commonly used Euro-board plug in systems for 19" racks.
-
product
Load Cell Indicators
Procter & Chester Measurements Ltd
The instrumentation will power the load cell. The mV/V signal coming back from the load cell is converted by the indicator and displays the force in a unit (e.g.: Kg, kN, lb – customers choice). The indicator will need to be mounted in to a case or control rack for safe use.
-
product
Signal Conditioners
General Purpose
Encore offers a complete line of General Purpose Signal Conditioning instrumentation to meet even the most demanding requirements. Packaged as interchangeable two-channel plug-in modules, Encore’s broad product line includes frequency to voltage converters, strain gage amplifiers, accelerometer conditioners, digital voltmeters and DC power supplies. All of our systems feature a common CAL input on the rear of the rack which allows for calibration of the entire rack. Calibration function varies based on the modules installed. For example, the Model 633 applies a shunt calibration resistor across the bridge, while the Model 149 applies a reference charge source to the input. Contact Encore today and let our team of design engineers help you determine which of our products is best for your application.
-
product
DC-AC Inverters
The standard DC/AC inverters start at 125VA and rise to redundant modular systems capable of a 48kVA output. All our inverters give a true sinewave output and have proven themselves to be exceptionally reliable in numerous applications. Our DC/AC power inverters are provided in a variety of different case styles from wall mount, benchtop to modules, cassettes and 19" racks. A number of inverters can be built and approved to railroad and automotive standards. Stand-alone units are complimented by DC/AC inverters with built-in bypasses. The INV-TC3P is capable of providing 3-phase generation from a 48VDC supply.
-
product
Hot Swap, Fault Tolerant, Ultra Reliable Power Supply
Series HSP
The Kepco HSP series provides mission critical power. HSP comprises a group of twelve models, eight 1000 watt power supplies with outputs from 3.3 volts to 125 volts and four 1500 watt power supplies with outputs from 24 volts to 125 volts. All models feature current-sharing for parallel redundant N+1 operation. Models with the or-ing diode, option R, are capable of hot swapping when plugged into Kepco¹s RA 60 series rack adapter. Models with a digital meter, option M, are also available (see photo, right). A mechanical keying scheme allows the user to define which power supply will plug into a specified slot in the housing. Output voltage and current limit settings are adjustable from the panel and may be remotely adjusted.
-
product
Integrated Receivers/Demodulators/Bit Synchronizers
Lumistar provides a wide variety of rack mount integrated receiver and diversity combiner systems. Some of these can be configured with multiple receivers, diversity combiners, and bit synchronizers depending on custom requirements. Lumistar does not manufacture any computers, but selects only the finest of the industrial machines available to provide a high performance package. Basic system setup, control, and display software is included with each of these systems at no additional cost.
-
product
1200W Single Channel 19", 1U, Rack Mounted DC Power Supply
T3PS062001P
1200W Single Channel 19", 1U, Rack Mounted DC Power Supply.
-
product
19" Enclosures for 6U VME VPX Boards
R4U8S
The R4U8S is a 4U height 19'' Rack Mount Industrial Chassis featuring 8 slots of either VME or cPCI 6U size boards. The R4U8S has successfully passed the mechanical, thermal, electromagnetic EMC/EMI qualification tests required by our customers. Its modular design enables to fulfil the requirements of application areas ranging from the environmentally benign right through to deployed industrial, airborne and naval applications.
-
product
VME64x 7U 84HP 17 Slots
Hartmann Electronic’s 17 slot 19” rack mountable VME solution – The VME64x 7U system. This VME chassis comes with two 400W cPCI hot-swap power supplies with vertically oriented card slots. This platform conforms to VITA 1.1-1997 while providing a high capacity yet practical packaging solution for high-performance processors.
-
product
Receiver, 9025, 25 Module, Slide Mount, Telescopic Handle - Left Side
310104498
The 9025 is a 25 module receiver designed to fit into a standard 19" rack. This model is equipped with a telescopic handle on the left side. This handle is designed to rest flush against the side of the receiver as a standard handle, or can be extended out to the left up to 3" to accommodate a larger ITA enclosure or other obstruction that may prevent normal handle operation/ engagement.As with the standard 9025, a microswitch is included. Mounting flanges and an instrument bracket are also included for slide mounting. A slide kit is required, but not included. See 9025 procedure sheet/ user manual for instructions on choosing the correct slide kit length for your test rack. *Please note: Consult procedure sheet/user manual for information regarding slight slide mechanism bracket protrusion downward into next U height on test rack on both sides of receiver.
-
product
Electronic Design
We design and build custom racks, special switching systems, RF systems and custom Digital/ Analog sub assemblies. The hardware can be packaged per your requirements, using industry standard modules, rack mounted instruments, or custom made packaging. Extensive LabVIEW, embedded and other programming languages development are available as part of our hardware control support.
-
product
Rack Mount Hawk/PC Chassis
9381
A slide-in replacement for a Nova/Eclipse. A 10.5 inch (267 mm) high chassis with a 5-position Nova/Eclipse backplane and card cage, 450 watt power supply, cooling and rack slides. Accommodates up to five DG-compatible 15" x 15" (381 x 381mm) boards, a PC motherboard, diskette drive and up to three visible half-height disk drive bays and one internal half-height drive bay.
-
product
IP / VoIP Analysis & Simulation
GL offers high density Ethernet/IP tester variant which includes mTOP™ 1U/2U rack mount enclosures within which PacketExpert™ portable USB units are stacked to provide high density GigE ports form factor solution for testing GigE switches, routers and network conditions.
-
product
Quantum Laser Systems
By combining the Optical Frequency Comb and multiple ultrastable frequency stabilized lasers in a transportable, rack based system Menlo Systems offers a complete laser system for most demanding applications like optical clocks, quantum computing, and quantum physics experiments based on cold atoms, molecules and ions. The customer can configure the system in terms of laser wavelengths, laser power and frequency accuracy so that it is optimally matched to the application.
-
product
Rack Mount Kit For CX3300 Series
CX1903A
The Keysight CX1903A rack mount kit for the CX3300 series lets you easily stack your CX3300 mainframe in a rack.
-
product
6TL23 Off-Line Seat Operation Base Test Platform
H71002300
The 6TL23 is a bare rack for creating Off-Line, modular, flexible and reliable Base test platforms. The overall rack capacity is 18U (580mm depth). The rack is ideal for sit-down operation, since there’s space for the operator’s legs under the fixture receiver.
-
product
19-outlet power strip
PO-1968
19-outlet power strip 15 Amp, 125 Volts. These rugged, versatile strips provide real convenience wherever multiple outlet strips are required. Can be used with racks, consoles, production lines and lab tables. Mounting hardware included.
-
product
3U Rack Mount Kit For Opt 1 CM
34193A
The Keysight 34193A (5063-9243) rackmount adapter kit is used to mount a single ½ module or two ¼ module width standard System II instruments 3U 132.6mm high instrument such as the Keysight E3631A to E3634A and E3646A to E3649A products.
-
product
Adjustable Isolating Transformers
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2235 is a 2 in 1 laboratory isolating transformer with integrated DC power supply, which was designed with the aspect of high safety requirements for use in research, science and repair. The device has a dual adjustable DC, AC output, which can also be used for constant voltage or current and offers high stability and performance. The output voltage or the output current can be read exactly on two separate 3-digit LED displays and the fixed output supplies a voltage of 5 V. The device is protected against damage by overload and short circuit by reliable overvoltage protection and can be placed in a 19 ”rack installed or used as a table device (“stand-alone”).
-
product
6-slot VXI Chassis
The 6-slot VXI portable rack is intended for use in modular measurement information systems based on the VXI version of the standard. The 6-slot portable VXI crate is designed to accommodate the system module, in the first slot and VXI instrumental modules placed in the remaining slots, to provide their electrical power supply, as well as to provide information interconnection via the VXIbus bus between the modules and with the control computer. The chassis meets the requirements of GOST R 51884-2002 and the document System Specification VXI-1 Revision 1.4.
-
product
VME 19" Rack Mount Industrial Chassis
R2U4S
The R2U4S is a 2U height 19'' Rack Mount Industrial Chassis featuring 4 slots of either VME or cPCI 6U size boards. The R2U4S has successfully passed the mechanical, thermal, electromagnetic EMC/EMI qualification tests required by our customers. Its modular design enables to fulfil the requirements of application areas ranging from the environmentally benign right through to deployed industrial, airborne and naval applications. All feature a door to better protect the electronics which is placed inside.
-
product
Parallel Testing of Multiple DUTs with High RF Channel Count
Test Rack UTP 7033 RF for validation
Our basic test rack UTP 7033 (33 rack units) is intended for equipping with various products and therefore for various application areas.The rack shown here as an example is prepared with products and measurement instruments to test automotive devices with high channel count.
-
product
PXIe Accessories
The PCIe Extension product family from Hartmann Electronic enables different components such as laptops, PCs, motherboards and backplanes to be used together in CompactPCI or PXI racks to communicate over PCI protocol.
