Radar Detectors
Monitor for rf and laser waves.
-
Product
Multi-spectrum IR Flame Detector
FL4000H
-
The FL4000H is an advanced multi-spectrum infrared (MSIR) flame detector that provides superior false alarm immunity with the widest field of view.
-
Product
SF6 Gas Moisture Detector
JH4000SF-1
-
Xiamen Jiahua Electrical Technology Co.,Ltd
SF6 gas moisture is not only a major item for gas quality acceptance but also a key index to evaluate installation, maintenance and operation of SF6 electrical equipments. In IEC60480-2004 Guidelines for the checking and treatment of sulfur hexafluoride (SF6) take from electrical equipment and specification for its re-use, moisture is listed as a detection item for SF6 fresh gas, equipment acceptance, preventive test and maintenance.
-
-
Product
SMART Sensor Gas Detector
IMR EX440
-
IMR Environmental Equipment, Inc.
The detector uses natural diffusion as the method to detect gas. It is constructed with high strength engineering plastics composites with an antiskid rubber housing. The detector is comfortable to hold, is water-proof, and dust-proof.
-
Product
Heat Detector Testing
Solo 423 / 424
-
Available in both 110 / 120 and 220 / 240 volt versions the Solo 423 and 424 are the professionals’ choice where cables and leads are acceptable. Unconstrained by energy availability they provide the quickest of test times and are, perhaps, most suitable for the highest temperature detectors.
-
Product
Radar Electronic Support Receiver
RR024
-
The RR024 is designed for Radar Electronic Support (RES) and Radar Warning Receiver (RWR) applications where high performance and small size are of prime importance, with filtering, amplification, detection and pulse parameter measurement being combined into one multi-function unit. Four amplitude measurement channels allow direction finding by amplitude comparison between adjacent antennas. An IFM, fed from one of the amplitude channels via an SPDT switch, performs 14 bits of frequency measurement on the selected input. Frequency resolution is nominally 1 MHz over a 2 to 18 GHz band.
-
Product
Gamma Detectors
-
In Gamma detectors, the gamma radiations produce electrons by interacting with the cathode material and the filling gas.These electrons ionize the gas and the charge carriers are collected by the electrodes. The resulting anode pulse is detected by a load circuit. The primary electrons are created by several interaction mechanisms:- Photoelectric effect- Compton scattering- Pair production
-
Product
Cable Detectors
-
PeakTech Prüf- und Messtechnik GmbH
This cable detector works acoustically and offers a quick and inexpensive solution to find voltage-free lines in the house installation, to test telephone lines, to identify individual cables / wires or to carry out a continuity test.
-
Product
HPGe Detectors & Spectrometers
-
Baltic Scientific Instruments, Ltd
Baltic Scientific Instruments produces gamma- and X-ray spectrometers based on HPGe coaxial or planar detectors with liquid nitrogen and electric machine cooling. The spectrometers are used for radionuclide analysis and for monitoring of activity in the nuclear industry and related environment monitoring. HPGe detectors have additional applications in scientific research and technology development as well as in various spheres of industry including security and border control.
-
Product
Dynamic X-Ray Detector
Shad-o-Box HS
-
The Shad-o-Box HS family of x-ray detectors are high-performance, high-resolution x-ray imaging devices designed for high speed digital radiography applications. Each model combines our x-ray sensor modules with appropriate readout electronics and a 14-bit digital interface for easy connection to a PC. The high-speed digital connection allows real-time imaging at frame rates up to 66 fps, while the state-of-the-art CMOS technology offers superb contrast, dynamic range, and resolution.
-
Product
Detector Testing
-
CI Systems' Optical Test benches are especially built to test many types of detector arrays used as the sensors of a camera, from visible to far infrared ranges. With CI Systems' expert know-how, these test benches can be tailored to a customer's design requirements. MTF, spectral response, crosstalk, NETD and sensitivity are some of the basic parameters that can be tested with CI's Optical Test benches during the design, manufacturing and integration of detector arrays.
-
Product
Open Path Infrared Detector
Ultima OPIR-5
-
Get continuous monitoring of methane, propane, and other combustible gases with this open path infrared detector. Provides 4-20 mA analog signals, as well as digital display and relay contacts.
-
Product
Ground Penetrating Radar
-
RD1100 and RD1500 both feature internal GPS and high resolution touch screens. For connectivity, both offer on-board Wi-Fi and a USB port. Additionally, the RD1500 allows users to create depth slices and review their locate path on screen while on site, and selectively enhance shallow/small, medium depth/size, or deep/large targets using the proprietary FrequenSee™.
-
Product
Safety Voltage Detector
289 SVD
-
Standard Electric Works Co., Ltd
● Bright LED visual indication● Audible indication● Mute function● AC voltage detection: 100Vac ~ 69kVac● Frequency range: 50/60Hz● Easy-to-prove method● Self-test function● Power source: 1.5V(AA) alkaline battery × 3● Non-contact detection by proximity● Personal sensor, easy to wear and convenient to use● Can be attached with hot sticks by optional accessory● Lightweight, robust and compact● Easy access to batteries Comply with EN 61326-1
-
Product
Fixed Gas Detectors
-
Crowcon offers a flexible range of fixed gas detection products which are able to detect flammable, toxic and oxygen gases, report their presence and activate alarms or associated equipment. We use a variety of measurement, protection and communications technologies and our fixed detectors have been proven in many arduous environments, including oil and gas exploration, water treatment, chemicalplants and steel mills.
-
Product
Utility Detection Radar
DS2000
-
There’s a lot going on underground that you need to know about before you ever start to dig. The Leica DS2000 Utility Detection Radar finds all potential threats, including non-conductive pipes and fibre optics, increasing safety by lowering the risk of accidently hitting underground assets. Increase safety, speed up work and lower asset management costs with the ability to prevent hazardous outages and collect more information. The DS2000 betters your business by making it safer, faster and more efficient.
-
Product
Radar Level Gauge
HRRD730 Series
-
HighReach Measuring & Controlling System Co.,Ltd
At The Radar Level gauge Antenna emits and Narrows at The Microwave Pulse. This Pulse propagates in Space AT at The Speed of Light. The When IT Encounters at The Surface of at The the Measured Medium, Part of the ITS Energy IS the REFLECTED the Back and Received by at The Same, Antenna. At The Time interval The Between the transmitted pulse and the received pulse is proportional to the distance from the antenna to the surface of the measured medium.Because the electromagnetic wave propagation speed is extremely high, the time interval between the transmitted pulse and the received pulse is very small (on the order of nanoseconds). It is difficult to confirm. The 90X series 26G radar level gauge uses a special demodulation technology To accurately identify the transmitted pulse and the time interval of the pulse is received to further calculate the distance of the antenna from the surface of the measured medium.
-
Product
Energy Detectors
-
Our pyroelectric energy meters cover a very wide range, going from nanojoules to several tens of joules per pulse. They also come in various sizes, from 8 mm to 95 mm in diameter and most of them are available with an optional attenuator.
-
Product
Resets And Voltage Detectors
-
ST’s reset and voltage detector ICs provide basic voltage monitoring (low-voltage detect POR-LVD function) and reset timing for power-on resets. These devices offer:
-
Product
SmartWireless Gas Detector
CXT
-
Teledyne Gas & Flame Detection
All component parts are rated for Class 1; Division 1, Group C, D hazardous areas. These advanced field devices consist of a CXT low power gas detection sensor and wireless transceiver packaged in a single enclosure. Power is provided by a disposable “C” cell battery pack capable of continuous operation for greater than 60 days. Additional power options include a Smart Rechargeble battery with a run time of 5-6 months, a disposable “D” cell battery pack with a run time of 9 months and solar panel providing continuous operation.
-
Product
Non-Contact Voltage Detector
VOLTCHEK
-
The VOLTCHEK is a variable non-contact voltage detector, A proximity device which detects the presence of an alternating electric or electromagnetic field. It is used by industry professionals for live or dead voltage determination of outdoor overhead or underground at URD test points. Firstly as a proximity device to determine live or dead situations and then as a touch device to verify the source has physically reached the zero AC field. This is the only equipment capable of testing all voltage from AC 415V to 765kV from a distance, beyond arcing zone.
-
Product
Active Bat Detectors
-
The all-in-one device designed for active bat detection and recording.
-
Product
Phase Detectors
CD series
-
The CD series is a phase detector module. It is possible to detect small level signal and signal buried in noise.
-
Product
Refrigerant Detectors
-
UEi Test & Measurement Instruments
Is designed and certified to meet the new tougher standards and detect the latest refrigerants.
-
Product
Servicing and Testing of Search and Rescue Radar Transponder
SART
-
The Search and Rescue Radar Transponder as a part of GMDSS is a subject to annual test during radio survey. The annual testing of SART is recommended due to SOLAS regulation IV/15.8.The purpose of an annual testing is to determine that SART is operational as defined in appropriate performance standards for Survival Craft Radar Transponders for use in Search and Rescue Operations, IMO Resolution A.802 (19).Also Marine Orders require that a radar transponder must be inspected, tested and have its batteries replaced at intervals specified by its manufacturer.
-
Product
Hazardous Area Gas Detector
Meridian
-
Teledyne Gas & Flame Detection
Whether you need an infrared or catalytic bead sensor to detect combustible gases or an electrochemical sensor for a toxic environment, the Meridian universal gas detector utilizes a single detector head to easily accept all sensor types. There is no requirement for distinct personality boards in the gas detector or different detector heads to make the instrument behave as a combustible or toxic gas detector. The Meridian gas detector accepts all sensor types in one detector. Simply attach the specific toxic or combustible sensor to the universal detector head and the Meridian gas detector will automatically determine the type of gas to be detected. Installation of the sensor is a simple plug-and-play action. At Teledyne Gas and Flame Detection, we are always looking to anticipate your future needs. We designed the Meridian gas detection platform to be future proof, allowing you to take advantage of new sensing technologies from Teledyne Gas and Flame Detection while maintaining ease of use and peace of mind.
-
Product
Multi-spectrum Infrared Flame Detector
975MR
-
The Rosemount 975MR multi-spectrum infrared flame detector is based on accurately analyzing the multi-spectral signals by utilizing three separate IR sensors. The 975MR detects fuel and gas fires at long distances. For example, this product will detect a 1 ft2 (0.1m2) gasoline pan fire at 215 ft (65 m) in less than 5 seconds. The 975MR also provides the highest immunity to false alarms and enhanced overall coverage range.
-
Product
Thermopile Detectors and Sensors
-
Our Thermopile Detectors are typically Thermopiles with integrated Thermistor providing analog output in various packages. Special designs include built-in lenses or reflectors to enhance sensing performance, Isothermal constructions, or Dual narrow-band windows. Our latest Thermopile Sensors include specially designed electronic circuitry to provide calibration, digital output, and functionality. With the DigiPile, Excelitas offers a unique design for measurement applications. With its digital output, this device does not require any low noise amplification. The CaliPile family provides integrated features that enable measurement, as well as presence detection applications.
-
Product
Leak Detectors
-
High sensitivity setting locates R134A leaks to 3gm/yearFlexible gooseneck probeEasy one handed operationAudible & visual indicatorsRubber sleeve protects detector & probe
-
Product
Stealth Laboratory/QA Metal Detector
-
Stealth Laboratory metal detectors are manufactured to suit any application. Designed to be used in offline product examination to assist in determining contaminant source. Stealth detectors use digital signal processing technology and have high sensitivity levels to ensure the detection of the smallest ferrous, non-ferrous and stainless steel contaminants. The built-in data collection software with USB data transfer establishes the Stealth as an effective critical control point complying with stringent HACCP regulations.
