Circuit Board
-
Product
SSMA Connectors
-
Pasternack SSMA connector category includes 52 part numbers, most are RoHS and REACH compliant. SSMA connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Pasternack SSMA connectors are built to precise microwave and RF industry specifications. Connectors in SSMA series are manufactured in male or female gender with 50 Ohm impedance. SSMA connector items are available in straight or right angle versions, as well as, bulkhead, 2 hole panel, 4 hole panel or mountless options. These SSMA connector designs include crimp/solder, solder, solder (without contact) or solder/solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this SSMA connector series is in-stock. Not just in stock, but these connectors will ship the same day as they are purchased.
-
Product
ASA200
-
The ASA200 Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software the ASA200 you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board. The built-in gate/bias generator (+/-10V, 100ohm source impedance) can be used to help test active components such as SCR’s, opto-couplers, small relays, TRIAC’s etc. An external dual footswitch can be connected to the ASA200 and can be user configured to control various functions.With the ASA200 we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at an affordable price.
-
Product
SMC Connectors
-
Pasternack SMC connector category has dozens part numbers, most of which are RoHS and REACH compliant. SMC connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. These SMC connectors are built to precise RF and microwave industry specifications. Pasternack connectors with SMC series are built in jack or plug gender with 50 Ohm impedance. SMC connector items are available in straight or right angle versions, as well as, bulkhead, 2 hole panel, 4 hole panel or mountless options. These SMC connector designs include clamp/solder, crimp/solder or solder attachment methods. as with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this SMC connector series is in-stock. In addition to being in stock, these connectors will ship the same-day as purchased.
-
Product
Riser
RISER-SUMIT-2
-
WINSYSTEMS’ RISER-SUMIT-2 boards are designed to provide extra space in a SUMIT stack. They are printed circuit boards (PCBs) with SUMIT mounting holes and bus connectors. They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
Product
Software
D2B
-
The unique capabilities of Teradyne's D2B software enable EMS and OEM manufacturers and partners to interconnect their global enterprises to optimize printed circuit board assembly test and inspection efficiencies early in the manufacturing / build cycle. D2B is a powerful suite of solutions that provides a standards-based architecture that supports GenCAM and ODB++ file formats enabling electronic manufacturers to outperform their competition, maximize profitability, and get to market first.
-
Product
High Flexibility Test Controller Card
TCC 1800-UE
-
The TCC1800-UE Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via Ethernet.The TCC1800-UE is designed to work with positive voltages up to 24V. The card provides extensive IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, ethernet-, CAN, USB, SPI and I2C interfacing.
-
Product
PCB Manufacturing
-
Printed circuit board assembly is the process of soldering or assembly of electronic components to a printed circuit board or PCB. Star Engineering is a full-service manufacturer of printed circuit board assemblies, providing complete solutions for all types of requirements. Being a skilled custom cable assembly manufacturer, our services include designing, testing, prototyping and manufacturing followed by complete support. We provide both surface mount (SMT assemblies) and through hole PCB apart from any custom requirements of your processes.
-
Product
Silicon Nails Feature, GTE 10.00p
K8214A
-
Keysight’s Silicon Nails feature enables all the tools required to develop and execute tests on non-compliant boundary scan devices that are connected to boundary scan compliant devices on the printed circuit board.
-
Product
Sixteen Channel, 12-Bit Analog Input Card
PCI-AI12-16(A)
-
Model PCI-AI12-16 is a multifunction, high-speed, analog-to-digital converter board for use in PCI-Bus computers. It accepts up to 16 single-ended or eight differential inputs. The board uses a low-noise, multilayer printed circuit board. Inputs are protected against overvoltage conditions up to ±35 volts and typically survive static discharges beyond 4000 volts.
-
Product
Switch Probes
-
A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.
-
Product
Inline test system for FCT, ICT, ISP and Boundary Scan for Automated Operation
LEON InLine
Test System
High production volume often requires inline solutions with fully automated product Handling – the LEONlnline is a complete Inline Board Test Solutions for printed circuit boards. It integrates a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors.
-
Product
Extender
3690-17
-
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
Product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
Tester
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
Product
Microprocessor System Tester
IST-6700
-
IST Information Scan Technology, Inc.
The IST 6700 is a low cost, stand-alone test instrument that provides a wide range of automatic and manual features for troubleshooting microprocessor-based circuit boards. It employs CPU emulation with low cost CPU personality pods to attach to or replace the resident CPU. With stored "Known Good" test data, the 6700 can provide fully automatic functional tests to check the system RAM, ROM, control signals, address, and data bus plus the measurement of the CPU clock frequency and supply voItage.
-
Product
At-Speed Non-Intrusive Functional Testing
ScanExpress JET
Functional Test
Functional circuit board testing presents many challenges that are often costly and time consuming. Most functional tests need to be customized for each design, limiting reusability. This results in software engineers vying for time between development code and test code. Even when functional tests become available, the diagnostic details are often inadequate to give clear visibility on a given problem.ScanExpress JET is a tool designed to overcome these challenges by automating the functional test generation process on CPU–based IEEE-1149.1 compliant circuit boards. Coined JTAG Embedded Test, JET is the preferred method for at-speed, non-intrusive functional testing.
-
Product
Expanding In-Circuit Capabilities
-
Circuit Check supports reading linear bar codes and 2D symbols within each of its fixture product lines.When spring-loaded probes are not practical or access is limited, Circuit Check can help you with thru-connector tests to contact connectors on any surface or edge of a circuit board. These tests can be implemented spring probes, mating connectors, sacrificial SMT connectors, and stabber cards.
-
Product
Semi-Rigid Test Probes Up to 6 GHz
-
Fairview Microwave’s semi-rigid test probe assemblies come in multiple cable diameters to help when attaching the unterminated end of the probe to a circuit board trace. There are two versions including straight-cut probe ends for those that would like to customize the dimensions of the center conductor and dielectric dimensions, as well as pre-stripped probe ends that are ready for immediate use. By soldering the outer conductor to the signal ground and the exposed center conductor to the trace carrying the signal of interest, simple sampling measurements can be made without having to create a separate subassembly circuit board or add a connector to the circuit layout which can take up valuable real estate. Fairview provides 3 diameters of semi-rigid coax and 3 different lengths from 3 inches to 12 inches to fit a variety of trace widths and applications. All test probes are 100% RF tested to ensure the cable assemblies operate to 6 GHz and also to make sure that the SMA connector interface meets the 1.35:1 VSWR specification prior to shipping. To protect the small diameter coax from damage, each part is shipped in a clear protective tube that can also be used for storing the probes for future use.
-
Product
Ceramic Process Carrier Pallets
-
Ceramic engineering specializing in Silicon Carbide, Boron Carbide, Alumina, Zirconia and Lead Zirconate Titanate (PZT) based ceramics, composites and thin films for High Strength, high temperature, semiconductive ceramic designed for use in wafer fabrication or hybrid circuits in vapor deposite ovens. Test Electronics will precision drill and customize pallets for your circuit board. Click on the Quote tab on the left then click on the Carrier Pallets tab to get an instant quotation on your process carrier pallets.
-
Product
Failure and Technology Analysis
-
Failure analyses in order to clarify the failure cause soonest possible.From single device to the whole system - and from highly complex IC up to printed circuit board (PCB), mounting & interconnection technology and printed board assembly (PBA).
-
Product
Adjustable Press Plate Bed of Nails Testers
Protector Adjustable Family
-
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
Product
PCIe Gen3 High Speed, Compact Camera for Testing
CB013MG-LX-X8G3
-
High speed, compact, fast camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.
-
Product
PXI-2536, 544-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-36
Matrix Switch Module
544-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2536 is a high-density 8x68 PXI matrix switch module that is ideal for routing low-power DC signals in validation test systems of mass produced devices such as semiconductor chips and printed circuit boards (PCBs). Featuring FET relays, the PXI‑2536 offers unlimited mechanical lifetime and switching speeds up to 50,000 crosspoints/s. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
Test Fixtures
-
Test fixtures are a product for the test and the testing of printed circuit boards. The test adapters offered by uwe electronic are suitable for both manual testing and automated testing with vacuum operation. The test fixture can be either fully equipped and wired or delivered without installed components. Pneumatic, Mechanical and Vacuum Fixtures.
-
Product
Visual Fault Diagnostics and Repair System
ScanExpress Viewer
-
ScanExpress Viewer™ is a printed circuit board (PCB) CAD data & photograph visualization tool for boundary-scan test development, electronic manufacturing test, and product repair environments.When combined with ScanExpress ADO™ (Advanced Diagnostics Option) for detailed results from ScanExpress Runner™, ScanExpress Viewer displays fault coordinates and connected traces superimposed directly on a board photograph or CAD layout diagram for expedient repair.
-
Product
Manufacturing Defects Analyzer
eloZ1-1600
-
The eloZ1 Manufacturing Defects Analyzer is an in-circuit tester of the very latest generation, reliably detecting connection and assembly faults on printed circuit board assemblies. The eloZ1 can be integrated into table systems as well as into inline-systems.
-
Product
Substrate Inspection Apparatus
-
The test system of the printed circuit board (mounting board) called the flying probe tester developed ahead of the world received high evaluation at the electronics manufacturing factory around the world, securing the top share of the industry and "Takaya of the board tester" We have established a firm position that.
-
Product
Flex Test Fixtures
-
FTFs are test fixtures which are dedicated for testing flex-based components and assemblies such as displays, touch panels and more. A weak spot in a typical functional test system is the method to connect DUT flexible cable to a circuit board where the simple method of attaching the flex directly with an ZIF or LIF connector fails.
-
Product
PCB Manufacturing
-
SO-9001 and UL certifiedClass IIIRigid circuit boards up to 40 layers3-mil traces and 3.5 mil spacesMinimum Mechanical drill size 8-milMinimum Laser drill size 3-milBlind / Buried ViasControlled ImpedanceRoHS Compliant (all options available)High temperature, high frequency materialAluminum and other exotic material
-
Product
75 Ohm SMC Connectors
-
75 Ohm SMC connector category from Pasternack contains dozens of part numbers, most of which are RoHS and REACH compliant. 75 Ohm SMC connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. These SMC connectors in 75 Ohm are built to precise RF and microwave industry specifications. Pasternack 75 Ohm SMC connectors are available in jack or plug gender with 75 Ohm impedance. SMC 75 Ohm connector parts are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm SMC connector designs include clamp/solder, crimp/solder or solder attachment methods. Like most of the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm connector series is in-stock. On top of being in stock, these connector in 75 Ohm SMC series will ship the same day as they are purchased.
-
Product
Test Fixture Kits
Test Fixture
More then ten years of experience in special, customized engineering and manufacturing brought us to the highest level of creating reliable, flexible and robust Test Fixtures. Currently our HQ is located in Vecsés, Hungary together with our R&D. Equip Group has Test Fixture Kit manufacturing plant in Serbia, focusing on supplying competitive, high – quality and high – volume products for the global market.With more then 180 employees, Equip – Test is able to offer our customers turnkey solutions in fixturing with test program generation. No matter if you have a simple or complex, high-density PCB (Printed Circuit Boards), or if you have DUT (Device Under Test) already assembled into metal or plastic housing, we can offer you a very stable technical solution.
