Pulse Amplifiers
increase amplitude while keeping waveform. Also known as: Pulsed Amplifiers
-
Product
RF Amplifier Modules
-
Analog Devices RF amplifier modules offer high linearity, low noise figures, and low phase noise, as well as low power consumption. These devices are all fully specified over frequency and temperature for use in a variety of applications.
-
Product
Pulsed Transmitter
-
Built to operate in harsh environments, the Pulsed Transmitter unit provides radar installation decoy protection in a compact footprint and is powered by a Dewey Generator.The unit is comprised of a power supply, power amplifier, signal generator and antenna, with a fiber optic command and control interface providing throughput speeds capable of 1.25 G bits/sec via 1310 nm, single mode, ruggedized fiber.
-
Product
VME PWM Servo Motor Driver / Amplifier Board
64PW2
Servo Motor Drive
NAI’s 64PW2 is a 6U VME Servo Motor Driver/Amplifier Board featuring a dual, four-quadrant, bi-directional, PWM servo amplifier. Specifically targeted for DC servo motor applications, this board has an amplified power stage that uses a Pulse Width Modulation (PWM) control signal to provide motor control for both brush and brushless motors. Each motor drive accepts a 65 VDC power input and provides a 5 Amp maximum continuous current output (8.5 Amp peak).
-
Product
Shunt Isolation Amplifier
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Especially to accurately measure large DC currents via shunt resistors, ie for making isolated detection of mV voltage on shunts. Variants with calibrated range selection. Working voltage up to 3600 V AC / DC.
-
Product
Pulse Adapter
CV30 P300
-
Frothingham Electronics Corporation
The CV30 P300 test station is the highest current 30KW pulser in a series of exponential pulse generators that can be connected to our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of high power exponential pulses. For exponential pulses up to the 10/1000, the station can produce 30KW, 1000A, or 300V whichever is the most limiting. The station can also include all of the usual FEC200 tests in the same test program.
-
Product
Bi-Directional Amplifier
-
RF Lambda’s bi-directional amplifiers can be used in repeater type applications where a single conductor is used for both receive and transmit. These amplifiers offer low noise figure and high linearity. Hermetically sealed options are available upon request.
-
Product
Reference plus Comparator or Amplifier
-
Analog Devices reference plus comparator or amplifier products combine the excellent initial accuracy and low overtemperature drift performance of single function voltage references with comparators, buffer amplifiers, and current sense amplifiers. These products offer compact solutions for a broad range of applications such as battery monitoring, threshold detectors, window comparators, auto power-off circuits, and low dropout (LDO) regulators.
-
Product
Modal Exciters & Amplifiers
-
Experimental modal analysis, or modal testing, is a process for physically obtaining a math model of a structure’s dynamic properties. Modal tests identify a structure’s modal properties: natural frequencies, mode shapes, mass, stiffness and damping. Modal test results help troubleshoot resonant excitation from operating forces, validate and verify finite element models, predict the benefits of structural modifications, support design verification, and understand structural responses due to complex loading conditions.
-
Product
MOSFETs For Amplifier
-
These are enhanced power MOSFETs with excellent frequency characteristics. They are ideal for audio amplifier output.
-
Product
Solid State Power Amplifiers (SSPAs)
-
CHANGSHA KAIYUAN INSTRUMENTS CO., LTD.
* Ruggedized for use in pulsed airborne, naval and ground radar* Found in weather forecasting Doppler radar systems* Utilized world-wide in air traffic control and precision approach radar systems
-
Product
Split type Pulse Current Sensor
CTF-05M
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Pulse current detection for power demand meter.*Through hole type CT.*Open collector output.
-
Product
JESD22-A115 Machine-Model (MM) Pulse Emulator
MM-10A
-
High Power Pulse Instruments GmbH
- Pulse unit to generate JESD22-A115 machine-model (MM) waveforms with TLP- Extremely stable and reproducible machine-model (MM) waveforms- Compatible with HPPI TLP-3010C/4010C/8010A/8010Csystems which have installed pulse width of 25 ns and rise time of 100 ps to 300 ps- Up to ±10 A machine-model peak current with TLP-3010C, which is equivalent to ±667 V (MM)- Up to ±15 A machine-model peak current with TLP-4010C, which is equivalent to ±1000 V (MM)- Up to ±30 A machine-model peak current with TLP-8010A and TLP-8010C, which is equivalent to ±2000 V (MM)- Same measurement procedure as TLP including DC test of the DUT- Compatible with HPPI TLP software and waveform data storage and management- 50 Ω SMA input and output connectors- Compact size: 61 mm x 25 mm x 17 mm
-
Product
Low Noise Op Amplifiers (≤ 10nV/√Hz)
-
Analog Devices’ portfolio of low noise (≤ 10nV/√Hz) op amps includes many amps with the lowest noise performance in the industry. These high speed, low distortion (1 nV or less) op amps enable better signal fidelity in the most demanding conditions, allowing system designers to achieve the lowest total system noise performance in applications with high source impedances. We feature a considerable variety of these amps with wide supply ranges and low power.
-
Product
Difference Amplifiers
-
A difference amplifier is a special purpose amplifier designed to measure differential signals, otherwise known as a subtractor. A key feature of a difference amplifier is its ability to remove unwanted common mode signals, known as common mode rejection (CMR). Unlike most types of amplifiers, difference amplifiers are typically able to measure voltages beyond the supply rails, and are used in applications where large dc or ac common-mode voltages are present. They are ideal for current and voltage monitoring. Analog Devices offers a range of difference amplifiers, optimized for low distortion, low power, or high voltage performance.
-
Product
Linear High Efficiency Power Amplifier
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Keylink's high efficiency linear power amplifiers are available for operating frequencies from 1MHz to1 GHz with output power from 1 to 100 watts. Combined with linear design, these linear power amplifiers provide ultra low distortion, suitable for multi-band, multi-mode communication applications. With built-in monitor circuits, Keylink's power amplifier assure consistent performance in terms of reliability. KeyLink's linear power amplifiers can be categorized as follows:
-
Product
Narrowband RF/Microwave Power Amplifier
-
While our broadband amplifier series are designed for multi-purpose, narrowband amplifier series may provide more appropriate solution for your specific needs. By narrowing the frequency range, smaller, lighter amplifier solution at more reasonable cost will be usually available.
-
Product
Pulse Function Arbitrary Noise Generator
81160A
Arbitrary Waveform Generator
Generation of 330-MHz pulses and 500-MHz function/arbitrary waveforms with a 2.5-GSa/s sample rate and 14-bit vertical resolution; Selectable crest factors for white Gaussian noise lets engineers determine how much distortion to apply to a device during stress testing to meet various serial bus standards; Glitch-free timing parameter changes allow engineers to change the frequency without drop-outs or glitches and enable continuous operation without rebooting or resetting the device under test; and Arbitrary bit patterns show capacitive load of the channels using simple pattern settings. Complex measurement setups are no longer necessary to test designs to their limits. Pulses 330 MHz, 500 MHz sine waves, 660 Mbit pattern
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
-
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
RF Amplifiers up to 1000 MHz
-
Narrow and Broad band high power RF modules and rack mount amplifier systems using solid state devices including LDMOS and GaAs in Class A and Class A/B topologies for Pulse, AM, FM, continuous wave and digital modulation applications that include EW, Radar, Jamming, EMI and EMC radiated immunity, and wireless communications testing.
-
Product
Universal Amplifier Heatsinks
-
A universal heatsink, which is designed and fabricated for Eravant's active device applications with up to 15-watt power dissipation. The heatsink consists of the main heatsink body, a DC fan and a heat spreader. The heat spreader is also known as adapter, which is used to bridge the mounting gap between the heat sink main body and the to-be-heat-sunk devices, such as power amplifier, frequency active multiplier, oscillator, transmitter and transceiver due to various mounting hole locations. The heat spreader offers various mounting patterns to accommodate more than 15 product models. This heatsink is not only designed for Eravant's standard products and Uni-Guide™ featured products, but also for many industrial standard microwave and millimeter wave products offered by other manufacturers. Other heatsinks with different power dissipation capacities are offered under different model numbers.
-
Product
Distribution Amplifier
-
AVLINK TECHNIC TAIWAN CO., LTD.
Is a device that accepts a single input signal and provides this same signal to multiple isolated outputs.These devices are important because they allow a signal to be distributed to multiple destinations without ground loops or signal degradation. They are used for a number of common engineering tasks, including multiple amplification, cable television, splitting monitor and front of house mixes, and "tapping" a signal prior to sending it through effects units to preserve a "dry" signal for later experimentation.
-
Product
Solid State GaN (Gallium Nitride) Amplifiers
-
Fairview Microwave’s solid state GaN (Gallium Nitride) power amplifiers (also called SSPAs) feature broad frequency bands ranging from 30 MHz to 7.5 GHz and very high gain levels from 43 to 60 dB. These GaN SSPAs also show impressive harmonic response (-15 to -20 dBc) under worst case conditions. Saturated output power levels range from 10W to 100W with 20% to 35% Power Added Efficiency (PAE). All of our high power solid state GaN amplifiers from Fairview have internally regulated single voltage supplies. Our GaN SSPAs are designed to withstand environmental conditions such as humidity, altitude, shock and vibration with an operating temperature ranges from -40°C to +85°C. Some models are also equipped with integrated heat sinks and cooling fans. Most designs are EAR99.
-
Product
Headphone Amplifiers
-
Applied Research and Technolgy
Drive in-ear monitors, tap a speaker line when a monitor isn't available, and make sure the whole band can hear everything they need.
-
Product
Ignition Pulse Detector
IP-3000A
-
IP-3000A Ignition pulse detector is a slim and light weighted detector by using amorphous metals fiber element. It is 1/4 in thickness (mass: approx. 1/50) and 1/3 in weight compared with the previous model of Ono Sokki. Also the IP-3000A can obtain constant output from low to high rotation with high sensitivity.Meeting the needs of structure or mechanism in recent gasoline engines, the IP-3000A can easily clamp around an ignition coil cable (the primary side cord of ignition coil or the current cord of electronic distributor). Moreover, heat-resistant design up to maximum operating temperature of +120 C° enables measurement under harsh environment.The IP-3000A Ignition pulse detector can be used with Ono Sokki’s engine tachometer.
-
Product
Microwave System Amplifier, 45 MHz to 50 GHz
83051A
Amplifier
The Keysight 83051A microwave system amplifier is a compact, off-the-shelf amplifier designed for systems designers and integrators. This amplifier provides power where you need it to recover system losses and to boost available power in RF and microwave ATE systems. The ultrabroad bandwidth from 45 MHz to 50 GHz allows the designer to replace several narrow bandwidth amplifiers with a single Keysight amplifier, eliminating the need for crossover networks or multiple bias supplies.
-
Product
Pulsed Eddy Current (PEC)
Lyft®
-
Lyft is a high-performance solution reinventing pulsed eddy current (PEC). The patent-pending Eddyfi® solution features:
-
Product
Dual Relay Trip Amplifier for RTD and Slidewire Sensors
SEM1633
-
The SEM1633 provides an accurate alarm / switching function when used with RTD or Slidewire sensors. Other sensor characteristics or your own 22 point linearization characteristic (for slidewire or linear resistance) can be downloaded into the product enabling you to adapt it exactly to your application.
-
Product
Electric Transducer Driver Amplifier
7620
-
The Krohn-Hite Model 7620 is a 17/34 watt, wideband power amplifier that offers extended output power and voltage capabilities. Performance features not available in other power amplifiers, the 7620 provides a differential output and is able to deliver 17/34 watts of continuous power (68 watts at dc) and 141V/282V rms (400V/800Vp-p). It can also provide plus and minus dc voltages simultaneously.
-
Product
Photo Detector with Integrated Transimpedance Amplifiers
ADN3010-11
-
Analog Devices optoelectronic amplifiers include a range of germanium photodiodes that, through a proprietary process, have been monolithically integrated with silicon transimpedance amplifiers and limiting amplifiers. This process eliminates the need for bond wires connecting the photodiode to the transimpedance amplifier, which leads to improved performance and greater manufacturing reliability. Our portfolio of products also supports the growing need for optical and electrical interface miniaturization.
-
Product
USB Power Sensor - 100 MHz to 20 GHz, Average, Peak (Pulse), Pulse Profile
GT-8555B
-
The Spanawave/Giga-tronics GT-8550B USB Power Sensors offer easy-to-use high-performance RF and microwave power measurement. High dynamic range and high accuracy make these sensors ideal for testing in wireless communication applications and Defense EW systems. The GT-8550B series feature a ruggedized body and fast measurement speed. These broadband power sensors provide easy-to-use, fast, accurate power measurement for R&D laboratory, manufacturing test and field installation and maintenance applications.
