Pulse Amplifiers
increase amplitude while keeping waveform. Also known as: Pulsed Amplifiers
-
Product
H2S Trip Amplifier Module
TA202A
-
The TA202A is a single-channel H2S Trip Amplifier Module for use with our H2S Intelligent Sensors. It is designed to monitor H2S in parts per million (ppm) levels and provide status indication and alarm outputs.
-
Product
Pulse Characterization Sensors
-
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables.
-
Product
Low-Noise Parametric Amplifiers
-
Insight Product Company offers Low-Noise Parametric Amplfiers based on Monolithic Integrated Circuits (MIC) in the frequency range of 30 to 100 GHz.
-
Product
Low Noise Amplifier
-
Corech Microwave’s Low Noise Amplifier(LNA) frequency ranges from 1kHz to 67 GHz, featured with ultra low noise figure, high gain and compact size. Narrow-band & wide-band ready modules are available. Output power from +1dBm to +18dBm. 2.92mm – F, PIN, and SMA – F connector options are available.
-
Product
Amplifiers - Solid State
-
PMI offers a full line of RF and Microwave Amplifiers that range from 250 kHz up to 50.0 GHz. Many options are available. If you do not see exactly what you require on this website, please contact sales@pmi-rf.com because we offer amplifiers designed and built to your specifications at catalog prices.
-
Product
High-Frequency Amplifiers
-
Tabor’s line of High-Frequency Amplifiers allows for a better, more advanced utilization of the already available digital outputs on some of Tabor’s arbitrary waveform generators.
-
Product
Isolation Amplifiers
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Unipolar and bipolar DC input signals 20 mV to 200 V and 0.1 mA to 100 mA calibrated range selection. Working voltage up to 1000 V AC / DC.
-
Product
Scaling Amplifier
SIM983
-
Stanford Research Systems, Inc.
The SIM983 Scaling Amplifier provides fine adjustable gain and offset control for analog signals. Both gain and offset are set with 3½ digits of resolution, and the signal path has more than 1 MHz of bandwidth.
-
Product
HyMPulse Pulsed Field Magnetometer
-
Metis Instruments & Equipment NV
Geometry independent M-measurement (patent pending): One probe fits all, no pole shoes per magnet geometry. Measure the actual magnet instead of a prepared standard size sample. Measurement of industrial shapes like segments, cylinders, bricks,... with one probe
-
Product
Transient Pulse Generator
8282-1
-
The Model 8282-1 Transient Pulse Generator was designed for screen room use in making conducted spike susceptibility tests. It provides all the waveshapes required by MIL-STD-461B/C and many other military EMI specifications
-
Product
MOSFETs For Amplifier
-
These are enhanced power MOSFETs with excellent frequency characteristics. They are ideal for audio amplifier output.
-
Product
E-Band Low Noise Amplifier MMIC
AWL-7186
-
The AWL-7186 is a 4-stage ultra-low noise amplifier that provides a noise figure of less than 3.5 dB, an output P1dB of +8 dBm, and an adjustable gain range of 15 dB. The MMIC features exceptional gain flatness and superior noise performance over a very wide bandwidth. It is implemented in 0.1 um GaAs PHEMT technology.
-
Product
Pulse Adapter
CV5P350
-
Frothingham Electronics Corporation
The CV5 P350 station is the first mid power pulser in a series of exponential pulse generators that can be connected to an FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of high power exponential pulses. For exponential pulses up to the 10/1000, the CV5 P350 can produce up to 5KW, 500A, or 350V whichever is most limiting. It can also test all of the usual FEC200 tests in the same test program.
-
Product
Isolation Pulse Transmitter
PA-330Z
-
The PA-330Z receives the square wave signals from the rotary encoder, and converts it to low impedance signals suitable for long distance transmission after wave-shaping and amplifying via photo couplers which provide isolation between input and output.A 12VDC external power supply is provided for use with the DC powered RP series encoder.The case is sealed construction which allows closely mounting to the encoder.
-
Product
Low Noise Amplifier
-
Low noise amplifier with a typical small signal gain of 22 dB and a nominal noise figure of 5dB across the frequencyrange of 90 to 110 GHz.
-
Product
4-axis Pulse Train Motion Control Modules
HSL-4XMO
Motion Controller
HSL-4XMO is an advanced 4-axis remote motion control module via HSL bus. Combined with HSL I/O and motion control modules, it can meet many requirements in machine automation (MA) field. HSL-4XMO offers two models - HSL-4XMO-CG-N/P and HSL-4XMO-CD-N/P. HSL-4XMO-CG-N/P is suitable for steppers and linear motors. HSL-4XMO-CD-N/P is suitable for servo motors with transfer cable. Except the advanced motion control library (refer to PCI-8164), ADLINK also provides two extra features for users. Motion Point Table Managements can let users assign the points into the module in advance. Then, users can issue command to continuously move the points without consuming CPU resource. Motion Script Download provides users a easy interface to program the application. With this script, the DSP inside HSL-4XMO can decode the file and execute itself.
-
Product
Wireless Pulse Input Transmitter Module
T24-PA
-
The T24-PA transmitter module collects and processes pulse related measurements, such as speed of rotation, proximity, flow and count, forming part of the T24 modular telemetry system. The data transmitted by the T24-PA can be received by multiple T24 receivers that include displays, handheld readers, analogue outputs, relay modules and computer interfaces.
-
Product
SparkFun Pulse Oximeter And Heart Rate Sensor
MAX30101 & MAX32664 (Qwiic)
-
The SparkFun Pulse Oximeter and Heart Rate Sensor is an I2C based biometric sensor, utilizing two chips from Maxim Integrated: the MAX32664 Biometric Sensor Hub and the MAX30101 Pulse Oximetry and Heart Rate Module. While the latter does all the sensing, the former is an incredibly small and fast Cortex M4 processor that handles all of the algorithmic calculations, digital filtering, pressure/position compensation, advanced R-wave detection, and automatic gain control. We've provided a Qwiic connector to easily connect to the I2C data lines but you will also need to connect to two additional lines. This board is very small, measuring at 1in x 0.5in (25.4mm x 12.7mm), which means it will fit nicely on your finger without all the bulk.
-
Product
Pulsed IV
AURIGA 4850
-
Pulsed IV (current-voltage) measurements have emerged as the preferred method of capturing current-voltage characteristics of active devices such as field effect (FETs) and bipolar junction (BJTs) transistors.
-
Product
Low Noise Amplifier
LNA
-
Teledyne Defence & Space (TDS) Low Noise Amplfiers (LNA) are designed to amplify very low power signals without degrading the signal-to-noise ratio.An amplifiers is designed to increase the power of both the signal and the noise however the Low Noise Amplifier is specifically designed to minimise the additional noise so important information should not be lost.
-
Product
Erbium Doped Fiber Amplifier
EDFA
-
EDFAs are based on the light amplification in erbium-doped fiber, which are optically pumped by means of 980 nm or 1480 nm light sources. In this way, the light of a larger wavelength within the C or L band applied to the input of the amplifier is amplified, thus widening the range of optical communication links. EDFAs typically operate in saturation and the average signal power determines the average gain. The dynamics of EDFA are unaffected by the sequence and dynamics of a digital signal or channel interaction in DWDM systems. As a result, multiple channels can be bundled within the total erbium spectral amplification bandwidth. However, the total average output power in both cases is determined by the saturation power of the specific EDFA.
-
Product
Microwave Power Amplifiers
-
Spanawave/Giga-tronics Microwave Power Amplifiers deliver outstanding performance and exceptional value. These ultra-broadband amplifiers have excellent pulse performance and modulated signal fidelity, ideal for testing in wireless communications, defense EW and radar testing and general purpose microwave laboratory applications. Have the power you need to overcome cable and switching losses, or to drive higher power mixers, detectors and very high power amplifiers.
-
Product
Semiconductor Optical Amplifier
SOA
-
Amonics SOA is a polarization maintaining optical amplifier with high fiber-to-fiber gain. It is designed for transmitter applications to increase optical launch power to compensate for the loss of other optical devices. The benchtop version incorporates a user-friendly front panel housing a LCD monitor display, key switch, power control knob and optical connectors. RS232 computer interface is also equipped on the rear panel. 1MHz with 10ns pulse width intensity modulation is available. The OEM module version is an ideal building block for OEM system integration, especially in optical communication network and CATV applications. It requires only a single +5V power supply.
-
Product
Amplifiers
-
Amplifiers from Analog Devices deliver both high performance and high value. These amplifier ICs combine circuit design, manufacturing process innovation, and applications expertise to create products that simplify signal conditioning design.
-
Product
Amplifiers, Splitters & Combiners
-
DEV’s RF Splitters, Distribution Amplifiers, or Dividers are used to distribute and amplify RF signals, to compensate for signal loss, and to provide redundancy paths to ensure maximum uptime.
-
Product
Pulse Current Generator Multi-Pulse Generator
-
Shanghai Guantu Technology Co., Ltd.
What is the difference between ordinary current and pulse current?The difference between ordinary current and pulse current: ordinary current is continuous and uninterrupted current.Pulse current is a current whose direction does not change and whose intensity changes periodically with time.
-
Product
Ignition Pulse Detector
IP-292/296
-
These detectors are electromagnetic induction type detector designed to detect the number of ignition pulses produced in the gasoline engines. The IP-292 pinches a primary cord (low voltage) and the IP-296 pinches a secondary cord (high voltage) of the ignition coil. The compact, light-weight and clip-on design of these detectors offer a simple and easy detection of the number of pulse. Since the detector and its cord are made of heat resistance materials, these models are not affected by the high temperature in the engine room. These detectors are used with the engine tachometers made by Ono Sokki. (AR-7240B, CT-6700, HT-6200, SE-1620, FT-2500 or GE-2500)
-
Product
Pulse - Generator
PG 01-2000
-
The test generator PG 01-2000 is suitable for insulation test and testing of the impulse withstand voltage of electrical and electronic electricity meters. The generator produce a standard pulse voltage waveform with 0,1 / 2000 μs.
-
Product
PHIL 4-Quadrant Power Amplifier
PAV5000
-
PAV5000 is the four-quadrant amplifier with high power applied in the semi-physical simulation power platform to analyzer the sensitive load, the equipment power adaptability, and the electric vehicle, etc. and provide the technical support and service on the power quality.
-
Product
8-Channel Amplifier and Low-Pass Filter Module
SCS-814
-
The SCS-814 and SCS-815 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-814) and 0.5Hz to 60kHz(SCS-815). Each of the SCS-814/SCS-815's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
