Switching
Controls consisting of a mechanical or electrical or electronic device for making or breaking or changing the connections in a circuit. (www.cogsci.princeton.edu)
See Also: Switching Matrix, High Voltage Switching, Switching Matrices, Multiplexers, General Purpose Switch
-
Product
PCI 16 Reed Relay Output Digital Interface
8003
-
The 8003 PCI digital I/O interface provides 16 Reed relay outputs provide high quality, long-life, low current (10 Watt maximum), dry contact switch closures. Reed relays are well suited for low-current applications. The relays are normally open, and close when energized. Writing a 1 to the proper port bit can individually energize each relay.
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
Transformer Turn Ratio Tester
KVBB-II
-
KV Hipot Power Test Equipment Co.,Ltd
KVBB-II Transformer turn ratio tester is used to check turn ratio of transformer, tap switch situation, whether transformer interturn is short circuit and transformer can run in parallel or not.
-
Product
High Voltage Switching Systems
HXV Series
-
HXV products are high voltage systems intened for Hi-pot / IR or High voltage switching. They can be configured to drive from 32 to 128 switch points per chassis and can be configured as multiplexer (1xN) or Matrix (NxM) configurations. Stand HXV chassis are used for signals up to 5000 VAC rms ( 7400 V peak ) and can carry up to 5 amps of current. Custom systems can be built up to 25KV. Most of the modules used in these systems are 1xN multiplexers or 2x4 matrix modules that can be combined to form larger multiplexers or matrices. Connector options for standard HXV include 5 way banaba jacks / binding posts, Shrouded Banana Jacks or SHV ( High voltage BNC) if you need to use a high voltage cable with a grounded shield for safety applications. Control options include 10/100BaseT Ethernet LAN, RS232, GPIB or optional manual control. Standard HXV systems use high voltage reed relays. Custom HXV systems up to 25KV use application specific relays and connectors from a variety of vendors based on required specifications.
-
Product
PXI MUX 2 Banks of 32 Channel 1 Pole
40-610-021-2/32/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
IGBT For IH
-
IGBT devices for induction heating (IH) (soft switching), recommended for 10 to 100 kHz frequencies, and not guaranteed against short circuit.
-
Product
PXI 4-Slot High Density 2A BRIC Matrix, 116x8 2-Pole (4 Sub-cards)
40-573-002-116X8
Matrix Switch Module
The 40-573-002-116x8 BRIC is part of a range of high density matrix modules able to switch up to 2 A at 240 VDC/250 VAC. They are available in 2, 4 or 8-slot sizes to suit most high performance matrix requirements, constructed using quality electromechanical relays for high switching confidence.
-
Product
AC/DC Current Clamp Meter
CM1000
-
Clamp opens up to 1 inch (25.4 mm). One rotary switch operation. Large 4 digit LCD display. AC/DC Voltage measurement up to 1000 Volt. AC/DC current measurement up to 1000 A. Relative measurement. One touch auto zero. Peak Hold Function. Data Hold Function
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 14-Bank 40GHz SMA-2.9
60-801-414
Microwave Multiplexer
The 60-801-414 is a 6-channel, 14-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass, Single-Mode, 9/125 Fiber, MU Connectors, With Interlock
42-860A-322-HI
Switch Module
The 40/42-860A-322-HI is a PXI/PXIe dual insert/bypass switch with MU connectors,, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
Bench Power Supply, Single, Programmable, 1 Output, 1 V, 20 V, 0 A, 5 A
72-8350A
-
The 72-8350A is a laboratory switch mode DC Power Supply ideal for service applications where tight voltage and current regulation are critical. Highly efficient switch mode design delivers outstanding performance from an extremely compact footprint. Unique separate output ON/OFF control allows voltage and current setting, with the supply output turned off.
-
Product
PXIe Microwave Relay, Dual SPDT, 26.5 GHz, 50 Ω, SMA, Failsafe
42-780B-532
Microwave Relay Module
The 40-780B-532 (PXI) and 42-780B-532 (PXIe) are dual failsafe SPDT 26.5 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
PXI 8 Slot BRIC 192x12 2A 1-Pole Matrix
40-597-106
Matrix Switch Module
The 40-597 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-597 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI Dual 2 Channel Fiber MUX SC
40-855-222-M
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass, Single-Mode, 9/125 Fiber, FC/APC Connectors, With Interlock
42-860A-022-HI
Switch Module
The 40/42-860A-022-HI is a PXI/PXIe dual insert/bypass switch with FC/APC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
PXI 8 Slot BRIC 232x6 2A 1-Pole Matrix
40-596-104
Matrix Switch Module
The 40-596 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 150VDC/100VAC. The 40-596 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI General Purpose 2A Relay Module 26xSPDT
40-131-201
Relay
These are low cost, general purpose electromechanical relay cards capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
Product
EBIRST 78-pin D-type Test Tool
93-006-001
-
The 93-006-001 eBIRST 78-pin D-type test tool is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Electronic Compact Pressure Switch (Pallect Pressure Switch)
PPE
-
mm.A compact trimmer setting type, three types of piping connections (R1/8, Φ6 plug, Φ6 one-touch fitting) and a dustproof/waterproof structure allow for flexible use.
-
Product
SP8T RF Pin Diode Switches To 12 GHz
-
Pulsar Microwave manufactures 8-way absorptive and reflective RF switches in single-pole 8-throw configuration. They fulfill broadband and narrowband requirements from 40 MHz to 12 GHz and handle 200 milliwatts input power. The SP8T switches have an isolation of 60 dB and switching time of 100 ns. Most models specify 1.6:1 or better VSWR at all ports. The SP8T switches operate on a power supply of +/- 5VDC and switching control is 0-5 TTL logic. The unit comes standard with SMA female connectors. Options for control are line drivers and decoders.
-
Product
LXI Microwave Multiplexer, SP4T, 9-Bank, 18GHz, 50Ω, SMA
60-803-109
Multiplexer Module
Our 60-803-109 is a 9 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
High 1.80 (51.00) - 12.60 (357.00) Switch Probe
TSP138-H100-3
Switch Probe
Current Rating (Amps): 10Average DC Resistance lower than (mOhm): 20Test Center (mil): 138Test Center (mm): 3.50Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,760Overall Length (mm): 44.70Switch Point (mil): 67Switch Point (mm): 1.70
-
Product
6U VPX – OpenVPX Backplanes
-
VPX is a broadly defined technology utilizing the latest in a variety of switch fabric technologies in 3U and 6U format blades. OpenVPX is the architecture framework that defines system level VPX interoperability for multi-vendor, multi-module, integrated system environments.
-
Product
Ultra-High Precision Motorized Vertical Stages
-
Model: KSAV Ultra-High Precision Motorized Vertical StagesKSAV1010/2030-ZF is new product, wedge vertical stage with.high-resolution, so many advantages: high-stability, high-load and capacity in vertical position,self-locking.applicatin filed: high postion precision,high load capacity,limited space and so onCharacteristic ◆Cross ball screw rail,precion ground ensure resolution, straightness,high load capacity, limited space◆small travel improve resolution◆stepper motor and DB9 interface, choose controller flexibility◆switches ensure safe when operate◆ planning other specification and size
-
Product
PXI 8 Slot BRIC Matrix, Solid State, 320x8, 1-Pole (10 sub-cards)
40-563B-121-320X8
Matrix Switch Module
The 40-563B-121-320x8 is an ultra high density 8-slot matrix module with 1-pole switching and is part of our range PXI BRIC matrices. They are available in 2, 4 or 8-slot sizes to suit high performance PXI switching requirements and are constructed using solid state switches.
-
Product
Single 8-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-013
Multiplexer Module
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexers. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
Product
VisualIMPACT Software
-
CEAST VisualIMPACT software is designed to control CEAST Pendulums and Drop Tower Series, manage tests and offer a user-friendly interface when using the Data Acquisition System. It records force and absorbed energy data related to impacts, visualizes and helps analyze the results and calculates resilience. The operator is guided through parameters setup by means of tables describing strikers and specimens that are filtered according to the test type and international standard selected. In the case of instrumented tests, many possibilities for data analysis and visualization are made available. The results are shown through comprehensive and customizable graphs and can be filtered by break type (only specimens with a selected break type are shown). Working with groups of test, the software performs a statistical analysis, and the operator can pick and discard single test results. Different measurement units can be selected. It is possible to print reports and to export data totally or partially. Recent improvements include the possibility to set a number of user profiles, including graphic settings, default printing options, advanced parameters for data analysis and so on, switching quickly from one another when looking at results. The introduction of a new Data Acquisition System (CEAST DAS 64K) in the Impact product line has also triggered a number of new capabilities for the SW, which is now able to process a more comprehensive calibration file for instrumented tups and hammers and manage DAS configurations with a wider range of data acquisition channels.
-
Product
Power Supplies
-
Rugged and Reliable: Power Supplies from Analytic SystemsAnalytic Systems' Power Supplies use switch-mode technology with powerful IGBT (insulated-gate bipolar transistor) switching transistors, ensuring reliability and efficiency at minimal size. In addition, our Power Supplies feature:
-
Product
PXI 4 Slot BRIC 150x4 2A 1-Pole Matrix
40-568-002
Matrix Switch Module
The 40-568 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 200VDC/140VAC. The 40-568 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
USB Controlled Multi-Function DAQ For ATE Education And ATEasy Training
GT98901 Series
-
The GT98901 Demo board is a USB controlled, cost-effective, multi-function PCB assembly. The module is completely self-contained and includes an LCD display, measurement and stimulus resources, digital I/O, relays, and switches – all of which can be accessed and monitored via the USB port using a SCPI command set via a USBTMC interface which supports the USB488 protocol. Power for the board is provided via the USB interface, providing a totally self-contained assembly which can provide users with a simple yet complete vehicle that replicates many of the stimulus and measurement functions associated with ATE systems. When combined with Marvin Test Solutions' ATEasy® Test Executive and Test Development environment, the GT98901 is the ideal product for creating and supporting ATE training and education applications.





























