- Pickering Interfaces Inc.
product
PCI Precision Resistor Card 6-Channel, 3Ω To 5.82MΩ
50-297-052
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Automatic Test System
Automatic Test system is the ultimate solution for power electronic testing. The system includes a wide range of hardware choice such as AC/DC Sources, Electronic Loads, DMM, Oscillate Scope, Noise Analyzer and Short /OVP Tester. This flexibility combined with its open architecture software platform-PowerPro III, gives users a flexible, powerful and cost effective test system for almost all types of power supply testing.
-
product
Configurable Functional Test System
ATS-5000
Maximize the uptime of your most critical electronics with the ATS-5000 Functional Test System from Astronics Test Systems. Deployed globally for more than 20 years, the newest version of this tester provides a configurable, affordable solution that delivers just enough test.
-
product
EOL RF Functional Test
AS652
With this RF test platform, integrable according to the specific needs of the product, we cover a very wide range of test needs with manual feeding.Ergonomics have been fully observed in the design, including the option of servo adjustment of the working height according to the operator.
-
product
Test Equipment
ST9020
Shenzhen Star Instrument Co., Ltd.
The ST9020 single-phase energy meter test equipment is full-featured and stable. Optional accuracy classes are 0.1 and 0.05. As divided by structure there are combined type, integrated type and auto wiring type. The meter test equipment is controlled via PC-based software. Choices of meter position are 6, 12, 24, 30, 48 and 60.
-
product
Long Term Test Kit
When long term electro-chemical tests (>1000 hours) are run to monitor the cell degradation at the cathode for example, it is important to avoid any contaminant in the gas flow rate.Inconel 601 flange equipped with alumina housing and alumina tube to feed the gas to the electrode during long term test (>1000 h)Typical poisoning is coming from the chromium contained in the steel tubing. The volatile chromium species (Cr6+) will flow into the cathode (with the air) and thanks to th...show more -
product
Microcomputer Three-phase Relay Test Set
Weshine Electric Manufacturing Co., Ltd
Given the diverse functional requirements of the grid’s protection system, testing capabilities require a new level of sophisticated test hardware and software with which to analyse the entire protection system’s (or individual protection component’s) operation in "real life" situations.
-
-
product
Test Probe Kit
69600
Kit includes 14 flexible test probes, long straight probe, piercing back probe, crocodile clip, 4mm circuit tester adapter and Deutsch spooned probe. The probes are designed to be used on popular Weather-Pack, Metri-Pack and Micro-Pack style connectors. The test probes are 5" in length and are flexible to help eliminate damage to the connector terminals that can result from testing with a standard test probe. The 4mm adapter allows conversion of some circuit testers to a 4mm banana connector, which provides a better connection. Kit comes in a pouch for storage.
-
product
Dual Nav/Comm Test Panel
TA-155
The Best Dual Nav/Comm Test Panel on the market today. This panel is designed to test the KX155/155A and KX165/165A radios specifically as well as others and will allow by the book testing of these units. The panel includes specific switching for testing the intercom features, providing unit configuration and audio isolation as required. This panel also incudes basic provisions to run a second Nav/Comm using the long time standard 8 pin octal connector. Monitoring of either current or voltage to either radio is also provided. Integrated or stand alone testing of your OBS or converter indicators is provided as well as the required test jacks. Click on picture for larger view.
-
product
Ball Pressure Test Apparatus
CX-Q03
Shenzhen Chuangxin Instruments Co., Ltd.
The Ball Pressure Apparatus is used to check the integrity of dielectric materials by exerting 20N force. The BPA10 is called out in IEC 60335, 60950, 61010, UL, CSA and European Norms. It is used to check the integrity of dielectric materials by exerting 20N force. The Ball Pressure Apparatus is made of stainless steel for long life. Since accelerated life procedures are used for this oven test, more than one apparatus may be useful for parallel testing.
-
product
Explosive Atmosphere Test
This test demonstrates that a part will not ignite while operating in an explosive ambient atmosphere. The tests are conducted at ground level pressure as well as reduced barometric pressures, in a closed explosion-proof chamber.
-
product
Electrical Test & Measurement Tester
Evolusys Technologies Sdn. Bhd.
• Polarity • Forward & Reverse Voltage• Forward & Reverse Current• Snapback/Thyristor• Open/Short measurement• Contact check (optional-apply for Keithley C series only)
-
product
Test Case Management System
Kiwi TCMS
The leading open source test case management system. *Efficiently manage test cases, plans and runs*Improve testing productivity & reporting*Integrates with popular issue trackers*External API interface*GPL 2 licensed
-
product
Test Compliance
MX CTS Series
AMETEK Programmable Power, Inc.
A growing number of electronic products manufactured today have to meet international regulatory requirements for emissions and immunity. This is particularly true for products sold in the European community as well as a growing list of countries in the Far East. The California Instruments MXCTS System provides a cost-effective test solution aimed at verifying higher power product compliance to a number of AC and DC related harmonized test standards. The MXCTS system offers many of the same features and capabilities of the California Instruments CTS Series product line already in use at many EMC labs around the world.
-
product
Multi-Interface Test Backplane
SKU-047-01
The Multi-Interface Test Backplane was designed to support hardware and software designers who need to be able to plug in boards with different interfaces (into the host computer).
-
product
DC Magnetic Flux Leakage Testing
ROTOMAT / TRANSOMAT Product Family
Foerster Instruments, Incorporated
With the new generation ROTOMAT DA and TRANSOMAT DA flux leakage test systems FOERSTER is setting new standards in continuous quality assurance of ferromagnetic steel tubes. The test systems enable the reliable detection of natural and oblique defects, regardless of their angle or length, in addition to standardized longitudinal and transversal defects. The miniaturization of sensors together with highly integrated electronic components dramatically increases the number of channels. This makes a...show more -
product
4 Station Endurance Test Setup for Thermostat of Iron
SCR ELEKTRONIKS have developed 4 STATIONS ENDURANCE TEST SETUP FOR THERMOSTAT OF IRONwhich is used for carrying out endurance test for thermostat of iron for the required amount of time It is very useful and handy in line testing on Mass production line as well as type Testing. It consists of Voltmeter, Wattmeter, Programmable Logic Controller( PLC ). The equipment continuously monitors faults like Contact weld and Contact Open. The other important feature is we can operate the panel in Auto Mode or Manual mode. User friendly operations make the equipment to be handled easier for any operator. This manual contains information about operating instructions and maintenance of the equipment.
-
product
Rack Based Test Solutions
Most equipment manufacturers and large enterprises prefer rack-based test tools as they are compact and higher density form factor solution for testing, monitoring, and troubleshooting network conditions. GL’s Multiple TDM Optical and Packet (mTOP™) rack enclosure can house any combination of USB based test equipment which are easily deployed and securely fixed to an equipment rack to provide extraordinary scalability to test switches, routers and end-to-end networks. These rack based pl...show more -
product
Vertical Shock/Bump Tester (Pneumatic)
HIACC Engineering & Services Pvt. Ltd.
The pneumatic vertical shock and bump test system features an advanced design with a high degree of performance and automation. The testes is easy to use and have low maintenance requirements.
-
product
Mag Lead w/Alligator Clips
138
*54" Test Lead Set *Mag Lead features a magnetic disconnect. *You can "stick" to any metallic ground or test point. *Time saving product - can substitute for alligator clips at metallic test points. *Now, when you need alligator clips, you've got them! *Fits almost all DMM's and hand held scopes. *Get the Mag Lead, it stays put and won't fall off!
-
product
Appliance/Tool Tester
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
• Touch Screen Interface• Windows® 10 Pro• High Reliability with Proven Design• Lowest Board Count In Industry• No Proprietary Circuit Boards• USB Interface – No I/O boards in Computer• Remote Control Software for Factory Diagnostics/Updates• Full Network Compatibility• Integral Statistical Reporting• Test Data May be Stored in Multiple Formats• Two Year Warranty on Electronics
-
product
Mission Processor
58U91-03
- +28 VDC input- 9 DC outputs at 600 Watts- Provides system EMI per MIL-STD-461- Continuous Background Built-In-Test (BIT)- Temperature monitoring- I2C communication
-
product
Current Tester
MIG1248
The MIG1248 is a current generator with wave shape 8/20. Maximum impulse current is up to 48kA supported by a 12kV impulse voltage making the MIg1248 ideal for testing large varistors. An intergrated test cabinet can accomodate test components up to 5cm cube.
-
product
PXI 8-slot BRIC Power Multiplexer, 3-Channel, 16-Pole (3 Sub-cards)
40-571A-201
The 40-571A-201 is a 3-channel, 16-pole 3 Amp Power Multiplexer and is part of our BRIC family. The 40-571A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
product
EBIRST 50-pin D-type To 2x8-pin Power D-type Adapter
93-005-236
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
USB Vector Network Analyzer
P937xA Streamline Series
Keysight’s P937xA Series is an affordable full two-port vector network analyzer (VNA) that dramatically reduces your size of test. You can control its compact chassis from an external computer with powerful processing capabilities.
-
product
Digital Serial Data Audio Interface
PIO-9216
For accurate testing of devices that use the I2S, Left Justified, Right Justified and TDM audio data formats.
-
product
Fuse Buddy PRO Test Kit
310
Great new tool with 3 interchangeable test functions. 1) 30 Amp MINI - Circuit Amperage Testing 2) 30 Amp ATC - Circuit Amperage Testing 3) 30 Amp All Purpose Amperage Testing *The new Fuse Buddy Pro Kit can read amperage draws on both ATC and Mini fused circuits up to 30 Amps. *As an added bonus, the Fuse Buddy Pro can be used as an all purpose amp meter with the included 30A test clips.
-
product
RF Signal Generators
The RF signal source mainly acts as a stable local oscillator signal in the test, or generates various types of modulated signals, and the two-tone signal is used for signal excitation, receiving sensitivity testing and other applications. When choosing the RF signal source, the frequency range of the signal output, power requirement size, modulation type, frequency stability, amplitude accuracy and many other factors needs to be considered.
-
product
PCI Based JTAG Controller
PCI-1149.1/Turbo
The PCI-1149.1/Turbo is a powerful PCI-based JTAG/boundary-scan controller that is used for testing and in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard.
