-
product
Cable Test Van
Titron
BAUR Prüf- und Messtechnik GmbH
Automatic cable test van. The BAUR titron is a new automatic cable test van designed for cable fault location and cable testing. The new generation of the high-performance cable test van is based on state-of-the-art technology and provides effi cient, safe and reliable cable fault location and cable testing.* New intuitive operational concept* Central, automatic system control* Top reliability and quality standard* Flexible in terms of technology and equipment
-
product
Motor/Generator Testers
Appliance motors are always evolving and the final testing of those motors gets more complicated every year. We build fully automated testers for domestic or offshore manufacturing facilities that can perform any amount of motor testing that you require with limited interaction by the operator.
-
product
Software Solution for Interoperability Testing
COMPRION Network Bridge
COMPRION Network Bridge provides a direct connection between (e)UICCs and back end servers. This way, remote administration scenarios can be processed in a lab environment independent of a real network or a network simulator. This makes the work of (e)UICC manufacturers, MNOs, SM-DP(+), and SM-SR providers easier. The test effort is reduced significantly, because there is no need for a network simulator and the testing limitations of a real or simulated network do not apply.
-
product
Acceleration Testing
The acceleration test is performed on a centrifuge to assure that material can structurally withstand the steady state inertia loads that are induced by platform acceleration, deceleration, and maneuver in the service environment, and can function without degradation during and following exposure to these forces. Acceleration tests are also used to assure that material does not become hazardous after exposure to crash loads. The acceleration test method is applicable to material that is installed in mobile platforms such as aircraft, helicopters, aerospace vehicles, air-carried stores, ground-launched missiles, trains, ships, automotive vehicles, etc.
-
product
Environmental Testing
DATASYST Engineering & Testing Services, Inc.
Simulate real-world environmental conditions to know how your product or component measures up. DATASYST evaluates how your product responds to environmental stressors, including temperature, thermal shock, humidity and altitude.
-
product
Altitude Chambers
ESPEC can provide custom-built chambers for simultaneous testing of temperature and low-pressure altitude conditions. Two common applications are: Testing of avionics or other aerospace equipment to simulate actual conditions it might experience. Simulation of high-altitude conditions like might be found in mountainous regions.
-
product
Electrical Contacts Test
The electrical contact testing is performed to determine the reliability of equipment under various contacting conditions. A few types of electrical contact tests are: contact-chatter monitoring, contact resistance, intermediate, and low level contact switching.
-
product
Test Programming
TestAssistant II
From a front-end graphical user interface to a back-end relational database, TestAssistant II organizes and maintains everything necessary for testing. Tester interfaces, wires, connectors, adapter cables, and other complex sub-assemblies are graphically represented.
-
product
Three-Phase Testing
CMC 310
The CMC 310 is specifically designed for basic three-phase testing of protection and measurement devices. It is operated by the CMControl P software which runs on the CMControl P unit, a Windows PC or on an Android tablet. Its intuitive user interface and the test tools included are optimized for quick manual testing in the field.
-
product
CMK Mechanical Kits
Columbia has created a unique mechanical click system using ball bearings and guiding sleeves. The UUT is connected to the spring contact pins that are connected to the testing environment in a completely linear fashion. Connecting the UUT to probes can be approached both from the top and the bottom and, optionally, even from the side. The ergonomic housing provides generous space for additional measuring electronics. The back and bottom of the housing can be adapted to the various test system interfaces.
-
product
Advanced Handheld Partial Discharge Detector for Electric Power Equipment with Multi-Sensor and Cloud Diagnostic Technologies, Data Management Software, and Test Management App
PDetector
Power Monitoring and Diagnostic Technology Ltd.
The PDetector is an ideal device for On-Line Partial Discharge (OLPD) testing of MV and HV equipment which employs all 5 types of OLPD sensor technology: Ultra-High Frequency (UHF), Acoustic Emissions (AE), Ultrasonic, High Frequency Current Transformer (HFCT), and Transient Earth Voltage (TEV). The information from multiple sensors gives the PDetector the versatility to detect all types of PD in all types of substation apparatus. The exact type of PD activity can be determined effectively using...show more -
product
Optical Calibration
PIMACS which acquired the Korean Laboratory Accreditation Scheme(KOLAS) provides calibration service for your developments & products with a wide range of light measurements, traceable to international standards. We also supply the various optical calibration systems to the customers who want to acquire the qualifications of an optical testing laboratory.
-
product
Oven Data Logger
215
Memory stores up to 260,000 readingsIdeal for testing for powder or liquid coatings in batch or conveyor ovensVariable measurement interval, date, time, °C / °FHigh temperature resistant teflon coated probe cables are easy to clean after each runQuick display shows maximum temperature, Cure-Index figure and pass/fail for each probeMeasure up to 6 different temperatures at one timeIdeal in situations where powder coated thickness is inconsistentStart and stop logging at a pre-set temperatureLarge menu-driven display for easy operationPrint full colour report directly to any HP printerUSB data output to ElcoMaster® software and combine with other key inspection measurements
-
product
Online Tree Testing Software
Treejack
Take the guesswork out of information architecture with Treejack – the usability testing tool you can use to test your IA without visual distractions. Treejack helps you prove your site structure will work before you get into interface design. Tree testing is a usability technique for evaluating the findability of topics in a website. It’s also known as ‘reverse card sorting’ or ‘card-based classification’. Tree testing is done on a simplified text version of your site structure – without the influence of navigation aids and visual design.
-
product
Stator Testing System for EV Motor
EVT531
Shanghai Dean Electrical Co., Ltd
To meet the standard test projects requirement of the international companiesTo control and analysis the programs will reduce the human careless and misjudgmentEasy to edit environment and easy to learnIt can test multiple sets of DUTs simultaneouslyWhen there are several DUTs are tested, it could identify the undesirable sets individuallyThe Impulse/Surge with waveform comparison is a non-destructive analysisPolarity testMaximum saved files will be up to 100 setsIt provides the password functionSpeeding test could save time and improve efficiencyChinese and English pages can be arbitrarily switched
-
product
Intelligent Tangent Delta Tester of Enamelled Wire
TD-8S
Shanghai Dean Electrical Co., Ltd
·Tangent Delta Tester is used for testing the curing degree of enamelcover. The curve variation of tgδ shows the curing degree of enamelled wire directly, then adjust the heating temperature of enameling oven, to get a optimal curing degree of enamelled wire, control the wire quanlity effectively.·The temperature class of enamelled wire can be tested rapidly; the enamel type of wire can be determined preliminarily.
-
product
BTS Software
Shenzhen Sinexcel RE Equipment CO., Ltd
Sinexcle-Re BTS software is a backend control system designed for battery charge and discharge testing. It is suitable for various scenarios and test types, primarily encompassing three modules: battery test monitoring, process editing, and data analysis. The software strictly executes tests according to customer simulation requirements, providing highly customized testing solutions to meet personalized testing needs. It automatically generates the necessary test data reports, enabling quick and efficient product analysis.
-
product
FCC/CE Certification Testing
FCC/CE Certification Testing services to ensure that our product designs meets the necessary FCC/CE/UL norms. FCC compliance testing is mandatory for a wide variety of products designed for the EU/US markets.
-
product
Torque Gauges
Mark-10 torque gauges and torque testers are accurate and feature-rich torque measurement products ideal for a wide range of torque applications. All torque gauges and torque testers capture the peak torque in both directions (CW and CCW) and have selectable units of torque measurement. Torque capacities are available from 10 ozFin full scale to 5,000 lbFin, depending on the torque gauge or torque tester. Units may be handheld or used with a test stand and gripping fixtures to create a complete torque testing solution. All torque gauges and torque testers carry the CE mark.
-
product
Tachometer Tester
Series 1921
The Model 1921 Tachometer Tester is used for the testing and calibration of electrical and mechanical tachometer generators and indicators.
-
product
PCI Strain Gauge Simulator Card, 6-Channel, 350 Ohm
50-265-016
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
EMI and EMC Test System
EMI receiver system. It is a main test system for EMI (Electro Magnetic Interference) testing. The EMI-9KB is produced by the full closure structure and strong electro-conductibility material, which has high shielding effect. Due to the new technology for the EMI Test System, it solved the instrument self-EMI problem.
-
product
Whole Body Vibration Analysis
Whole Body Vibration (WBV) testing is a type of vibration analysis geared towards estimating the effects on the operator. There are three categories of concern for the operator, health and comfort, perception, and motion sickness. The goal for any WBV test is to ensure that under normal operating conditions there is no significant or lasting effect of the vibration experienced by the operator.
-
product
Impulse Test Equipment
mpulse test equipment for testing of low-voltage rotator windings.The equipment is composed of a surge impulse generator circuit, phase selector unit (selection between U, V and W), and waveform recorder circuit to provide a differential method type of impulse testing instrument.
-
product
ACP Portable Electrical Current Transformer Test,CT/PT Analyzer
Chongqing Assen Power Equipment Co., Ltd
ACP portable Current transformer analyzer is mainly used for field or lab testing, it can finish the measurements (M) and protection (P) class CT, PT and TYP class CT. Adopt 7 inch touch TFT LCD, self-equipped mini type printer supporting field printing; supporting to use USB flash disk to dump data. The CT PT Analyzer is the most complete and easy-to-use testing system for protection and metering CTs according to IEEE and IEC standards.
-
product
MPI Testing Solution
Since 2008, MPI’s LED tester has provided optical and electrical measurements. With mass production experience, tester functions include flexible recipe management, accurate calibration, and statistical analysis. Flexible configurations allow the customer to choose test equipment configurations from the spectrum meter, photo detector and source measurement unit in accordance with your specific requirements. With accurate controlling of each instrument and intelligent data analysis, our testers offer the most accurate measurement result for a wide variety of optical devices.
-
product
Engine Test
The engine test bench is a facility used by engine manufacturing plants to validate internal combustion engines before fitting to the vehicle. OEMs perform ‘Hot’ or ‘Cold’ testing operations in order to measure several physical variables and to diagnose any failure of parts or components. Jackmark Engineering provides bespoke rugged electrical test connection leads suitable for the industrial environment of petrol or diesel engine testing.
-
product
Shaker Systems
Vibration Research Corporation
Small force vibration testing equipment and shakers for product and modal analysis testing. Each system consists of a shaker and a matching linear direct-coupled power amplifier. Additional components may be added to the basic system to tailor it to your specific needs.
-
product
Multi Function Automobile Tester
6522
Peaceful Thriving Enterprise Co Ltd
The multi-function automobile tester has LCD display to indicate the measured result. It has polarity detection with the LEDs for a positive and negative indication of DC voltage. For auto use, the functions included the measurement of DC voltage and current, signal frequency and max/min voltage, resistance, temperature and power providing testing.
-
product
Test Compliance
CTS Series 3.2
AMETEK Programmable Power, Inc.
The CTS Series is a complete, turn-key compliance test system for EN IEC 1000-3-2 (Harmonics) Including A14, EN IEC 1000-3-3 (Flicker) and various EN IEC 1000-4 AC immunity tests. Consisting of an AC power source, a power analysis conditioning system (PACS) and a PC based data acquisition system, the CTS provides a complete turn-key solution for IEC testing. The Windows™ based CTS software performs the IEC tests and generates detailed test reports. Comprehensive data files are stored on disk to allow post test analysis.