-
Product
High Voltage 50 Ω Pulse Generator
TLP-4010C
-
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±10 kV*High pulse output current up to ±40 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
Product
Handheld Singlemode Multimode OTDR
XHO5000
-
X-50OTDR is manufactured with patience and carefulness, following the nationalstandards to combine the rich experience and modern technology, subject tostringent mechanical, electronic and optical testing and quality assurance; inthe other way, the new design makes X-50 more smart and compact andmulti-purpose. Whether you want to detect link layer in the constructionand installation of optical network or proceed efficient maintenance andtrouble shooting, X-50 can be your best assistant.
-
Product
Intelligent Automatic Touch Screen Control Oxygen Index Meter
-
Shanghai Dean Electrical Co., Ltd
1. Full-color touch screen control. You only need to set the oxygen concentration value on the touch screen, and the program will automatically adjust to the oxygen concentration balance and sound prompt.2. The step proportional valve is adopted to greatly improve the accuracy of flow control, and the closed-loop control is adopted to automatically adjust the oxygen concentration drift program back to the target value during the test, which avoids the disadvantage that the traditional oxygen index tester cannot adjust the oxygen concentration during the test and greatly improves the test accuracy.
-
Product
Electric Vehicle
-
Chroma Systems Solutions, Inc.
EV Automotive and Battery Test Advancements
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR228x-15/15
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,46 kg
-
Product
S2 Ultra High Sensitivity Sensors
ULP-S2 UHS
LED Sensor
Universal LightProbe S2 Ultra-High Sensitivity Sensors are designed for the test of very dim LEDs, as low as 0.01 mcd minimum, and including very low light-level LED-illuminated action-indicator switches, controls and status indicators for night/dark viewing in automobile interiors. Recommend the use of wide-aperture stainless- steel encased Fiber- optic Probes with contacting tips.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. long.Typical response times: <190mSFiber-Optic Probes: Wide-Aperture Fiber-Optic Probe recommendedDesigned for the test of very dim LEDs, as low as 0.01 mcd minimum
-
Product
Laser Test Systems
-
Santa Barbara Infrared, Inc. offers an extensive family of test systems and components that test and characterize the performance of laser range finders, designators, illuminators and spot trackers.
-
Product
Photonics Module Test System
58625
Test System
Chroma 58625 provides characterization testing for 3D sensing illumination devices. various test modules are combined for validation testing under precise temperature control.
-
Product
Test Boxes/Launch Boxes
-
Whether they are called a launch box, pulse suppressor, or launch cable they all do the same thing. When technicians conduct a quality test to look for fiber optic cable breaks and light loss in your installed network you need to eliminate what is called the "Dead Zone". When testing fiber optic cable with an Optical Time Domain Reflectometer (OTDR), these launch boxes eliminate the "Dead Zone". Without a launch box it is difficult to measure the relative loss at the near end and far end of the patch panel connections.
-
Product
Analytical Reference Materials & Standards
-
Agilent, now with former Ultra Scientific, offers a comprehensive portfolio of analytical standards, reference materials and certified reference materials for environmental, food safety, elemental analysis, instrument calibration, tuning mixes, and more.Reference materials and certified reference materials are substances that are tested to be homogenous and have fixed values of its concentrations. These standards are a critical component of your application workflow - from sample prep, instruments, columns, supplies, and services. The success of your analysis depends upon the quality of your reference material. All Agilent standard reference materials have been manufactured to the highest quality in an ISO 9001, ISO 17025 and 17034 accredited facilities to ensure the accuracy of your analyses.If you need a custom reference material, partner with us to design and develop a custom standard to your specifications.
-
Product
PITOT STATIC TESTER
ADSE 745
-
The ADSE 745 caters fully for all aircraft types and the different electrical power supplies.It can be used for testing high performance civil and military aircraft, fix and rotary wing. The multi-pressure outlets option can suit the more complex pilot-static-systems. This Pitot Static Tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems.
-
Product
FPD Tester Power Module
67393-120-480
Power Module
The 67393-120-480 FPD Tester Power Module is a new generation of small, stable, high reliability AC to DC power supply. It adopts compact mechanical design and uses Chroma FPD Tester for signal input/output that can provide a total solution for testing the signal, control and power of diversified panels.
-
Product
Motor Test Instruments
-
The absorbed energy of the DCE series Dyno is converted into heat in two rotors located at the external side of the coils . The rotors are designed with curvilinear cooling fins for fast dissipating heat into the atmosphere . This design provides with the smallest physical size for air cooled Eddy-Current Dyno . Simple construction and desirable speed-torque characteristics are adaptable to most of the applications.
-
Product
Colorimeter
Model CA-600
-
Teledyne Analytical Instruments
The CA600 is an online sequential sampling analyzer, using colorimetric methods. The analyzer can be configured to most laboratory colorimetric tests in individual processes.The CA600 Analyzers are easy to start up and use, simply connect the sample, waste and reagent lines and then power up the factory calibrated analyzer. Wall mount hardware is standard but an optional bench-top stand with reagent holder is also available. Accessing information for customizing an analysis routine is easily accomplished with the simple, user friendly menu structure and touch screen interface.The analyzer has two separated enclosures with two lockable doors. The top enclosure, called the electrical enclosure, includes the main power supply, the controller PCB assembly and the touchscreen interface. The bottom enclosure, called the liquids enclosure, includes all the components involved in the sample and reagent flow, mixing and reaction stages (sampling pump, reagent micro pumps and colorimetric reaction cell). Numerous analysis configurations can be programmed, depending on the accessories and the number of micro-pumps mounted in the liquid enclosure.
-
Product
I-V Measurement Systems
-
The I-V Curve Data Acquisition includes a fixture for holding cells for testing (see Figure 1 below). This fixture can accommodate cells from small to up to 100 mm x 100 mm. Adjustable cell stops, in the X & Y-axis, are provided to consistently locate the cells for testing. Two micro-manipulators are provided as shown in Figure 1. Each micro-manipulator has two spring loaded contacts to allow 4-wire measurement even for cells that have top contacts only. Two back-side voltage contacts are embedded in the Plate (galvanically isolated from the Plate) and make good electrical contact when the cell is held down by vacuum to the plate. All voltage and current probes are gold-plated. The cell is held down with vacuum during testing (built-in vacuum pump).
-
Product
Test Device for Bicycle Batteries
ATGF 1500/PBG
-
The ATGF 1500 is a multifunctional testing instrument for bicycle batteries and accompanying battery chargers. The easy to use ATGF 1500 is suitable for battery systems of Derby Cycle, Gazelle, Simplon and ZEG. est programs: Quick Test, Capacity Test, Recalibration.
-
Product
Automatic Transformer Test System
TH2829CX
-
Changzhou Tonghui Electronic Co., Ltd.
Number of Test PIN: 20 ■ Frequency: 20Hz-1MHz, Resolution: 0.5mHz ■ Signal Level: 5mV-2Vrms(Option:2mV-10Vrms) ■ Test Speed: max. 13ms ■ 7-inch TFT LCD display with a resolution of 800×RGB×480
-
Product
Continuous Wave Solar Power Meter
-
The OAI Continuous Wave Solar Power Meter is an essential analytical tool for measuring the irradiance (in Suns) of Continuous Wave Solar Simulators. OAI’s Solar Power Meters feature unique features not found in other Solar Meters. This versatile meter can display a wide variety of cell characteristics that include: cell type, window type, cell size, and temperature measurement device type. The OAI Continuous Wave Solar Power Meter can sample and display a continuous reading or peak reading. The Power Meter connects via USB port for data collection, and includes desktop software. With this small, portable, battery-powered meter, numerous production solar simulators can be tested and compared in a short amount of time, leading to greater production line consistency and throughput.
-
Product
Discharge Test System
-
The automated testing equipment automatically performs charge and discharge of energy devices such as the rechargeable batteries(cells, modules, packs) that are installed in PHV/ EV and mobile devices, while measuring the voltage, current, temperature, and impedance.
-
Product
Automated Testing
IRWindows™5
-
IRWindows™5 from Santa Barbara Infrared is an advanced software tool that automates the setup, execution, data collection and results analysis for industry standard performance testing of infrared, visible and laser systems. IRWindows™5 is the most advanced commercially available IR/EO sensor test software package in the industry today. It operates under Windows™ OS and is delivered installed on a high-end PC computer platform with frame grabber(s) selected to support UUT video formats. It is also available as a software only package. IRWindows™5 combined with SBIR target projectors provides test engineers and technicians a turnkey, automated hardware/software solution for full-spectrum sensor testing.
-
Product
Open Flanges Test Rig
-
Flexible cell dimensions: cells of Ø 8 to Ø 80 mm (or square till 70x70 mm) can be successively installed Quick start of experiment: less than 20 minutes to remount a new cell with different dimension, thanks to the simple design without sealing Other SOFC components: the open flanges test rig is also useful for conductivity measurements (electrolyte, electrode material, interconnect etc.) and sealing tests End of broken cells and secure testing: the cell is squeezed by a soft alumina felt that prevents any damages, the excess fuel burns continuously in the alumina felt at the cell edges
-
Product
Certified By SANBlaze
-
With the Certified by SANBlaze program NVMe SSD Manufacturers can run a series of automated tests to determine if their drives are running correctly and that they are complaint with the latest specs. Alerts of Failures or Warnings are shown if one or more drives is not behaving the way that it should, allowing for the quick diagnosing of any problems before the drives go out into the field. The Certified by SANBlaze tests are bundled with the software when customers purchase a Gen 4 SANBlaze SBExpress-RM/RM4 or an SBExpress-DT4 desk top unit. You simply choose the tests you want to perform, add them to the test bed, and click Start. The Certified by SANBlaze software does the rest, reporting the results in real-time and in beautifully created reports.
-
Product
Power Circulation Type Tire Wear Tester
-
This test machine is a tire wear test device that employs an electric servomotor power circulation system.
-
Product
Modular Source/Measure Units (SMU)
E5260A + E5270B
-
Keysight's modular source measure units (SMU) – E5260A and E5270B – combine versatility and advanced features to optimize testing costs. A variety of price-performance points and the framework to add up to 8 plug-in SMU modules enables a customized solution that can expand as your needs change.
-
Product
Chemical Emissions Testing
-
Underwriters Laboratories Inc.
As a global leader in the science of safety, UL evaluates products and materials to determine their impact on indoor air quality and, by extension, human health. Whether your products need to meet the emissions requirements of environmental certifications or regulations or you simply wish to have a better understanding of your products'''' potential impact on the indoor air for legal or risk assessment purposes, UL is your partner for developing healthier, lower emitting products.
-
Product
Mini-Test Station
-
Mini-Test Station for low current fuel cell testing. The test station includes Analog mass flow controllers for Anode and Cathode gas streams, humidity bottles with preheaters and temperature controllers and a cell temperature controller. The test station is designed to use the customer's Potentiostat to load the cell. Manual backpressure is provided for pressures from 0-60 psig. The Mini-Test station is basically our Analog Mass Flow Controlled Low Flow Humidification System with all the options.
-
Product
Line Tester
CAT 1 TEST
-
Monacor International GmbH & Co.
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
Product
LM-79 Moving Detector Goniophotometer
LSG-5000
-
Moving Detector Goniophotometer completely meets LM-79 Clause 9.3.1 and EN13032-1 clause 6.1.1.3 goniophotometer type 4 requirements. The LSG-5000 is an automatic light distribution intensity 3D curve testing system for measuring light. The measuring distance is from 5m to 30m. It can measure all types of lighting sources, LED or HID luminaires such as indoor and outdoor luminaires, roadway luminaires, street lamps, flood lights and other kinds of luminaires.
-
Product
Contamination Detection and Analysis
-
Contamination testing, detection, analysis, troubleshooting and resolution expertise to minimise downtime, maintain customer confidence, for quality & safety
-
Product
Portable Small Meter Tester
-
The Portable Small Meter Tester (PSMT) is a lightweight system for field testing of 5/81 in. meters. It includes a test meter with control valves, hose connections, fittings and pressure gauge. Meter tests can be done without removing them from service. The inlet control valve ensures an accurate test start and stop. A globe valve downstream from the meter allows flow rate adjustment during test. Connection to the PSMT is made using standard 3/4 in. male hose connections located on the exterior of the case. Two 3/4 x 39 in. metal-reinforced flexible hoses are provided for easy field connections.
