Transmission Electron Microscopes
image a beam electrons through a thin specimen.
See Also: Electron Microscopes
-
Product
Transmission Line Pulse Testing
-
Transmission Line Pulse testing, or TLP testing, is a method for semiconductor characterization of Electrostatic Discharge (ESD) protection structures. In the Transmission Line Pulse test, high current pulses are applied to the pin under test (PUT) at successively higher levels through a coaxial cable of specified length. The applied pulses are of a current amplitude and duration representative of the Human Body Model (HBM) event (or a Charged Device Model – CDM – event in the case of Very Fast TLP, or VF-TLP).
-
Product
Soldering Inspection Video Microscope
MS-1000
-
The MS-1000 is a highly portable microscope for exclusive use with BGA, CSP, and QFP. It is highly efficient in inspecting portions which cannot be inspected by the X-ray inspection method.Specifically, it is efficient for inspecting the following conditions: fillets of soldered balls, melted condition of soldered parts, cracks, defective soldering, etc.
-
Product
Electronic Loads
-
PeakTech Prüf- und Messtechnik GmbH
Can be used for important test procedures in quality assurance as well as e.g. testing of power supplies and control units, batteries, fuel and solar cells. For precise load control for various purposes, this device offers load control according to constant voltage (CV), constant current (CC), constant load resistance (CR) or constant power (CP) with a highly precise resolution of 1mW, 1mV, 1mΩ and 1mA. The device also offers additional test modes, e.g. the battery test or the dynamic test. The PC interface and software offer the option of implementing freely programmable test sequences with data evaluation.
-
Product
High Power DC Electronic Load
IT8800 Series
-
IT8800 series has wide power range 150W~10KW, voltage and current measurement speed up to 50KHZ, resolution up to 0.1mV/0.01mA, adjustable measurement current rising speed 0.001A/us~2.5A/us, built-in RS232/GPIB/USB interface. IT8800 series has wide application fields because of its high performance products, it has been applied to LED lighting, aerospace, automotive electronics and other fields.
-
Product
Semiconductor / FPD Inspection Microscope
MX61L
-
Motorized Microscope for 300mm dia. Wafer/17 inch Glass Substrate use Reflected/Transmitted Illumination.
-
Product
150 Watt Electronic Load Module
N3302A
Load Module
The Keysight N3302A is a 150 W (0-30A, 0-60V) electronic load module for use in either the N3300A or N3301A electronic load mainframe in system applications. The N3302A load module is fast and accurate, for programming in constant current, constant voltage, or constant resistance modes, or for making voltage, current or power measurements. The N3302A can also digitize waveforms.
-
Product
Light Sheet Microscopes
-
Life science research can place high demands on your imaging capabilities: Sometimes you need to image whole living model organisms, tissues and cells as they develop. Or you may want to observe subcellular dynamics in living samples over hours and even days. Light sheet fluorescence microscopy (LSFM) with its unique illumination principle is ideal for fast and gentle imaging of such specimens.
-
Product
Electronic Compact Pressure Switch (Pallect Pressure Switch)
PPE
-
mm.A compact trimmer setting type, three types of piping connections (R1/8, Φ6 plug, Φ6 one-touch fitting) and a dustproof/waterproof structure allow for flexible use.
-
Product
Standardize Production Test Software For PCBAs And Electronic Devices
test
The vast majority of test project man-hours are spent on software development, so the choices that teams make in software tools and architecture have significant impact on deployment schedules. Standardizing software across a team or organization increases both efficiency and proficiency, lowering the risk of missed deadlines and improving test quality and reliability. Test software must:
-
Product
Portable Microscope, X4001mm Field Of View, 1µm High Resolution
-
The highest resolution digital field microscope. Ideal for observing plant and animal samples at the cellular level. The ioLight microscope will even display limited structure in blood cells, which are 5-10µm across.
-
Product
Field-installation Type Ammonia Nitrogen Meter(Four-Wire Transmission)
HC-200NH
-
HC-200NH is an ammonia nitrogen(NH4-N) meter using ion electrode method which is designed for aeration control in wastewater treatment.
-
Product
10Ch Electronic Potentiometer 8 Bit
YAV90084
-
The YAV90084 can work autonomously as a 10Ch electronic potentiometer of 8 bit resolution. By default, it features 10kOhm resistors), but other resistor values can be assembled under request.
-
Product
Electron Probe Microanalyzer
JXA-8530FPlus
-
JEOL commercialized the world's first FE-EPMA, the JXA-8500F in 2003. This highly regarded FE-EPMA has long been used in various fields, such as: metals, materials and geology in both industry and academia. The JXA-8530FPlus is a third-generation FE-EPMA that comes with enhanced analytical and imaging capabilities. The In-Lens Schottky field emission electron gun combined with new software provides higher throughput while maintaining high stability, thus allowing a wider range of EPMA applications to be achieved with higher resolution.
-
Product
Modular Infinity Microscope (MIM)
-
Applied Scientific Instrumentation
ASI Modular Microscope components consist of tube lenses along with adapters and accessories that either are primarily used in the collimated light space or adapters that are to be used on the image side. Collimated light adapters use the 38mm diameter C60-RING system to connect components. Focus-side adapters attached to lens tubes with either a 30mm diameter coupling to the I.D. of the C60-TUBE, or with a 50mm coupling on the O.D. of the lens tube.
-
Product
Auger Electron Spectroscopy (AES)
-
Rocky Mountain Laboratories, Inc.
Auger Analysis, Auger Electron Spectroscopy (AES or Auger) is a chemical surface analysis method. AES measures the chemical composition of the outermost 100 Å of a sample. Measurements can be made at greater depths by ion sputter etching to remove surface layers.
-
Product
Multi-channel DC Electronic Load
IT8700 Series
-
IT8700 series programmable DC electronic load adopts removable modules design, supports up to 16 channels with mainframe extension transient mode up to 25 kHz, which improves your test efficiency, with high resolution and accuracy. Users can freely choose in the 8 load modules according to the number of channels and power requirements, controlled by mainframe control panel, or controlled by host computer software via built-in LAN / RS232 /USB / GPIB interface.
-
Product
Electronic Outside Air Temperature
OAT
-
The outside air temperature sensor is an electrical component that complements the control of a modern heating system.
-
Product
Electronic Loads
-
AMETEK Programmable Power, Inc.
Electronic loads have found a variety of applications ranging from power converter testing to current modulation. A large range of power sources can be tested using an electronic load from converters, inverters and UPSs to electrochemical sources such as batteries and fuel cells.
-
Product
Portable Spectrophotometers For Light Transmission
-
Portable and benchtop spectrophotometers for measuring light transmission in the full visible range in-situ. Due to the innovative approach of mutual correction, these measurements are also possible in ambient light.
-
Product
Load Cell Software And Electronics
-
Custom electronics and load cell software are viable low-cost solutions for OEM applications. With custom load cell software our customers can have exactly what is needed for the application and leave out the sometimes confusing extras that most off-the-shelf products have. We also offer private labels, overlays, and splash screens that will show your company's information on the display.
-
Product
Microscope Platforms
-
Applied Scientific Instrumentation
ASI Modular Microscope components consist of tube lenses along with adapters and accessories that either are primarily used in the collimated light space or adapters that are to be used on the image side. Collimated light adapters use the 38 mm diameter C60-RING system to connect components. Focus-side adapters attached to lens tubes with either a 30 mm diameter coupling to the I.D. of the C60-TUBE, or with a 50 mm coupling on the O.D. of the lens tube.
-
Product
Modular DC Electronic Load LED Simulator
6310/A
-
Chroma Systems Solutions, Inc.
Chroma 6310A Programmable Electronic Load integrates microprocessor capabilities into each load module and mainframe to provide simple and accurate parallel operation to optimize the speed and control among multiple load modules. All load modules may be configured to work synchronously, to test multiple outputs simultaneously, thus simulating real life applications.
-
Product
Atomic Force Microscope
XE7
-
Park XE7 has all the state-of-the-art technology you've come to expect from Park Systems, at a price your lab can afford. Designed with the same attention to detail as our more advanced models, the XE7 allows you to do your research on time and within budget.
-
Product
Field-installation Type Dissolved Oxygen Meter(Two-Wire Transmission, Membrane Type)
HD-300
-
HD-300 connects the DO (Dissolved Oxygen) sensor (DO-1100) and measures the DO in the sample water.The measurement method is membrane type polarography method. It is suitable for monitoring DO in wastewater treatment or aquarium for aquaculture.
-
Product
High Power DC Electronic Load
63200A series
-
The 63200A series high power DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more. The 63200A series have three operating voltage choices, 150V, 600V & 1,200V, with models covering power levels from 4kW to 24kW and up to 2,000A in a single unit. The DC loads have unique user defined waveform (UDW) capability and external analog modulating input for s imul a t ing re a l-wor ld, cus tom waveforms. Another distinct feature is the dynamic auto-frequency sweep function, which enables detecting a UUTs worst case output deviation across a wide range of current frequencies. In addition, a 255-set of data storage function has been built in for recall of the stored settings at any time. For automated testing, the save and recall functions can save a great deal of time.
-
Product
Cathodoluminescence Solutions for Electron Microscopy
CLUE Series
-
HORIBA Scientific's Cathodoluminescence Universal Extension enhances any SEM’s analytical capabilities while maintaining its original functionality. Since the sample is able to remain in the same spot, CLUE can easily be combined with other microscopy applications, such as EDS and EBIC.
-
Product
Drive Controller Function Test – Universal Functional Test System for Industrial Electronics
Functional Test
General functional test system based on LXI instrumentation for high mix / low to medium volume manufacturing. DUTs are tested which are mainly used as communication and measurement modules in power plant technology, grid management and electrical drives.
-
Product
DC Electronic Load
3310G Series（75W~400W）
-
Each 3310G Series module has its own control and display panel, CC / CR / CV / CP / Dynamic modes, plug in 3302G / 3305G / 3300G mainframe with 150 sets Store / Recall memory which provides load set-up more efficiently, also can be controlled via RS232、Ethernet、USB and GPIB interface.
-
-
Product
High Current Probes (Power Electronics) HCF77512A300U500HP
1030816
-
The High Current Probes (Power electronics) HCF77512A300U500HP provide exceptional performance and durability tailored for rigorous applications in power electronics. With an ability to handle continuous currents of up to 50A and a temperature range from -45°C to +200°C, this probe is designed to meet modern electrical engineering demands. The robust construction features a beryllium copper plunger with a gold plating, ensuring superior electrical conductivity and resistance to corrosion.
