Transmission Electron Microscopes
image a beam electrons through a thin specimen.
See Also: Electron Microscopes
-
Product
Electronic Load Mainframe GPIB
3300 Series
-
A 4 Channels 1200W Mainframe which accepts up to four Load Module.
-
Product
Field-installation Type Turbidity Meter (Four-Wire Transmission, For Wide Range)
HU-200TB-W
-
HU-200TB-W is a turbidity meter developed to continuously measure turbidity in processes with large turbidity changes, such as water intake and sedimentation tanks in water supply plants. It employs transmission 90-degree scattered light method and is ideal for monitoring changes in processes with large turbidity changes from low range (10 degrees) to high range (2000 degrees). An electric wiper cleaning can be installed as an option, and long-term stable measurement is possible by periodic cleaning.
-
Product
Infrared Microscope
DDR200/300 NIR
-
The McBain DDR200 NIR (for 200mm) and DDR300 NIR (for 300mm) provide high-speed defect detection and precision measurement on wafers and other parts. These cost-efficient systems offer unique advantages for both production and process development use, providing an optimum near-infrared (900-1700nm) solution when both subsurface defect detection and dimensional metrology are required.
-
Product
AFM Atomic Force Microscope
FM-Nanoview 6800
-
Zhengzhou Nanbei Instrument Equipment Co. Ltd
All-in-one design, smart structure and shape.Scan head and sample stage are designed together, strong anti-vibration performance .Precision laser detection and probe alignment device make laser adjustment simple and easy.Adapt servomotor to drive the sample approaching tip manually or automatically, to realize precision scanning area positioning.
-
Product
Field-installation Type Residual Chlorine Meter (Four-Wire Transmission, Rotating Type)
HR-200RT
-
HR-200RT is connected to a residual chlorine sensor (RA-30), which allows the free residual chlorine concentration to be measured with high accuracy. It is sutable for waterworks, pool water sterilization, and desalination systems. The measurement method is a three-pole polarographic method, which enables continuous monitoring of residual chlorine concentrations without using reagents.Stable measurement over a long period was realized by physical polishing cleaning using beads.
-
Product
1800~3000W DC Electronic Loads
JT633 series
-
Nanjing Jartul Electronic Co., Ltd
JT633 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT633 series load very suitable for testing power supply when produced in large quantity. Besides, JT633 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT633 series load satisfing most of R&D requirements.
-
Product
Fluorescence Microscopes
-
PicoQuant offers different solutions for time-resolved confocal microscopy. The available systems include single molecule sensitive microscopes with picosecond temporal resolution and super-resolution imaging capabilities as well as upgrade kits for laser scanning microscopes of all major manufacturers that enable time-resolved applications.
-
Product
Sequence Creation Software for Power Supplies and Electronic Loads
Wavy Series
-
WAVY is sequence creation software that supports the power supplies and electronic loads from KIKUSUI Electronics Corp.
-
Product
PXI Electronic Load Module
Load Module
PXI Electronic Load Module provides the electronic load capabilities of sinking DC power with high-accuracy measurements in a compact form factor optimized for design validation, characterization, and production test.
-
Product
DC Electronic Load
3110 Series（250W~700W）
-
Each 3110 Series stand-alone load has its own control and display panel, CC / CR / CV / CP/ Dynamic modes, also can be controlled intranet via RS232 and USB interface.
-
Product
Digital Microscope Accessories
-
Variety of extra accessories , such as macro lenses, remote control consoles, illuminations, image/video capture, software, stands and stages are available for Inspectis digital microscopes.
-
Product
FIBER OPTIC MICROSCOPES
SpecVision
-
SpecVision is a video probe that engages directly with Krell polishing machines. This permits the viewing of polished optical surfaces while connectors or bare fibers are still loaded in the polisher. This in-line video inspection technique minimizes material handling and potential damage/contamination that may occur when transferring components from the polisher to a traditional microscope. SpecVision can interface with Scepter, SpecPro and Rev Polishers.
-
-
Product
Wide Range Medium Power DC Electronic Load
N6200 Series
-
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N6200 series is developed based on NGI's years of experience in testing for power supply and battery. It is with high accuracy, high reliability and high cost-effective. N6200 series is with high power density and elegant appearance, which is available for benchtop use or installation in 19 inch cabinet.
-
Product
Imaging Mass Microscope
iMScope QT
-
Inheriting the concept of a mass spectrometer equipped with an optical microscope from the iMScope series, the iMScope QT is also Shimadzu's flagship model for MS imaging with a Q-TOF MS(LCMS-9030).
-
Product
Programmable DC Electronic Load
-
Programmable DC electronic load is a device that precisely regulates the load voltage and current dissipation power consumption of electrical energy. There are several important parameters to consider when choosing programmable DC electronic load, including maximum power, maximum current, maximum voltage, current slope, and so on. Each indicator is related to the needs and applications we actually test.
-
Product
Strap-Down Electronic Compass - for Commercial, Industrial, and Military Users
Revolution LP
-
The Revolution™ LP is a strap-down electronic compass designed specifically for commercial, industrial, and military users. The Revolution LP will be of particular interest to ROV and AUV manufacturers who are concerned with power usage and accurate heading in all types of challenging conditions. In standby mode, it draws a mere 50 μA and requires only 15 mA in run mode. It provides accurate heading data in less than a tenth of a second from wakeup. An extended range tilt sensor is available that allows for +/-60° of pitch and roll.
-
Product
Field-Installation Type ORP Meter (Four-Wire Transmission)
HO-200
-
HO-200 connects ORP sensor and measures ORP and temperature in the sample water. It is suitable for neutralization reaction treatment management of aeration tank, denitrification tank, etc.
-
Product
Transmission Line Probes
-
Transmission line probes are a special type of passive probe designed for use at very high frequencies. They replace the high impedance probe cable found in a traditional passive probe with a precision transmission line, with a characteristic impedance that matches the oscilloscope input (50 Ohm). This greatly reduces the input capacitance to a fraction of a picofarad, minimizing the loading of high frequency signals. A matching network at the tip increases the DC input resistance. While they have lower DC input resistance than a traditional passive probe (usually 500 Ohm) to 1kOhm), the input impedance of these probes remains nearly constant over their entire frequency range. A traditional /10 passive probe will have a 10 MOhm) input impedance at DC, however this impedance drops rapidly with frequency, passing below the input impedance of a transmission line probe at less than 100 MHz.
-
Product
ELECTRONIC MEGOHMMETER
MI-2550e
-
The MI-2550e general purposes megohmmeter is a truly portable equipment suitable to measure insulation resistances using test voltages up to 2,5 kV. It employs high-reliable, state-of-the-art technology for accurate measurements of ultra high insulation resistances up to 5.000.000 MΩ with four test voltages: 0,5 kV - 1 kV - 1,5 kV - 2,5 kV.
-
Product
Electronic Loads
T3EL Series
-
The T3EL series is a family of single channel, 200 & 300 Watt Electronic Loads that are ideal for R&D, product validation and Q&A in a bench or automated environment for low to medium power applications starting from 60mA, such as electronic components, batteries, portable chargers and power products. Electronic Loads are typically used to provide a load to the outputs of a power supply, usually capable of dynamic loading, and are fully programmable. Electronic Loads help designers to test electronic power products and ensure quality, reliability, and performance.
-
Product
Vibrators Electronics
VE464
-
The VE464 benefits from the latest developments in integration, radio transmission and servocontrol, allowing easier implementation of vibroseis seismic than ever before, even for advanced types of acquisition. Used in conjunction with the 428XL or 508XT acquisition system, the VE464 is a key component in achieving very high level of productivity.
-
Product
Light Sheet Microscopes
-
Discover advanced light sheet microscopy solutions from Leica Microsystems. Our portfolio combines cutting-edge technology with exceptional imaging capabilities to enhance your research.
-
Product
Electron Probe Microanalyzer
EPMA
-
JEOL commercialized the world's first FE-EPMA, the JXA-8500F in 2003. This highly regarded FE-EPMA has long been used in various fields, such as: metals, materials and geology in both industry and academia. The JXA-8530FPlus is a third-generation FE-EPMA that comes with enhanced analytical and imaging capabilities. The In-Lens Schottky field emission electron gun combined with new software provides higher throughput while maintaining high stability, thus allowing a wider range of EPMA applications to be achieved with higher resolution.
-
Product
Electron Beam Lithography System
-
Spot type Electron Beam Lithography System JBX-8100FS achieved high throughput, small footprint and electric power saving.
-
Product
Cathodoluminescence Solutions for Electron Microscopy
CLUE Series
-
HORIBA Scientific's Cathodoluminescence Universal Extension enhances any SEM’s analytical capabilities while maintaining its original functionality. Since the sample is able to remain in the same spot, CLUE can easily be combined with other microscopy applications, such as EDS and EBIC.
-
Product
Stereo Microscopes
-
Sometimes called dissecting microscopes, stereo microscopes provide comfortable 3-dimensional viewing of a sample in which each optical path (eye) sees the sample from a slightly different angle. Stereo microscopes are used to observe and manipulate samples in disciplines such as research, assembly and manufacturing, gemology and jewelry making, sample preparation and, of course, dissection. ACCU-SCOPE stereo microscopes can be found across a wide range of industries and institutions including biology labs, universities, research institutions, government facilities, biopharmaceuticals, manufacturing facilities, and more. Stereo microscopes are also available on a variety of stands and with a variety of illumination sources, offering features that may be particularly suited for your application.
-
Product
Semiconductor & Flat Panel Display Inspection Microscopes
MX63 / MX63L
-
The MX63 and MX63L microscope systems are optimized for high-quality inspections of wafers as large as 300 mm, flat panel displays, circuit boards, and other large samples. Their modular design enables you to choose the components you need to tailor the system to your application. These ergonomic and user-friendly microscopes help increase throughput while keeping inspectors comfortable while they do their work. Combined with OLYMPUS Stream image analysis software, your entire workflow, from observation to report creation, can be simplified.
-
Product
Electronic Ballast Tester
WT4000
-
• Measure parameter: 1) Input: Vrms, Lrms, W, PF, Hz, Phasic angle, total harmonic and 0-39 component of harmonic. 2) Output: Lamp voltage, Lamp current, Filament current, Guided cathodic current, Lamp power, crest factor and oscillatory frequency, single high frequency analysis. • Startup: Startup lamp voltage, lamp current, filament current, guided cathodic current curve and parameter, preheating time; • Simultaneously display on 8 windows for input and output parameters, convenient for comparison and analysis; • Test preheat energy, filament preheat time. And the parameters changes from 0 to 5s of filament voltage, filament current and filament power; • Up to 1MHz lrms test content to every EB; • Analysis symmetry of high Frequency curve of lout; • 12-bit high-speed A/D, sampling rate up to 10MHz, can easily analyse signal curve of output; • Finish an input and output testing at the same time within 1 minute; • Portable, can test, display, print without computer. Test report include data and curve, comply with international standard; • Communication port for PC, run under Windows98 or Windows2000, English Version available.
-
Product
Industrial Microscope Systems
-
Below you can see two industrial microscope systems which can be created using our components. Many other automated microscopy systems are possible using our components.
