Stimulus
-
product
Modular Power
RFP DC High Power
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
product
High Volume Manufacturing Handling, Stimulus
ULTRA P
The ULTRA P is a high performance production handler that provides thermal conditioning, full 6 DOF mechanical stimulus and an electrical ATE signal path for testing Micro-Electro-Mechanical Systems (MEMS) Accelerometers and Gyroscopes.
-
product
Accessories: Test Hardware
Copernicus Technology supply test hardware accessories to support Intermittent Fault Detection testing using VIFD™ and IFDIS™ test equipment, such as Interface Test Adapters (ITA). We also supply and repair general purpose and customer-spec test hardware accessories: ITAs, Break-Out Boxes (shown below) and Mobile Vibration Systems. The Mobile Vibration System can be quickly set up in repair bays for applying environmental stimulus to components and wiring harnesses during testing.
-
product
True-Mode Stimulus
S95460B
S95460B provides mismatch-corrected true-mode stimulus and enables accurate balanced measurements on M980xA PXI vector network analyzers.
-
product
Measurement and Analytics Solutions
Based on our OTP² system platform, we were able to implement a family of scalable test systems which is based on a common systems architecture, e. g. for products in the area of chemical analytics measurement. We not only implemented a universal, extremely comprehensive test system, but also a series of compact systems for benchtop placement which are fully compatible with the larger, universal system. Our specialized self-test adapters and test software enable fast verification of the test systems as well as partly automated calibration by the customer.Our systems are also used in electrical measurement applications, e. g. for calibrating analog input assemblies for PLC technology. For this purpose, specialized calibrators are integrated into the system; they provide traceable calibration of the relevant stimulus signals.
-
product
Overview of features and functionality
NoiseCheck Software
NoiseCheck is essentially SoundCheck without a stimulus editor, as it is designed for manufacturing the noise made by your product. It is a powerful piece of software, ideal for both R&D and production line acoustic measurements of fans, blowers, motors, gears, bearings, pumps and other electromechanical products.
-
product
PXIe Digital Stimulus/Response with PPMU: 250 MHz, 16 Channels
M9195B
The Keysight M9195B PXIe digital stimulus/response (PXI DSR) module is ideal for IC design validation and production test environments. The PXI DSR provides 16 bi-directional digital channels with programmable logic levels and can be configured for synchronized cyclized digital data, for parametric measurements, or for static digital IO.
-
product
COTS VME Board Tester
*Developed for support of Virginia Class Submarine at the COATS Integration Facility.*Provides Stimulus and Measurement Subsystem (SMS) to control, monitor, and evaluate VME assets used in the Non-Propulsion Electronic System (NPES) of the submarine.*Provides Native Environment Subsystem (NES) that simulates the operational configuration of typical NPES installations, and permits the test and evaluation of several types of VME assets.
-
product
Digital Wideband Transceiver Analysis
S94610B
Digital Wideband Transceiver Analysis is an add-on software to Device Measurement eXpert (DMX) that adds cross-domain stimulus response measurements for digital/RF mixed-signal device characterization. Included Waveform Creator helps define digital IQ test stimulus waveforms that are used in the RF signal generators for receiver tests or downloaded to the digital-to-analog converters for transmitter tests. The DUT control is customizable to accommodate various data converters and transceiver types by defining device operation settings, transmit/receive switching, reading and writing digital IQ waveform from and to DUTs. Acquired RF or digital data is processed in the VNA’s applications for faster, accurate measurements and analysis.
-
product
Nodal Impedance Analyser
QT-Hi1
Qmax Test Technologies Pvt. Ltd.
QT-Hi1 is an innovative Nodal Impedance Analyzer, which uses the industry’s proven V-I trace techniques of learn and compare of nodal impedances which are represented as VI Curves. It uses innovative Auto Best Curve fit technique an intelligent software alogorithm which enables automatic selection of the best fit value of Voltage, Source Impedance and Frequency of the stimulus waveform. The compact size with re-chargeable battery makes it an ideal companion for on-field applications. The wide 8” touch screen graphical display makes this tool more valuable in test and repair industry at all times.
-
product
Modulation Distortion For E5081A Up To 44 GHz
S960707B
The S960707B modulation distortion software application provides nonlinear DUT behavior tests (EVM, NPR, and ACPR) under modulated stimulus conditions.
-
product
USB Controlled Multi-Function DAQ For ATE Education And ATEasy Training
GT98901 Series
The GT98901 Demo board is a USB controlled, cost-effective, multi-function PCB assembly. The module is completely self-contained and includes an LCD display, measurement and stimulus resources, digital I/O, relays, and switches – all of which can be accessed and monitored via the USB port using a SCPI command set via a USBTMC interface which supports the USB488 protocol. Power for the board is provided via the USB interface, providing a totally self-contained assembly which can provide users with a simple yet complete vehicle that replicates many of the stimulus and measurement functions associated with ATE systems. When combined with Marvin Test Solutions' ATEasy® Test Executive and Test Development environment, the GT98901 is the ideal product for creating and supporting ATE training and education applications.
-
product
Protocol Analyzer and Exerciser
Keysight's protocol test solutions for each technology typically consists of both protocol analyzer application as well as a stimulus solution, such as an exerciser or traffic generator. Keysight's protocol test solutions combine multi-protocol analysis, traffic generation, performance and conformance verification to debug, validate and optimize your designs using high speed protocol standards.
-
product
VXI 12-Channel, 3-Wire LVDT/RVDT Simulation
65DL2
NAI’s 65DL2 is a 12-channel, 3-wire, LVDT/RVDT Simulation Instrument on a VXI board. This single-slot, message-based board features up to 12 stimulus channels of 3-wire LVDT/RVDT, wraparound self-test, and onboard programmable excitation supply. The board is uniquely versatile, as each excitation input and output voltage is programmable. In addition, each channel can be programmed to be controlled by an external DC voltage. A replacement for the 5410C-83, the 65DL2 is ideally suited for defense, commercial aerospace, and industrial applications.
-
product
16-Channel 250kSa/s USB Modular Multifunction Data Acquisition
U2351A
The U2351A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2351A to simulate simultaneous analog input acquisition.
-
product
Modular Power
RFP Controller
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
product
14-bit 16 Concurrent Channel 65MSPS A/D board
AD14-65Mx16AVE
14-bit 16-concurrent channel 65MSPS A/D board for demanding large-system uses, where signals on multiple time-aligned channels need to be observed with high SNR, such as RADAR, nuclear instrumentation, ultrasound, medical imaging, spectroscopy, communications systems, RF component and antenna testing and other critical applications. An on-board low-jitter LMX2581-based RF synthesizer allows any A/D sampling rate between 20MSPS and 65MSPS to be specified in software. A second on-board LMX2581 with synchronized reference can be optionally used to output four stimulus clocks on SMA connectors that can be vectored to any combination of 4 external transmitters, microwave pulse generators, laser modulators, and other devices.
-
product
Modulation Distortion Up To 50 GHz
S930705B
S930705B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 50 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930704B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
product
Serial Analyzers
This product enables passive monitoring, debugging, and target system analysis of all speeds of Serial RapidIO Gen2 and Gen1 from the physical coding-sublayer (PCS), through serial protocol, to full-duplex link protocol exchanges. Stimulus transmitters allow for injection of SRIO packets, control symbols, and 8b/10b characters.
-
product
6U CPCI D/S, S/D, I/O & Comm Board
78CS2
NAI’s 78CS2 is a 6U cPCI Multifunction I/O and Communication Board designed for applications requiring Digital-to-Synchro/Resolver (D/S) stimulus output, as well as I/O and communication functions. This board contains five independent function module slots. The board can be configured for 10 D/S channels, or for D/S in combination with I/O and communication modules. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
product
ULTRA Test Cells
The ULTRA Series of high performance MEMS handling, stimulus and test cells provides unparalled flexibility and capability for engineering development, characterization or high volume production test of inertial MEMS (accelerometer, gyroscope) semiconductor devices.
-
product
Synchro To Digital & Digital To Synchro Converter
DP-cPCI-5031
DP-cPCI-5031 is a Resolver to Digital and Digital to Resolver converter module. This module has four S/R to Digital converters(measurement channels) and two Digital to S/R converter(stimulus channels). This module is programmable for simultaneous acquisition and generation of the Resolver signal.
-
product
Detector Test Bench
RTB 3000
The RTB 3000 Detector Test Bench from Santa Barbara Infrared (SBIR) is a flexible integrated IR detector test station for evaluation of single element detectors, linear arrays, and focal plane arrays. The RTB 3000 provides the radiometric stimulus necessary to perform accurate IR detector testing in both laboratory and production environments.
-
product
Modular Power
RFP AC Power
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
product
LASAR Post Processor, Run Time And Diagnostic Test Solution
DtifEasy Series
DtifEasy is a full-featured tool set for importing, converting, and executing IEEE-1445 compliant digital test vectors generated by a LASAR simulation. All four IEEE-1445 file types - UUT model group, Stimulus and Response group, Fault Dictionary group, and Probe group are supported by DtifEasy; providing the user with the ability to execute go/no-go, fault dictionary, and guided probe sequences. DtifEasy supports MTS' 3U PXI GX529x series of dynamic digital instrumentation to 200 MHZ as well as the 6U PXI GX5960, 50 MHz digital instrumentation. All of these instrument families are compatible with the digital logic probe.
-
product
Frequency Response Analyser
DP-cPCI-7554
DP-cPCI-7554 is a cPCI module capable of analyzing the phase and gain characteristics of a system. The system under test is stimulated by the user defined waveform. The obtained response is correlated with the applied stimulus by the on-board DSP processor to determine the phase difference and the gain.Gain and the face analysis is carried out only at sine waveform.
-
product
Modulation Distortion Up To 70 GHz
S930707B
S930707B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 70 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930707B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
product
Sensors Test Cells
Integrated MEMS
The best technical performance, cost optimization, one-shot factory integration.A single unit integrates the modules for the handling, contacting and complete testing of MEMS devices, including the physical stimulus for functional test, and the tri-temp thermal conditioning.
-
product
VXI Video Processor System
65VP1
NAI’s 65VP1 is a Video Processor System (VPS) on a VXI board. Capable of highly accurate video stimulus and measurements, this state-of-the-art instrument is the culmination of over three generations of Automatic Test Equipment (ATE) development programs. It provides increased functional density, and it reduces power consumption, size, and cost of the overall system. The 65VP1 is ideally suited for defense and commercial ATE programs, including television applications.
-
product
Chroma LCR Meters
Chroma Systems Solutions, Inc.
Some of the key features to look for in an LCR meter (also known as an impedance meter) are: accuracy, test frequency, measured parameters, test voltage and test current. Additionally, an easy to understand display of test results and the ability to access and use these results has become increasingly important. Component testing often requires much more than simply a resistance, capacitance or inductance value at a given test frequency and stimulus voltage. An LCR meter or impedance meter must have the flexibility to provide multi-parameters over wide frequency and voltage ranges.





























