Stimulus
-
Product
PMC Bus Analyzer / Exerciser
PMC650
-
The PMC650 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation and fault generation- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics
-
Product
Stimulus Test Cell
HA7300
-
The Stimulus Test Cell HA7300 is a test cell which provides an environment for high-speed, highly accurate temperature and pressure test of differential pressure sensors, utilizing Advantest’s unique temperature control unit with simultaneous temperature control for 8 devices, as well as a newly developed 2Port pressure controller and pressure application nozzle.
-
Product
14-bit 16 Concurrent Channel 65MSPS A/D board
AD14-65Mx16AVE
-
14-bit 16-concurrent channel 65MSPS A/D board for demanding large-system uses, where signals on multiple time-aligned channels need to be observed with high SNR, such as RADAR, nuclear instrumentation, ultrasound, medical imaging, spectroscopy, communications systems, RF component and antenna testing and other critical applications. An on-board low-jitter LMX2581-based RF synthesizer allows any A/D sampling rate between 20MSPS and 65MSPS to be specified in software. A second on-board LMX2581 with synchronized reference can be optionally used to output four stimulus clocks on SMA connectors that can be vectored to any combination of 4 external transmitters, microwave pulse generators, laser modulators, and other devices.
-
Product
Accessories: Test Hardware
-
Copernicus Technology supply test hardware accessories to support Intermittent Fault Detection testing using VIFD™ and IFDIS™ test equipment, such as Interface Test Adapters (ITA). We also supply and repair general purpose and customer-spec test hardware accessories: ITAs, Break-Out Boxes (shown below) and Mobile Vibration Systems. The Mobile Vibration System can be quickly set up in repair bays for applying environmental stimulus to components and wiring harnesses during testing.
-
Product
Graphical Debugging for Verilog, VHDL, and C++ Simulators
BugHunter Pro
-
BugHunter uses the SynaptiCAD graphical environment and supports all major HDL simulators. It has the ability to launch the simulator, provide single step debugging, unit-level test bench generation, streaming of waveform data, project management, and a hierarchy tree. The unit-level test bench generation is unique in that it lets the user draw stimulus waveforms and then generates the stimulus model and wrapper code and launches the code. It is one of the fastest ways to test a model and make sure that everything is working correctly. The debugger also has exceptional support for VCD waveform files.
-
Product
Measurement and Analytics Solutions
-
Based on our OTP² system platform, we were able to implement a family of scalable test systems which is based on a common systems architecture, e. g. for products in the area of chemical analytics measurement. We not only implemented a universal, extremely comprehensive test system, but also a series of compact systems for benchtop placement which are fully compatible with the larger, universal system. Our specialized self-test adapters and test software enable fast verification of the test systems as well as partly automated calibration by the customer.Our systems are also used in electrical measurement applications, e. g. for calibrating analog input assemblies for PLC technology. For this purpose, specialized calibrators are integrated into the system; they provide traceable calibration of the relevant stimulus signals.
-
Product
16-Channel 500kSa/s USB Modular Multifunction Data Acquisition
U2353A
Data Acquisition Module
The U2353A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2353A to simulate simultaneous analog input acquisition.
-
Product
64-Channel 1MSa/s USB Modular Multifunction Data Acquisition
U2331A
Data Acquisition Module
The U2331A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2331A to simulate simultaneous analog input acquisition.
-
Product
Overview of features and functionality
NoiseCheck Software
-
NoiseCheck is essentially SoundCheck without a stimulus editor, as it is designed for manufacturing the noise made by your product. It is a powerful piece of software, ideal for both R&D and production line acoustic measurements of fans, blowers, motors, gears, bearings, pumps and other electromechanical products.
-
Product
RF-Ready DC Fixture
-
The RF-Ready DC fixture provides space for mounting RF input and output matching circuits. Hence, it is possible to tune up the assembly at a remote test station, such as a network analyzer, to peak performance and then run the life test with DC stimulus. The matching structures also allow incorporation of more complex stabilization structures.
-
Product
High Speed Digital Analog
ITA
The Automatic Test Equipment is designed to provide R&D and the Production floor with a high quality, reliable and easy to use Test Station comprised of COTS equipment from industry leading instrument manufactures. The measurement switching has low thermal offset allowing for micro volt measurements. The switching also accommodates both stimulus and measurement up to 5 Amps. Also to provide High Speed and Static Digital Stimulus and Response that covers LVDS, 3.3V, TTL, CMOS and Industrial logic families. For Serial communications there are SPI, I2C, RS232/485, USB and Ethernet. The system has nine programmable DC power supplies that are capable of powering both the UUT and the UUT interface separately. The system can interface with a variety of UUT’s via an ITA. Each system comes with the Imperial Test Executive, National Instruments TestStand, CVI, LabView and .NET Runtime.
-
Product
Modular Power
RFP DC Load
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
Product
64-Channel 500kSa/s USB Modular Multifunction Data Acquisition
U2356A
Data Acquisition Module
The U2356A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2356A to simulate simultaneous analog input acquisition.
-
Product
Modular Power
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, programmable power module system providing DC, AC and electronic load assets all under control of a single controller. ReFlex Power™ (RFP™) provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test.
-
Product
Frequency Response Analyser
DP-cPCI-7554
-
DP-cPCI-7554 is a cPCI module capable of analyzing the phase and gain characteristics of a system. The system under test is stimulated by the user defined waveform. The obtained response is correlated with the applied stimulus by the on-board DSP processor to determine the phase difference and the gain.Gain and the face analysis is carried out only at sine waveform.
-
Product
Modulation Distortion Up To 13.5 GHz
S930701B
-
S930701B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 13.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930701B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Synchro To Digital & Digital To Synchro Converter
DP-cPCI-5031
-
DP-cPCI-5031 is a Resolver to Digital and Digital to Resolver converter module. This module has four S/R to Digital converters(measurement channels) and two Digital to S/R converter(stimulus channels). This module is programmable for simultaneous acquisition and generation of the Resolver signal.
-
Product
Modular Power
RFP DC High Power
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
Product
Modulation Distortion Up To 26.5 GHz
S930702B
-
S930702B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 26.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930702B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Fault Diagnostics in Power-Off State
QT55
-
Qmax Test Technologies Pvt. Ltd.
Signature Method of Testing is also known as VI Trace Characteristics, is a proven fault diagnostics technique in Power-Off state while testing a board. By applying known wave from signal with desired Voltage, Source impedance and Frequency of the stimulus signals, depending upon the test node and its characteristics, a Voltage (V) vs Current (I) graph is plotted and studied.
-
Product
Frequency Response Analyzers
-
Frequency Response Analysis (also referred to as Transfer Function Analysis) measures the output spectrum of a system relative to a stimulus, and is used to characterize the dynamics of the system under test. The technique measures the magnitude and phase relationship between output and input waveforms as a function of frequency. The input signals may be from a wide range of sensors including acoustic (microphones/sonar), mechanical (accelerometers/displacement transducers), optical (photodetectors), and electrical (amplifiers).
-
Product
Modulation Distortion Up To 90 GHz
S930709B
-
S930709B enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 90 GHz. The wide dynamic range and vector error correction of the PNA-X results in an extremely low residual EVM of the test setup, delivering you a complete picture of your device’s performance without test system interference. S930709B measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Accessories: Mobile Vibration System
-
The Mobile Vibration System from Copernicus Technology is a new and affordable system for applying vibration stimulus during testing work, with a range of features that make it highly adaptable and fully configurable by the user.
-
Product
MEMS Inertial Test
-
Cohu´s inertial solutions enable high precise Gyroscope and Accelerometer test with best-in-class cost of test due to high parallelism and package flexibility. All Cohu stimulus modules guarantee high precision and velocity stability as well as high temperature accuracy. With use of our high efficient handler portfolio we can offer the ideal solution with optimized cost of test.
-
Product
RF Sources
-
Textron Systems’ commercial RF Sources (RFS 340, SSI) provide an unmatched combination of frequency coverage, power range, signal fidelity and switching speed in either a two-slot VXI, 1U LXI®, or VME Synthetic Stimulus Instruments (SSI) format.
-
Product
DC Automated Accelerated Reliability Test Station (AARTS)
DC-HTOL
-
The DC Automated Accelerated Reliability Test Station (AARTS) systems are designed to maximize channel density. The first systems developed by Accel-RF (ARF) were intended for RF and DC stimulus to the Device Under Test (DUT). However, there are some applications in which RF stimulus is not required.
-
Product
CompactPCI & CompactPCI-X Bus Analyzer / Exerciser
CPCI850
-
The CPCI850 analyzer provides a multitude of functions to help analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
64-Channel 250kSa/s USB Modular Multifunction Data Acquisition
U2355A
Data Acquisition Module
The U2355A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2351A to simulate simultaneous analog input acquisition.
-
Product
Modular Power
RFP AC Power
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
Product
PMC and PMC-X Bus Analyzer / Exerciser
PMC850
-
The PMC850 analyzer provides a multitude of functions to help analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
