Calibration
maintains accuracy of test asset by correcting out of specification conditions.
See Also: Calibrators, Power Calibration, Display Calibration, Calibration Standards, Calibration Software, Calibration Services, Calibration References
-
Product
Temperature Calibrators
-
Fluke Temperature Calibrators simulate process sensors for testing temperature instrumentation. Specifically designed for the field, these lightweight compact tools are EMI tolerant, dust and splash resistant and offer an easy to use single push button interface. When paired with a temperature sensor they can take high accuracy temperature measurements to verify process temperatures and ensure the highest product quality and safety. There are a variety of different temperature calibrators designed for your unique calibration and testing requirements.
-
Product
Bench Digital Multimeter, Calibrated, 1 kV, 10 A, 3.8 Digit
72-1015 CAL
-
The 72-1015 CAL from Tenma is a digital bench type true RMS multimeter. It has auto and manual range options with maximum reading of 5999 counts and 3-5/6 digits which has a unique outlook design. In addition to all the conventional features including DC/AC voltage, current, resistance, diode, continuity test, diode test capacitance, temperature, transistor, max/min, there is a data hold, low battery display, sleep mode, RS232C serial port for easy connection with computer to realize macro recording, monitoring and capture of transient dynamic data, displaying change of waveform during the measurement, providing data and evidence to engineering technicians for scientific research. This meter complies with the standards IEC61010, pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) double insulation and CE marked.
-
Product
Handheld Water Quality Meters
LAQUA PC210
-
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers)- 0.01 pH resolution- Offset and average slope display- ORP calibration option- Automatic / manual temperature compensation and temperature calibration function- Automatic (up to 4 points) and manual (up to 5 points) conductivity calibration- Adjustable reference temperature and temperature coefficient- Adjustable cell constant and selectable measurement unit- Conductivity and total dissolved solids (TDS) conversion- Four (4) TDS calibration curves for wide range of applications: EN27888, Linear, 442, NaCl- Two (2) salinity calibration curves: NaCl, Seawater - Auto log data; built-in memory can store up to 500 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached - Monochrome LCD with white LED backlight: 50 x 50 mm- Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrodes and calibration solutions in carrying case- 3 years meter warranty
-
Product
Premier Industrial Shakers
-
The Hardy Shaker ensures that the Seismic Sensors and Transmitters that you have installed are working properly and giving you the results you need. Just like the pressure and flow instruments in your facility need calibration checks every year, so do your Seismic Sensors and Transmitters. This system puts the calibration check of those Seismic Sensors and Transmitters within your control, and within your budget.
-
Product
Coaxial Fixed Attenuator, DC to 12.4 GHz
8491A
Attenuator
The Keysight 8491A coaxial fixed attenuator provides precision attenuation, flat frequency response and low SWR over broad frequency ranges. The attenuator has type-N connectors and is available in nominal attenuations of 3 dB and 6 dB, as well as 10 dB increments from 10 dB to 60 dB. This attenuator is swept-frequency tested to ensure specification compliance at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
Product
Temperature Controlled Air Bath
9300A
-
Measurements International Ltd.
The model 9300A series of Temperature Controlled Chambers is designed as a convenient and inexpensive way to maintain the temperature of air resistors in the calibration laboratory. It is large enough to house several standard air resistors and features two adjustable shelves to permit easy access to the standards. The shelves are easily removable.
-
Product
Radiated Emission
-
High accuracy CISPR 16-1-1 EMI receivers and high precision calibrated antennas for radiated emission measurements.
-
Product
Turning Mirror
10769A
-
The 10769A is ideal for use in laser measurement and calibration applications. In the calibration of slant bed lathes, for example, the beam steering mirror deflects the beam from the laser head upward, through the interferometer, along the lathe's cross slide. One or more mirrors can also create a path from a laser head to an interferometer located in an otherwise inaccessible position, as in the case of a milling machine with a table that moves in only one axis.
-
Product
Three Phase Meter Test Bench
-
Supreme Instrument Laboratories
Three phase meter test bench suitable for calibration & testing of AC Ammeters, Voltmeters, Single phase Energy Meters, Watt Meters, Power Factor Meters, Three Phase Two Wire & Three Phase Four Wire Energy Meters Trivector Meters, Maximum demand indicators, of active & reactive systems, Three phase 3 wire & 4 wire watt meters, Var Meters, Power Factor Meters etc.
-
Product
MAX Waterproof 3-in-1 pH/ORP/Temp Tester
pH58
-
The Milwaukee pH58 MAX Waterproof 3-in-1 pH/ORP/Temp. Tester is one of our most accurate cost effective, well rounded, rugged and reliable testers in the market featuring dual level LCD readouts, easily replaceable probe and extended pH ranges to meet almost any application. It's simple 1 or 2 point automatic calibration is simple-to-use and offers TWO sets of memorized buffers to select. Ideal for use in beer, food, wine, education, water treatment, pools and many other applications.
-
Product
Cryostat Calibrators
-
Electronic Development Labs, Inc.
Specialized, low-temperature, passively cooled, or liquid nitrogen-based apparatuses designed to calibrate temperature sensors (RTDs, thermocouples, PRTs) at cryogenic levels.
-
Product
Adapter
ZET 430
-
*Aligns sensor output signal with the FFT spectrum analyzer input;*Sends the FFT spectrum analyzer generator signal to the sensor calibration input;*Provides power supply to the sensor from the integrated ±12 V power supply unit.
-
Product
Fingernail Test Probe
CX-Z11
-
Shenzhen Chuangxin Instruments Co., Ltd.
The Fingernail Test Probe is used to test to IEC 60335 and UL standards. It checks the security of parts that snap together. The spring loading in the handle can be calibrated to the force necessary to use the instrument. This probe is made of stainless steel with specially hardened tip and a Delrin?handle. Handle has a threaded hole for use with force gauges.
-
Product
10KV High Voltage Digital Insulation Resistance Tester
KM 6213AIN
-
Kusam Electrical Industries Limited
• The KM 6213A IN is the KUSAM-MECO premium model of High Voltage Digital Insulation Resistance Testers.• The KM 6213A IN has new added features with a low consumption High Performance processor.• It displays results much faster and has more advanced features.• The KM 6213A IN has Automatic Polarization Index and Dielectric Absorption Ratio Calculations.• Results are displayed on the new High Contrast LCD. It’s mounting angle makes it more readable for all users, in different working conditions.• The user’s manual reflects the new features and added benefits of this instrument.• It has Auto-Off, Auto-Stop, EnerSave™ and is a non destructive tester.• Once you start the tester, it waits for your selection. You can go up and down in voltage to select the voltage at which you want to test the insulation. Once you have selected that voltage, you need to connect the test leads to the Insulation Tester to measure. Then it measures voltage to ensure there is no voltage present on the equipment under test. If there is a voltage present, it will warn you to disconnect the circuit before proceeding. If it’s free of any voltage, then you can proceed with the testing. This ensures that no damage is done to the Insulation Tester KM 6213AIN.• One of the new innovation on this tester is also the way the new unique calibration process works. It’s fully digital, has no moving parts and does not require expensive and complicated jigs or computers systems to be calibrated. It’s cheaper to maintain than any other Digital HV Insulation tester on the market today. The KM 6213AIN is supplied standard with our Premium test Leads Kit, the AL-50.
-
Product
NI-9263, 100 kS/s/ch Simultaneous, ±10 V, 4-Channel C Series Voltage Output Module
783740-01
Voltage Output Module
100 kS/s/ch Simultaneous, ±10 V, 4-Channel C Series Voltage Output Module - The NI‑9263 is a simultaneously updating analog output module. It features overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST‑traceable calibration. The NI‑9263 module includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
Product
Temperature Calibrators
-
AMETEK Sensors, Test & Calibration
Our dry-block and liquid bath temperature calibrators include 6 series with more than 25 models and temperature ranges from -100 to 1205°C. All feature portability, accuracy, speed, and advanced documenting functions with JofraCal calibration software. Our calibrators include the smallest and coldest dry-block calibrators available.
-
Product
Calibrating Equipment
-
Stability DC : < 0.01 %FS / 3 min, AC : < 0.02 %FS / 3 minRipple : < 0.2 %Power Supply : 230 VAC, 50 (60) HzPower Consumption : < 250 VAOperating Temperature : 5ºC to 35ºCRelative Humidity : ≤ 80 %Distortion : < 0.5 %Display : 51/2 Digit LED Digital DisplayStep adjustment of Output Signal : 100 %FS / N, 10 %FS / N,%FS / N, 0.1 %FS / N (N = 4, 5, 6, 10 and 15)Dimensions : 190mm (H) x 480mm (W) x 545mm (D)Total Weight : 22.5 kgs (approx.)
-
Product
Pin Brinell Tester
-
Newage Testing Instruments, Inc.
The Pin Brinell is a cost effective instrument, which uses a calibrated shear pin to control the amount of load applied. Provides consistent loading regardless of operator. Tests in 100 - 730 equivalent Brinell range.
-
Product
CW Power Sensors
E-Series
-
The E-Series of power sensors have their calibration factors stored in EEPROM and operate over a wide frequency and dynamic range.wide frequency coverage from 10 MHz to 26.5 GHz (sensor dependent)wide dynamic range sensors (-70 to +20 dBm)accurate CW average power measurementsoperates with the EPM, EPM-P, and P-series power meterscalibration factors stored in EEPROM
-
Product
C-DF Res Calibrator
-
This calibration box is used to routinely check and inspect test sets. The portable calibrator offers one Capacitance, three Tan Delta and four Resistivity values. The maximum operating voltage is 500V AC/DC.
-
Product
Stand-Alone Doppler Current Sensor
DCPS
-
The Doppler Current Profiler Sensor (DCPS) is a medium-range, 600kHz current profiler smart sensor. It offers high-quality ocean current measurements and is ideally suited for cabling directly to various systems or dataloggers via serial or AiCap bus. With its integrated compensation for tilting and movement, the sensor is commonly used to measure current from buoys and other moving platforms.The 5400/5400R version of the current sensor is 300m depth rated, the 5402/5402R version is 4500m depth rated, and the 5403/5403R version is 6000m depth rated and intended for commercial as well as research use. It comes with an integrated temperature sensor that can be calibrated on request.As an extension to the DCPS, we now offer the current profiler with an integrated pressure unit called the 5400P. This version enables acoustic wave measurements in addition to profiling currents. Ideal for small observatories, the DCPS sensor is the market's lowest-cost current and wave sensor.
-
Product
nVision Reference Recorder
-
AMETEK Sensors, Test & Calibration
Accurate enough to replace a deadweight testerRugged enough to sit in 3 feet of waterPortable enough to complete calibrations anywhere
-
Product
Custom Test & Measurement
-
Delserro Engineering Solutions
DES provides customized bench test and measurement services. After conducting the test, we have the tools and experience to analyze the data and offer solutions to your problems. All of our instruments are maintained and calibrated traceable to NIST standards.
-
Product
Light / Lux Meter, Calibrated w/D & U, 50000 lx, 100 lx, 4 %, 185 mm, 78 mm, 38 mm
72-7250 CAL DU
-
The 72-7250 CAL DU from Tenma is a digital light meter with RS232 capability. It has custom one-chip microprocessor LSI circuit which ensures high accuracy. The meter features 13mm (0.5”) super large LCD display with contrast adjustment for best viewing angle, data hold and auto power off. It records maximum, minimum and average readings with RECALL facility. The 72-7250 has RS-232 PC serial interface, user selectable lighting type (tungsten, fluorescent, sodium or mercury, daylight) and zero adjustment by push button. The meter operates from 9V battery.
-
Product
Bond Force Measurement And Calibration Systems
BFS-20
-
Based on its design and easy handling it can be used also on other brands to measure the bond force.
-
Product
Optical Receiver Stress Testers
-
Developing next-generation optical receiver technology requires world-class stress testing. Use Keysight's automated calibration solution and get optical stressed eye results in one-tenth the time compared to a manual setup.
-
Product
Automatic Antenna Tuner 3.5 kW
DU 3500 AL
-
The DU 3500 AL automatic tuner has been primarily manufactured for an automatic PA, but it can also be used with any manual PAs as well. The tuner is primarily compatible with the OM POWER automatic PA.This tuner was designed for antennas calibrated to HAM BANDs. The maximum power can only be utilized with these antennas. With other antennas, it should be set at a lower power (max. 2kW).The major advantage of the tuner is that during competitions it is possible to change BANDs particularly quickly.
-
Product
Hipot Line Testers
-
The newest product of our Hipot Line Testers, the UL Listed HT-S series hipot now comes with an adjustable ground continuity test in range of 0.08 - 1.50 , and Auto-offset for test leads up to 1.00 . Performs 0-2000 AC Hipot Test. Neutral/Hot to Ground Leakage current test up to 20 mA AC. Easy to use and connect. Ships complete with cables, manual, and a Calibration Certificate.
-
Product
Non-Contact Displacement Sensing System
KD-2306
-
Multi-purpose non-contact position/displacement sensing* Supports both dual and single coil sensors* Terminal I/O connections* Auto-synchronization of multiple channels* Analog DC and 4-20mA outputs* Single ended, bipolar, and differential voltage outputs* Front face coarse and fine calibration controls* RoHS compliant and CE marked
-
Product
Antenna, Dual Ridge Horn
EM-6963 | 18 GHz – 40 GHz
-
Model EM-6963 can be individually calibrated for use in EMI/EMC compliance measurements as well as for general purpose measurement antennas over its specified frequency range.
