Distribution
transmission's network array.
-
Product
Amplifiers, Splitters & Combiners
-
DEV’s RF Splitters, Distribution Amplifiers, or Dividers are used to distribute and amplify RF signals, to compensate for signal loss, and to provide redundancy paths to ensure maximum uptime.
-
Product
Wet-Mateable Connector, 10k V, 250 A
Nautilus WM10-250
-
Trends in subsea oil & gas production are moving towards deeper water and longer step out distances. These trends drive demand for higher power equipment and higher power delivery and distribution capabilities subsea with high pressures and temperatures. Teledyne ODI'™s Nautilus WM10-250 is designed with the benefit of advanced material science testing and certification, and with insulation and redundant sealing systems for reliable performance in long-term harsh environments.
-
Product
High Voltage Divider
-
HIGHVOLT Prüftechnik Dresden GmbH
Is a passive linear circuit that produces an output voltage (Vout) that is a fraction of its input voltage (Vin). Voltage division is the result of distributing the input voltage among the components of the divider. A simple example of a voltage divider is two resistors connected in series, with the input voltage applied across the resistor pair and the output voltage emerging from the connection between them.
-
Product
Quality Control for more Precision in Press Hardening
PRESS-CHECK
-
The automated test system PRESS-CHECK works with two powerful high-end thermographic cameras for continuous measurement of two-dimensional temperature distribution. This measurement is carried out before the pressing operation on the surfaces of the boards to be processed and subsequently on the resulting molded parts, ultimately enabling exact compliance with the thermal process parameters.
-
Product
WinstonCones
-
Our Winston Cone condenser is a field optic designed for maximum concentration of far infrared and sub millimeter radiation. Its principal functions are to:*Concentrate the radiation onto a detector smaller than the field aperture*Restrict the field of view of the detector*Distribute the incoming energy uniformly across the detector
-
Product
6-Ch 200 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - 6U VPX
Model 58621
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Six 200 MHz 16-bit A/Ds- Six multiband DDCs (digital downconverters)- Two DUCs (digital upconverters)- Four 800 MHz 16-bit D/As- Two multiboard programmable beamformers- 4 GB of DDR3 SDRAM; 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
4U 8 Slot VME64X Mini Crate
VME8008X
-
The Model VME8008X is a 8 slot VME crate, suitable for 6U x 160mm boards, with VME64X compliant backplane. The Unit is powered by 100 – 240 Vac (50 – 60 Hz). The power distribution is 25A@+5V, 10A@+12V, 10A@-12V, 25A @ +3.3V. The VME8008X provides Automatic daisy chain and supports Chained Block Transfer (CBLT).
-
Product
cRIO-9048, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 8-Slot CompactRIO Controller
785619-01
-
1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 8-Slot CompactRIO Controller - The cRIO-9048 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 160T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
Video Signal Distributor
MSHM-405S
-
MHSM-405S, HDMI Distributor, distribute four (4) digital video sources to the five (5) output channels. The built-in amplification function enables HDMI signal distribution without signal loss. The product guarantee to support full channels HDMI/HDCP compliance which means NEVER displaying HDCP certified sources in not-HDCP certified Tvs. User can select one (1) input source of the four (4) and make sure connected condition for HDCP & EDID test with led color of the front panel.
-
Product
Digital Arrester Clamp Tester
ALCL-40L
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Lightning arresters are designed to protect a power distribution system by shunting to ground the high voltage surges caused by lightning. ALCL-40L measures to warn that an arrester is damaged or deteriorated and should not be energized.
-
Product
DC/DC Power Supply
PCM-DC-AT512-P
-
WINSYSTEMS’ PCM-DC-AT512-P is a triple output, DC/DC power supply that can mount anywhere in a PC104 stack. It features a very wide voltage input range from 10 to 50 volts DC. This allows the unit to operate with 12, 24, or 48 volt battery or distributed DC power systems. It opens up a wide array of applications including transportation, Mil/ COTS, security, solar-powered, and telecommunications.
-
Product
4-Channel 200 MHz A/D with DDC, VITA 49.0, Virtex-6 FPGA - 6U VPX
Model 57664
-
- Supports Xilinx Virtex-6 LXT and SXT FPGAs- PCIe output supports VITA 49.0 VITA Radio Transport (VRT) Standard- Four 200 MHz 16-bit A/Ds- Four multiband DDCs (digital downconverters)- One multiboard programmable beamformers- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
AIOT Software, Distribution & Services
-
Advantech Embedded Software provides a wide variety of IoT solutions you need from IoT devices operation management software to cloud platform services that help customers build, manage, and deploy applications on a global network with preferred IoT frameworks as well as IoT security services, including backup recovery, embedded BIOS, OS, API Library and integrated service platforms on WISE-PaaS Marketplace.
-
Product
Transformer Testing
-
The ART-3D series of Automatic Ratio Testers are precision instruments, designed to measure the turn ratios, phase displacements, excitation currents of single phase and three phase power, distribution and instrument transformers in conformity to the IEEE C57.12.90 & IEC 60076. Now featuring an enhanced test lead design, the ART-3D is the perfect instrument for real-life field usage. ART-3D series also has Anti Induction circuit which makes it suitable for system voltages upto 765KV.
-
Product
FPGA Mezzanine Cards
-
FMCs bring modularity to high performance I/O - whether you need high bandwidth ADCs and DACs for radar applications, Gigabit Ethernet for digital communications, or clock and trigger distribution for multi-board synchronization.
-
Product
NI-9202, ±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module
784400-01
-
±10 V, 10 kS/s, 24-Bit, 16-Channel C Series Voltage Input Module - The NI-9202 has excellent flexibility to meet the needs of your applications. The module has 16 simultaneous sampling, differential input channels to create large, distributed systems in a rugged form factor. It also has configurable filters to eliminate noise in your system while maintaining low-latency to be used in control systems.
-
Product
DAS Antennas
-
In-Building Distributed Antenna System (DAS or i-DAS) antennas are low profile and designed to be mounted discreetly to a hard or tiled ceiling. Used in a series throughout large buildings, campus areas or even in below ground sections of a building the antennas can provide a distributed LTE or Wi-Fi signal to where it is required most. With a growing demand for in-building connectivity and higher data rates, larger smart or connected buildings require a series of antennas in order to distribute signal around the building or campus area.
-
Product
Logger version optical fast DO sensor
RINKO I / I D
-
Rinko I is an autonomously deployable data logger with a fast response optical DO sensor. The instrument and the software with various operating mode offer flexible observations in the field. The small-sized and the self-contained unit with batteries and a data logger can be easily integrated on platforms (e.g. CTDs). Rinko ID has a depth sensor, allowing for DO vertical distribution measurements.
-
Product
NI-9145, 8-Slot, Zynq-7020 FPGA, EtherCAT CompactRIO Chassis
784756-01
-
8-Slot, Zynq-7020 FPGA, EtherCAT CompactRIO Chassis - The NI‑9145 is a rugged EtherCAT slave chassis for adding deterministic, distributed I/O to any CompactRIO, PXI, or industrial controller with two Ethernet ports. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. You can daisy chain multiple NI‑9145 slave chassis from the master controller to expand time-critical applications to higher channel counts while maintaining hard determinism with minimal processor resources.
-
Product
HAAS-3000/2000 High Accuracy Array Spectroradiometer (Laboratory Grade)
HAAS-3000
-
Hangzhou Everfine Photo-E-Info Co., LTD
HAAS-3000/2000 High Accuracy Array Spectroradiometer delivers various photometric, colorimetric and radiometric parameters as required by CIE standards.Measurement parameters are luminous flux (with integrating sphere), relative spectral power distribution, chromaticity coordinate, CCT(correlated colour temperature), CRI (color rendering index), SDCM (standard deviation of color matching), color purity, peak wavelength, dominant wavelength, etc.
-
Product
Circuit Break Timer Test Set
PME-500-TR
-
Before developing the system or equipment for the testing of a circuit break timer for distribution, the application information was obtained by consulting various users of this type of timer for circuit breaker. The customers consulted were from private service and maintenance companies, large industries, and of course from the Utility companies. It is essential to receive first hand information of the actual requirements and needs of each of these customers who are making these types of tests and then make a detailed study of the various alternatives offered by different manufactures of this type of circuit breaker timer.
-
Product
Clock And Timing
-
Achieving highly accurate precision timing is no easy feat from a technology perspective, so it’s important to find a resource you can trust to reduce design risk and speed your time to market. Our end-to-end timing solutions generate, distribute and apply precise time for multiple industries, including communications, aerospace and defense, IT infrastructure, financial services, power utilities and more. We provide a broad range of clock and timing solutions ranging from MEMS oscillators to active hydrogen masers. Explore our portfolio of clock and timing components and systems to find the right solution for your project.
-
Product
Thermal Imaging Camera
-
Zhejiang ULIRvisionTechnology Co., LTD
A thermal imaging camera is a device that uses infrared and thermal imaging technology to convert the image of the temperature distribution of the target object into a visible image through detecting the infrared radiation of the target object and applying signal processing and photoelectric conversion. The thermal imaging camera accurately quantifies the actual detected heat and images of the entire object in real-time in the form of a surface, thus accurately identifying the suspected fault area that is heating. The operator initially judges the fever condition and the fault location through the image color and hotspot tracking display function displayed on the screen of the thermal imaging detector, and strictly analyzes it, thereby embodying high efficiency and high accuracy in confirming the problem.
-
Product
IC-3121, 1.91 GHz Intel Atom Quad-Core Processor, 2-USB3 Port Industrial Controller
784961-01
-
1.91 GHz Intel Atom Quad-Core Processor, 2-USB3 Port Industrial Controller - The IC‑3121 is a compact and rugged industrial controller that withstands the harsh environments common in automation, supervisory control, distributed control, and industrial embedded OEM applications. The IC‑3121 offers two USB3 ports with dedicated bandwidth, FPGA-based I/O capabilities, and network connectivity for distributed control applications. The advanced features include the ability to synchronize image inspection results with industrial I/O and configure hardware-timed network triggers to trigger camera acquisition, motion control, or data acquisition. You can use the advanced FPGA personality that is shipped with the system or customize the FPGA functionality using the LabVIEW FPGA Module.
-
Product
Packaging Compression Tester
-
It is very important to evaluate compressive resistance of packaging material before its selection for maintaining product shape, quality while its transportation, distribution and handling in bulk.
-
Product
cDAQ-9181, 1‑Slot, Ethernet CompactDAQ Chassis
781496-01
-
1‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9181 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
Laser Diffraction Particle Size Analyzer
SALD-2300
-
The new standard in the SALD series. While maintaining continuity and compatibility with respect to the data of the SALD2000/2100/2200, which were popular, widely distributed models, this instrument is equipped with many new functions useful for evaluating changes (dispersion, aggregation, dissolution) in particle size distribution relative to the concentration or time. It supports a particle concentration range from 0.1 ppm to 20% and can perform a series of measurements of 200 data points at 1 second minimum intervals.
-
Product
Online Water Quality Monitor
TW-150
-
HORIBA's TW-150 is a process water quality measurement system designed for drinking water and water distribution plants. TW-150 monitors turbidity,color, free residual chlorine, water pressure and pH without any reagent for measurement.This chemical free method reduces operating costs as it requires minimal maintenance and improves process control.
-
Product
CATV RF Optical Receiver
L-RF-MN-RX
-
The QuestTel''s L-RF-MN-RX module optical receivers are versatile, low-cost and compact optical receivers for use in HFC fiber applications. It is perfect solution for the transport and distribution of CATV RF signals over fiber optic cable. The L-RF-MN-RX module housed in a small housing and have adjustable RF output level. May be used as a hand held device for testing, or placed at a customers premise for the reception of cable television services. The Receiver is designed to operate with a very low optical input level between the range of +3dBm to -12dBm.
-
Product
Video Management System Ancillary Products
-
Curtiss-Wright Defense Solutions
To complement our range of displays, video recorders and video distribution units, Curtiss-Wright Defense Solutions offers ancillary products that can bring additional capabilities to a video management system.
