Distribution
transmission's network array.
-
Product
Rack-Mounted Timing Systems
CommSync II Family
-
The CommSync II family of modular systems provide GPS time and frequency outputs to meet your synchronization requirements. All systems include support for multiple input and output modules including 1PPS, IRIG, HAVE QUICK, PTTI, IEEE-1588 PTPv2, low phase noise 1, 5, and 10 MHz sine wave as well as custom outputs.These systems are available with military SAASM MPE-S GB-GRAM, SAASM Force 22E MRU or civilian C/A GPS receivers. Rubidium or OCXO oscillators provide for excellent holdover performance in the event of failure of the reference inputs. In addition, they may be configured as Distribution Time and Frequency (DTF) systems that are synchronized by an external reference. Dual Redundant systems (CommSync II & CommSync II-D) may be configured with two GPS Time & Frequency (GTF) modules and two power supply modules (AC and/or DC power) for redundancy with uninterrupted automatic switchover.
-
Product
L-Band RF Tuner and 2-Channel 400 MHz A/D with Kintex UltraScale FPGA - XMC
Model 71891
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Two FPGA-based multiband DDCs (digital downconverters)- Xilinx® Kintex® UltraScale™ FPGA- Five GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Navigator BSP® for software development- Navigator FDK® for custom IP development- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Distribution Control
-
Schweitzer Engineering Laboratories, Inc.
SEL solutions improve distribution system reliability and efficiency with intelligent protection, monitoring, and control devices.
-
Product
MIMIC® IOS Simulator
-
MIMIC IOS Simulator is a command line simulator that fully supports Cisco IOS® software as well as NX-OS, JUNOS, NETCONF, other command line interfaces and SNMPv1, v2, v2c, v3. You can simulate up to 100,000 devices in a single workstation, and an unlimited number of devices can be simulated by distributing it over multiple workstations. You can access devices using Telnet, SSH and SNMP. Changes made using one protocol is reflected in the other.
-
Product
Multi-Sensor PBL
MS 1000-PBL-20
-
Advanced Thermal Solutions, Inc.
The MS 1000-PBL-20 is a three-sensor probe designed for the measurement of air velocity and temperature in the same vertical plane. It eliminates the need for multiple probes or a traversing probe for determining the flow profile or distribution.
-
Product
HPx-346 Analogue to Network Radar Converter
-
The HPx-346 is a small form factor, combined analogue radar input and network radar video distribution unit. The unit connects to the analogue video interface on a radar, digitises the data and distributes it as UDP packets over Ethernet.
-
Product
GONIOPHOTOMETRY
-
Goniophotometers are required to measure angular resolved distributions of photometric or colorimetric quantities, either by rotating the lighting device under test or by moving the sensor around the device. Depending on the application, different geometries are used to obtain distributions in the appropriate CIE coordinate system.
-
Product
Mass Spectrometry Imaging
-
Bringing together the powerful technologies of MALDI and DESI to discover, identify and measure a broad range of molecular targets in a single system solution with dedicated acquisition, processing, and visualization software. *More comprehensive, detailed information than from any individual imaging technique *Maximum information from minimal sample *Definitively and objectively interpret molecular distribution information*Intuitive, integrated software suite covering the full MS imaging workflow *Flexibility to adapt to changing day-to-day priorities and future needs *Single vendor for total system support
-
Product
Robust DIN-rail Fanless Embedded System With Intel® Atom® Processor E3827 (1.75 GHz)/E3845 (1.91 GHz), 6 COM, SATA SSD, DIO, 2 GbE LAN And RTC
rBOX510-6COM
-
The rBOX510-6COM, din-rail fanless embedded PC supports the Intel® Atom™ dual-core processor E3827 with 1.75GHz and onboard 4GB DDR3L system memory. The superior rBOX510-6COM features full rugged industrial designs: dual isolated Gigabit LANs, four isolated RS-232/422/485 ports, two RS-232/422/485 ports, one isolated DIO (8-IN/8-OUT) port, front-facing LED indicators, wide range 12- 48VDC power input with terminal block, and three full-sized Mini cards for 3G/GPRS/Wi-Fi connections. The compact fanless din-rail rugged box PC is designed to operate in a wide temperature ranging from -40°C to +70°C and easy to install and maintain. The smart embedded platform is excellent for space concerned, remote, IoT/M2M, and harsh environments such as power plant, outdoor electricity distribution system, gas station, refinery, mine control room, and any other mission-critical applications.
-
Product
IMPULSE VOLTAGE GENERATOR
-
International Biological Laboratories
The impulse voltage generated in the electric power transmission and distribution system due to lightning or switching phenomena can be simulated by generation of impulse voltage of particular shape in the laboratory.
-
Product
Multi-Wavelength Planar Lightwave Circuit Splitter (PLC Splitter)
PLC-2 × 口口口
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai Planar optical waveguide optical splitter (PLC Splitter) is an integration waveguide optical power distribution device that based on quartz substrate, featured with small size, wide working wavelength range, high reliability and excellent uniformity of optical split, etc. It is especially suitable for connecting local unit with terminal unit in passive optical network (EPON, BPON, GPON, etc.) to achieve optical signal splitting. The main design divide optical signal in optical communication system into multi-way output. The component that we manufactured is with high stability to light source and temperature. And diversified packages can meet customers’ different requirements in application. According to the various requirements, our PLC splitter is with various types: bare fiber type,miniature type, fan-out type,module type, tray type, plug-in type , Blade package type, rack-mounted type, etc.
-
Product
Temperature Chambers For Thermal Tests
-
Before anything reaches out for market distribution, you would need to determine its exact quality and performance to that follows to the point with readings. Thermal and environment testing are some of the most positive aspects to get your materials tested for their underlying performance capacity and reliability in quality.
-
Product
Dynamic Signal Acquisition and Analysis
-
m+p Analyzer systems are available for field and laboratory use from 4 to many hundreds of measurement channels. From gathering simple time history data to narrowband (FFT) spectra, fractional octaves, wavelets, shock response spectra and much more, m+p Analyzer real time analyzers can be used with a wide range of instrumentation hardware including our own m+p VibPilot, m+p VibRunner and m+p VibMobile systems, National Instruments (CompactDAQ USB, PCI, PXI) and VTI Instruments (PCI). Low cost portable instruments to systems for distributed measurements can be configured for maximum flexibility. Measurement data from all sources are stored in a common format so it is easy to compare and handle results from any measurement source.
-
Product
Sinking Particle Size Counter
-
sinking curve acquisition and storage, calculate of particle size, average particle size, surface area, the average error, particle size distribution analysis, calculations, charts and print.
-
Product
Ultra-Ruggedized Data Recorder for Interactive Vehicle Testing
SomatXR CX23-R
-
The ultra-ruggedized SomatXR CX22B-R data recorder is intended for use in harsh environments and reliably stores measured data in applications such as vehicle tests. The recorder records data from other SomatXR modules using an Ethernet connection. At the same time, FireWire allows its use as a gateway for direct data transmission to the PC. Both centralized and distributed measurement systems can thus be implemented.
-
Product
Distribution Amplifiers
-
A complete range of distribution amplifiers are manufactured by Precision Test Systems. A distribution amplifier is used to distribute the output of a frequency reference to many different places. Usually the frequency is 5 or 10 MHz but we manufacture distribution amps from DC to over 2000 MHz. We make some of the industries lowest phase noise products.
-
Product
Transformer/Capacitor Test Sets
-
*Quick and easy check for opens or shorts on transformers or capacitors before energizing*Provides clear indications of open circuits, short connections and confirmation that the test results are OK*Tests overhead, pad-mount and other distribution transformers as well as capacitors and capacitor banks*Tests the primary and secondary sides of de-energized transformers and capacitors without disconnecting*Helps prevent line workers from installing a fuse on a shorted transformer or capacitor*Automatic self-test featureMagnet holds the tester in place while testing
-
Product
4-Channel 200 MHz A/D with 32-Channel DDC, Virtex-6 FPGA - 6U VPX
Model 57662
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 200 MHz 16-bit A/Ds- 32 channels of multiband DDCs (digital downconverters)- Up to 2 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Digital Optical Transport
-
The ATX GigaWave digital optical transport portfolio is designed to fortify cable operators with maximum flexibility and cost efficiencies to support a range of applications and business models. The GigaWave Digital Link Extender (DLX) is optimized to support distributed access architectures (DAA), including Remote PHY (R-PHY) and Remote MACPHY (R-MACPHY), as well as Passive Optical Network (PON), Small Cell/5G and enterprise business services. The GigaWave Digital Link Amplifier-HUB (DLA-HUB) is a field-hardened, gain-flattened EDFA platform that enables the elimination of physical hub sites along long-reach optical routes. The GigaWave digital optical transport portfolio also enables MSOs to leverage the advantages of digital optics over analog, including the capability to transport signals over longer distances and provision additional wavelengths per fiber.
-
Product
Gunshot Detection & Localization System
-
Information System Technologies Inc.
ISTI’s acoustic transient (e.g. gunshot or any other) event detection and localization technologies exploit low-cost distributed sensors with local processing capabilities. Key benefits include: better capture of muzzle blast and ballistic shockwave in urban environments, lower false alarm, real-time response, robustness to loss of sensor nodes, low hardware complexity, flexibility to configure a dynamic local network and ease in deployment. The Graphical User Interface (GUI) allows for control over the sensors and network while providing an overall assessment picture. Unlike existing gunshot detection and gunshot localization systems, the distributed sensing solutions (algorithms and hardware/software) developed by ISTI can support different sensors including acoustic, seismic and IR.
-
Product
32-Ch Isolated Digital Input And 32-Ch Isolated Digital Output EtherCAT Remote I/O Module
AMAX-4856
Isolated Digital I/O Module
Suitable for EtherCAT networks32-ch digital input and 32-ch digital output with 2,500 VDC isolationWide input voltage range (10 ~ 30 VDC)Wide output voltage range (5 ~ 40 VDC) and high output current (350 mA/ch)Quick removable European type connectorLED indicators for I/O statusSupports EtherCAT Distributed Clock (DC) mode and SyncManager modeTwo Rotary switches for up to 256 slave IDs
-
Product
Disciplined OCXOS
-
GPS Disciplined OCXOs (Oven Controlled Crystal Oscillators) are a range of advanced clock modules which provide electrical timing functionality for distributed network systems. These units primarily revolve around the 1PPS (pulse per second) timing synchronisation signal produced by a GPS frequency receiver which is derived from transmitted timing information received from GPS satellite systems.
-
Product
Adaptive Relay, Virtex-6 FPGA - 3U VPX
Model 52624
-
- Modifies 34 IF signals between input and output- Up to 80 MHz IF bandwidth- Two 200 MHz 16-bit A/Ds- Two 800 MHz 16-bit D/As- 34 DDCs and 34 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Dynamic Particle Image Analysis System
iSpect DIA-10
-
Shimadzu's iSpect DIA-10 Dynamic Image Analyzer combines particle size and image analysis technology to offer complete particle characterization. It can perform particle imaging, size analysis, and foreign object detection, and obtain size distributions and number concentration, in as little as two minutes.
-
Product
PLD For Bridging, Infinitely Reconfigurable I/O Expansion.
MachXO
-
*Up to 27.6 Kbits sysMEM™ embedded block RAM and up to 7.7Kbits distributed RAM*SRAM based logic can be reconfigured in milliseconds using JTAG port*IOs support LVCMOS, LVTTL, PCI, LVDS, Bus-LVDS, LVPECL, RSDS*Up to two analog PLLs per device that enable clock multiplication, division, and phase shifting*Available in TQFP, csBGA, caBGA and ftBGA packages
-
Product
8-Channel 200 MHz A/D with DDC, Virtex-7 FPGA - 6U VPX
Model 58761
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four or eight 200 MHz 16-bit A/Ds- Four or eight multiband DDCs- Multiboard programmable beamformer- 4 or 8 GB of DDR3 SDRAM- PCI Express (Gen. 1, 2 & 3) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus formultimodule synchronization- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
AWD Dynamometers
-
Full time AWD vehicles are designed to provide maximum performance regardless of road conditions. In cases where traction is less than ideal, a vehicle may be designed to improve stability and traction at the expense of power. This means adding torque to a spinning wheel or retarding of timing. In order to properly test an AWD vehicle for peak performance, an AWD chassis dynamometer must be able to simulate ideal road-load conditions to the vehicle. This approach allows the vehicle to be evaluated under "optimum" operational conditions; whereby torque is distributed to the vehicle's tires in the same manner that would normally occur when a vehicle has equal traction at all four drive wheels, and is therefore operating at peak efficiency.
-
Product
Metered Power with Audible Alarm (14) 5-15R 1U/0U V/H
EPS-1415-HVA
-
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
Product
Analogue Instruments
-
Devices for installation in control, command and distribution panels. A needle on a gauge allows users to quickly interpret the electrical parameters. Analogue devices provide for fast, visual management, without having to interpret the data in order to determine the status of the installation.
-
Product
High-Resolution Seismic Recording System
DAQlink5
-
DAQlink 5 is the fifth generation of portable seismograph systems. It can be configured as a stand-alone monitoring system, a refraction system, or a distributed seismic reflection system.
