Memory Test Systems
-
product
NFC Conformance Test System
T3111S
The T3111S RIDER NFC Conformance Test System is the Keysight solution for RF Analog and Digital Protocol testing of NFC, EMV and ISO devices. The Test System is based on the Keysight T1141A NFC Test Set and it is complemented by the Keysight's or FIME's robots for accurate and repeatability RF testing. Selected 3rd party positioning robots can also be supported.
-
product
Filter Test System
DU7216/7218
Delta United Instrument Co., Ltd.
Inductance, Q factor, Leakage Inductance, AC Resistance, Capacitance, DC Resistance, Balance,Turn ratio, Open/Short check
-
product
Shaker Systems
C-Series
The MB Dynamics C10E, C40HP, C90HP and C150HP Electrodynamic Shakers comprise current deliverables in a long history of reliable and rugged shakers earning a well-deserved reputation for high performance, longevity, and dependability. They build upon MB’s family of CSeries products (C10, C25, C40, C50, C60, C90, C125, C126, C150, C200, C210, C220) with a heritage spanning 50 years.
-
product
Measurement System
DPS
EYCOM develops and manufactures highly accurate and dependable measurement systems for permittivity, dielectric loss tangent, or permeability by leveraging its accumulated experience and expertise over a long period of time. Capitalizing on such experience and expertise, KEYCOM is committed to developing customized solutions for wide range of specific applications such as flexible circuit board, semiconductor, thin film, millimeter wave and microwave frequency board,
-
product
System Solutions
Diamond offers a range of off-the-shelf and ready-to-build computer and ethernet switch systems that feature great flexibility and expansion capability. Our systems include industrial grade and rugged / Military grade products. Due to the wide range of configuration options, please contact your local Diamond salesperson for specific ordering information and part numbers.
-
product
Measurement System
BLS-I/BCT-400
The BLS-I/BCT-400 measurement systems perform lifetime measurement on monocrystalline or multicrystalline silicon (ingots or bricks) without requiring surface passivation.
-
product
Automatic Transformer Test System
TH2829CX
Changzhou Tonghui Electronic Co., Ltd.
Number of Test PIN: 20 ■ Frequency: 20Hz-1MHz, Resolution: 0.5mHz ■ Signal Level: 5mV-2Vrms(Option:2mV-10Vrms) ■ Test Speed: max. 13ms ■ 7-inch TFT LCD display with a resolution of 800×RGB×480
-
product
Test Automation System for Durability Testing
STARS MATS
STARS MATS is a Mileage Accumulation Test System application available with the STARS Automation platform for chassis dynamometer. The application provides test execution, equipment control, refueling, and vehicle state monitoring to perform long endurance test without the necessity of continuous staff presence. Its flexible design offers a wide range a customization, and it addresses the different testing requirements from manual to fully-automated operation.
-
product
Fully Automated In-line Test System For LED Light Engines
We are pleased to announce that we have received an order for the supply of a fully automated in-line test system for testing LED light engines from ASD Lighting, based in Rotherham. The solution provided, consists of an in-line handler fitted with a vision system. The camera software is capable of learning the position of all LED’s on a new pcb, thereby reducing the time to introduce a new product. In addition to identifying the location of any missing or faulty LED’s the tester measures the colour temperature of every pcb. An image is taken of faulty units with the location of any missing LED’s identified
-
product
Combination Board Functional Test System
QT 4256 ATE
Qmax Test Technologies Pvt. Ltd.
QT 4256 ATE is a combination Board Functional Test System , a main frame Automated Test Equipment (ATE) which can be configured up to maximum of 1280 Bi-directional digital channels ideal for testing circuit card assemblies of high level of complexity and whether it is a legacy or new generation PCB.
-
product
High Voltage, Continuity & Hipot, Cable & Wire Harness Test Systems
CableEye HVX, HVX-21
Fast ● Simple ● Precise
Advanced wiring analyzer scans for continuity (opens, shorts), miswires, resistance, capacitance, components (resistors, diodes, LEDs, capacitors) dielectric breakdown, insulation resistance, intermittent connections
HVX (Item 829) 1500 Vdc, 1000 Vac
HVX-21 (Item 829A) 2100 Vdc, 1200 Vac
For diagnostic and Pass/Fail Testing — Permits expanded testing (compared to models in our low voltage product line) for insulation resistance (IRI) and dielectric breakdown (DWV).
All CableEye testers are suitable for production, fault diagnosis, QC (Quality Control), assembly, and prototyping of standard or custom cables. Each combines test, fault location, design, documentation, labeling, and database storage in one instrument. Tests can be performed on long cables (with or without connectors) or no cables (e.g. connectors, backplanes, PCBs, components).
Standard Features & Benefits:- USB certified, PC-based tester for a versatile, fast, robust system with long life-cycle.
- Multilingual, dynamic, graphic-rich display (netlist & wiring schematic) provides clarity and speeds diagnostics.
- 128 Test Points, expandable to 1024 providing flexibility as your product line changes.
- User-selectable voltage to each connection group in the cable simplifies an otherwise complex process, accelerating testing.
- Programmable Ramp Up, Ramp Down, Dwell Time (same as Test Time), Trip Current, and Trip Delay (same as Soak Time) adds versatility.
- Current leakage detected during HV test phase provides a measure of insulation resistance up to 1 GΩ (HVX) and 5 GΩ (HVX-21) - any leakage current exceeding a preset limit reveals the presence of moisture, flux, or other contamination on exposed contacts.
- Real-time screening for intermittent connections for pinpointing elusive faults and improving quality.
- Automation scripting in a simple, intuitive language allowing non-programmers to reduce operator error by automating repetitive steps.
- Pop-Up Work Instructions. choose the exact amount of detail, imagery, language and automation you need to ensure your work instructions and tests are carried out flawlessly.
- Flexible tolerancing: optionally define as percentages or absolute terms, as well as asymmetrically (e.g. +0%/-10%) for improved yields.
- Barcode-tracking & archival data-logging to achieve error-proof test process and improved traceability & productivity.
- Print PASS/FAIL labels, test reports (with or without color wiring schematics/netlists) and log reports to satisfy ISO9000 reporting requirements.
- Compatible with laptop and touchscreen PCs for fieldwork and rack/off-bench mounting.
Includes:
CB29 board set (Item 759) for bare wire connections; comprehensive PC software with Database of >200 standard cables; 2 yr Product Support Subscription comprising Warranty, free tech support, and free software upgrades.
Select Add-On Options:
Hardware: 128-point Expansion Modules (attach to base); 4-Wire Kelvin Resistance Measurement, 1 mΩ at 1 A; Advanced Measurements; External Measurement Instrument Port (e.g. 10 GΩ Isolation at 100 V); Remote Control Connector for Deadman Switch; Environmental Sensor
Software: PinMap™ fixture editor, Connector Designer™ connector editor, or Autobuild™ guided assembly modules
camiresearch.com |@CAMI_CableEye |+1.978.266.2655 -
product
Dilution-Extractive System
ML675
The Teledyne ML®675 dilution-extractive system can be used in 40CFR75, 40CFR60, 40CFR63, and process control applications. In this system, sample is prepared for analysis by diluting stack gas with clean, dry instrument air at the probe location. Since no moisture is removed with dilution, measurements for SO2, NOx, CO, THC and CO2 are made on a wet basis.
-
product
Mobile Systems
Advanced vehicle-based platforms for real-time detection and identification of CBRN threats in complex and variable urban environments.
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196D
The 16196D surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results – reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement – now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
Fuel Cell Test Systems
For 100Watt DMFC single cell testCompact sizeConsists of electronic load, gas/liquid controller, humidifier and methanol pump etc.
-
product
AVL Battery Test Systems
In modern electrified powertrains (xEVs), huge demands are placed on batteries. These electrochemical energy storage and conversion devices must meet market requirements such as long-lasting high power and energy performance, and dynamic charge and discharge processes.
-
product
AOI & SPI Test Systems
To keep the quality of your production at its best you need a good inspection of your boards. For efficient and detailed in-depth board inspection ensure you have SMT inspection equipment that meets your needs. Our AOI & SPI units will provide the quality you need for reliable inspection of soldering inspection.
-
product
PXIe Isolated Digitizer, 2-channels, 16-bit, 256 V, 32 Msa/Ch memory
M9217A
The M9217A PXIe digitizer is a single slot, 2 isolated input channels, supporting up to 256 V and sampling rate of 20 MSa/s and 16-bit resolution.
-
-
product
HardFiber System
IEC 61850
The HardFiber System is a KEMA tested IEC 61850 Process Bus Solution that allows the mapping of measurements made in the switchyard to protection relays located in the control house using secure communications. The HardFiber System addresses the key technical and logistic challenges affecting the labor required for substation design, construction and maintenance.
-
product
LogiCue Systems
LogiCue 12
LogiCue is a digital cue light system that makes cueing actors and production crew easy and accurate. The LogiCue 12 gives stage managers the ability to control up to 12 different cue lights.
-
product
(100kN) Fatigue Testing Systems
8801
The 8801 servohydraulic testing system meets the challenging demands of a varied range of both dynamic and static testing requirements. The 8801 provides complete testing solutions to satisfy the needs of advanced materials and component testing, and is ideally suited for high- and low-cycle fatigue testing, thermomechanical fatigue testing, and fracture mechanics. The higher capacity of up to 100 kN, a larger working space, a high stiffness, and the precision of alignment all make the 8801 an exceptionally versatile and reliable testing system.
-
product
System Colorimeter
C 3300
System colorimeter for fast measurements on temporal changing light colors with display of the tristimulus values X,Y,Z on three 4¾-digit displays, measurement rates up to 120 readings/s, with system colorimeter head CHS 60, by partial filtering very fine adjusted to the CIE color matching functions.
-
product
Probe Systems
These flexible probe stations are designed for the ever-changing test configurations required in a engineering lab. Combined with durable probes or your own high-speed probes, PacketMicro probe stations are the most cost-effective probing solutions in the industry.
-
product
Video Quality Testing and Monitoring System
Net-Mozaic
The Net-MOZAIC can be used as a stand alone product or an integral part of our Net-xTVMS system. The Net-MOZAIC is normally located at the Head End with access to unencrypted TV channels. Customers define groups of 16 channels at the time. They are then decoded and analyzed for picture quality. Hundreds of channels can be analyzed this way on the round robbin.
-
product
Sensing System
DAS
Our Distributed Acoustic Sensor(DAS) with excellent pattern recognition software can detect and locate the distributed thousanfs of acoustic events. Whenever any vibration or sound around its sensing fiber is detected, our DAS system will process the measured data in real-time and its pattern recognition software will recognize the types of the events, such as digging, pipeline leakage, fence breach, vehicle moving person walking. And, the detected events are reported to the alarm server to help operators take actions to protect theor facilities.
-
product
Ultra-High Performance FLASH and DRAM Memories Test Solution
Magnum V
Teradyne’s Magnum V systems delivers high throughput and high parallel test efficiency for ultra-high performance FLASH and DRAM memories. Magnum V’s largest configuration delivers up to 20,480 digital channels at 1600Mbps per channel.
-
product
Flying Prober Test System
QTOUCH2204C
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built Vision Camera for easy monitoring of probe needle contact.The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision. It also comes with in-built image processing unit with minimum 5 Mega pixel Camera ,tele-centric lens with image processing software, illuminated with LED bar light with controls.
-
product
Brake Test Systems
GIANT Evo
The GIANT Evo is an extension of the well-proven GIANT product portfolio and has been developed to suit the growing demands and needs of the current and future brake markets. Covering the market segments from mini and compact cars to medium sized SUVs as well as large vehicles, this brake testing machine forms the base of HORIBA’s inertia brake dynamometers portfolio. All components are specifically tailored to the needs of the passenger car market segment.
-
product
High Voltage DC Cable Test Systems
We can offer from ±18kVdc to ±30kVdc units which all have automatic earthing for discharging capacitive loads. They are designed to perform tests on installed cables and jointing systems.
