Memory Test Systems
-
Product
Mezzanine System
5047
System
The 5047 provides breakout of all ECM signals for debug, design validation and development. Plated through holes on the PCB allow soldering of probe wires to IO, Data, Power and Serial Identification signals. LEDs indicate presence of 3V, 5V, +12V, -12V and Ground. Elevates the ECM module by 2 mm and saves wear on the ECM carrier board connectors. Since this is a debug too there is no serial identification circuit.
-
Product
Mini LED Backlight Module Automatic Optical Test System
7661-K003
Test System
Chroma 7661-K003 Mini LED Backlight Module Automatic Optical Test System contains a 71803-2 2D color analyzer to measure chromaticity and brightness
-
Product
Digital Test Instruments
Test Instrument
Conduct pattern-based digital tests incorporating the latest parallel, digital, serial, and bus protocols with the PXIe-6943 digital test instrument.
-
Product
NI Vehicle Radar Test System
Test System
VRTS provides automated radar measurement and obstacle simulation capabilities for 76 to 81 GHz automotive radar systems. With VRTS, you can perform precision RF measurements and simulate a wide range of test scenarios for radar hardware and software subsystems, including sensors, advanced driver assistance systems (ADAS), and embedded software. Use VRTS for all phases, from design to manufacturing, of ADAS and radar system test.
-
Product
Isolated Digital I/O 60VDC, 150mA
OTP2 module no.186
Test Platform
The National Instruments PXI-6528, PCI-6528, and PXI-6529 Digital I/O Modules are isolated digital I/O interfaces for PCI and PXI. These modules can use inputs from NI 6528 and PXI 6529 devices to capture the status of sensors, actuators, and logic devices. NI 6528 devices have 24 SSR outputs for switching external devices with input currents up to 150 mA. The NI 6528 and PXI-6529 devices are suitable for a variety of applications, from automotive development and industrial factory automation to aerospace, laboratory research, and biomedical applications due to their high current handling capacity and isolation.
-
Product
Optimize Throughput And Cost For MmWave 5G Device Functional Test
Functional Test
Test engineers always have faced tough new test-coverage challenges. Those introduced by 5G measurements at mmWave are no exception, as they require over-the-air (OTA) radiated test solutions. But never have these pressures seen today’s intense time-to-market, manufacturing volume, and operational expectations! A solution that meets these demands must:
-
Product
Systems Certification
System
Project integration offering a complete turnkey solution including design, engineering, FAA and international regulatory certification services and testing, and installation kit manufacturing.
-
Product
Modular Functional Test Platform
LX-OTP2
Test Platform
The OTP² system platform has recently been available in both the PXI and LXI versions. The OTP2 system platform enables the cost-effective and fast implementation of function test systems based on defined modules and function blocks. Thanks to the open system interfaces, customer-specific adjustments can be made at any time without any problems. When considering options for your next generation functional test system, it is important to assess the entire life cycle of the system and the associated costs and efforts. Use OTP² to accelerate development cycles and reduce the development effort for new functional test systems.
-
Product
Medalist i1000D
U9401B
In-Circuit Test System
The Keysight Medalist i1000D is now even better. Improving from its previous state of an analog-only ICT, the new digital release of the system now features per pin programmable digital cards and a whole new set of intuitive software graphical user interfaces (GUIs) that makes programming and development effortless.
-
Product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
Test Instrument
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
-
Product
VLSI Test System
3380
Test System
The 3380 VSLI test system equipped with a maximum of 1280 I/O channels, 256 VI sources, flexable architecture and comprehensive optional function boards (ADDA/Hi-voltage DPS) can meet the high parallel multi-test tendency.
-
Product
SoC Test Systems
Test System
Specifically designed for high-throughput and high parallel test capabilities to provide the most cost-effective solution for fabless, IDM and testing houses. With the full functions of test capability, high accuracy, powerful software tools and excellent reliability, 3650-EX is ideal for testing consumer devices, high-performance microcontrollers, analog devices and SoC devices.
-
Product
Infotainment Test for Automotive Applications
test
Multimedia operating interfaces are complex control and display devices for functions such as entertainment, telephony, on-board computers and vehicle settings. The functional test of such complex control units and their networking within the vehicle architecture presents a particular challenge in every phase of the product design process.
-
Product
Fixture Self-Test Controller and Calibration Check
AQ818
Test Fixture
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
Product
Battery Management (BMS) Environmental Test System
Test System
The BMS Environmental Test System is a configurable platform simulating the essential signals used by Battery Management Systems (BMS) and cell-monitoring modules with the ability to perform environmental testing on multiple BMS units simultaneously. The system implements single-point value testing to evaluate specific BMS functions such as cell over and under voltage scenarios, cell leakage current, lost communications, or faulty system IO.
-
Product
PCIe 4.0 Test Platform
PXP-400A
Test Platform
The Teledyne LeCroy PXP-400A Test Platform provides a convenient means for testing PCIe 4.0 cards with a self-contained portable and powered passive backplane. The PXP-400A provides power required for both cards under test, and an interposer can be used for connection to a protocol analyzer.
-
Product
2-Module ICT System, I317x Series 6
E9902G
In-Circuit Test System
Keysight's family of i3070 Series 6 In-Circuit Test (ICT) systems are built on a proven technology foundation, and they improve test efficiency with time-tested software, hardware, and programmability. I3070 Series 6 ICT tester supports a wide range of printed circuit board assembly (PCBA) sizes for applications including IoT and 5G, as well as automotive and energy. The i3070 features a unique design that delivers the shortest signal path between measurement circuitry and devices under test to minimize undesired effects from parasitic capacitance, improve immunity to crosstalk, and eliminate stray signal coupling effects, delivering consistent and repeatable measurements. The Series 6 is fully backward compatible with previous systems and makes highly repeatable measurements.
-
Product
Regenerative Battery Pack Test System
17020E
Test System
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
Product
Smart Sensing Systems
System
The Astronics Smart Aircraft System enables the gathering of information through sensor and IoT technology to help airlines gain the valuable insight needed to increase passenger satisfaction, improve operational efficiency, and lower costs.
-
Product
Open Test Platform for High Performance Automotive Applications
TSVP
Test Platform
The R&S®TSVP family of products is an open test platform from Rohde & Schwarz ideal for high performance automated test equipment (ATE) applications. The chassis contains a mechanical frame, digital backplane, analog backplane, mains switching and filtering, power supply and diagnostic extensions. A highlight is the analog bus for routing measurement signals between different slots without additional external wiring.
-
Product
Electronics Functional Test
Functional Test
Functional test for productive manufacturing. Manufacturers of products enabled by electronics must assure proper operation prior to shipment. Bloomy’s line of universal test systems are ideal for functional test of your PCBAs and subassemblies, from the simplest to the most complex. The UTS family of products combines high-performance test instruments, switching, power control and mass-interconnect hardware with our robust UTS software suite into a low-risk, cost-effective and powerful test solution for your device under test (DUT).
-
Product
Ultra-high Performance Solution for Memory Device Test
Magnum EPIC
-
Teradyne’s Magnum EPIC is a high-performance test solution for latest generation DRAM devices. These devices are key enablers for technologies like 5G, AI, cloud computing, autonomous vehicles, AR/VR and applications with high definition graphics.
-
Product
Volatile Memory
-
CAES offers an extensive volatile memory portfolio developed to handle the demands of harsh space and terrestrial environments.
-
Product
6TL23 Off-Line Seat Operation Base Test Platform
H71002300
Test Platform
The 6TL23 is a bare rack for creating Off-Line, modular, flexible and reliable Base test platforms. The overall rack capacity is 18U (580mm depth). The rack is ideal for sit-down operation, since there’s space for the operator’s legs under the fixture receiver.
-
Product
Headlamp Test Platform
Test Platform
Leverage 25+ years of automotive test experience, with the specialized design and manufacturing of automotive lighting testers. Using specialized know-how in this field, including photometric, electro-mechanical equipment and software solutions, accelerate your time to market with a higher quality product.
-
Product
Wireless Device Functional Test Reference Solution
Functional Test
The Keysight S8890A Wireless Device Functional Test Reference Solution provides an automation environment which is both simple to use, yet comprehensive and powerful. Based on the Test Automation Platform www.keysight.com/find/TAP, S8890A provides optional instrument driver/plug-ins offering simplified logically grouped control steps. These steps can be sequenced, looped and swept to provide powerful individual test cases or comprehensive sequences. Each driver/plug-in is provided with extensive starter sample test cases which can be modified by Keysight or the end user the UE to be tested. Plug-in options:
-
Product
In-Line 2-Module In-Circuit Test System; i337x, Series 5i
E9988E
In-Circuit Test System
Short wire fixturing eliminates problems commonly found with long wire fixturing, such as noise and deterioration of test stability. This translates into transportable, repeatable and stable tests on your i3070 Series 5i, even if you need to deploy tests halfway across the globe, or on different manufacturing sites.
-
Product
PXI Test System Dev, Debug & Monitor Software
InstrumentStudio
Test System
InstrumentStudio is free application software that provides an integrated approach to interactive PXI measurements. InstrumentStudio helps you to unify your display, export instrument configurations to code, and monitor and debug your automated test system. You can view data on unified displays with large, high-resolution monitors, and then capture multi-instrument screenshots and measurement results.
-
Product
Test System
MFTS500
-
Computer Gesteuerte Systeme GmbH
The MFTS500-System is specially designed for the testing of electronic control units (ECUs). It can be configured to be used as a development or as a production tester. Every effort has been made during development and design to ensure that the system is flexible and cost effective.
